Application Notes |

STM32F10xxx TIM application examples

Application Note

Format: (269 kb)

Last Updated: 27/06/2007

Pages: 24

Related Datasheets

Medium-density access line, ARM-based 32-bit MCU with 32 to 128 KB Flash, six timers, ADC and 7 communication interfaces

Medium-density performance line ARM-based 32-bit MCU with 32 to 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces

Raw Ascii Text- ( Hide )
(Unformatted textual content of the document used by search engines)

AN2581 Application note
STM32F10xxx TIM application examples
Introduction
This application note is intended to provide practical application examples of the STM32F10xxx TIMx peripheral use. This document, its associated firmware, and other such application notes are written to accompany the STM32F10xxx firmware library. These are available for download from the STMicroelectronics website: www.st.com.

June 2007

Rev 1

1/24
www.st.com

Contents

AN2581 - Application note

Contents
1 STM32F10xxx TIMx output compare mode . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 1.2 1.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2

Delay generation in TIMx output compare active mode . . . . . . . . . . . . 6
2.1 2.2 2.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3

STM32F10xxx TIMx output compare inactive mode . . . . . . . . . . . . . . . 8
3.1 3.2 3.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4

STM32F10xxx TIMx pulse width modulation mode . . . . . . . . . . . . . . . 10
4.1 4.2 4.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5

TIMx output compare timing mode: time-base generation . . . . . . . . . 12
5.1 5.2 5.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6

STM32F10xxx TIMx PWM input mode . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.1 6.2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

7

Generating an OPM waveform after an edge on TIMx TIx input . . . . . 15
7.1 7.2 7.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2/24

AN2581 - Application note

Contents

8

Synchronizing TIMx peripherals in parallel mode . . . . . . . . . . . . . . . . 17
8.1 8.2 8.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

9

Synchronizing TIMx peripherals in cascade mode . . . . . . . . . . . . . . . 19
9.1 9.2 9.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

10

Synchronizing several timers TIMx to an external trigger . . . . . . . . . . 21
10.1 10.2 10.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Firmware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 TIMx output signal behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

11

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3/24

STM32F10xxx TIMx output compare mode

AN2581 - Application note

1
1.1

STM32F10xxx TIMx output compare mode
Overview
This section provides a description of how to configure the TIM peripheral in output compare mode to generate four different signals with four different frequencies.

1.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. The TIMxCLK frequency is set to 36 MHz, the prescaler is set to 0x2 and used in the output compare toggle mode. TIM2 counter clock = TIMxCLK / (Prescaler +1) = 12 MHz The TIM2_CCR1 register value is equal to 0x8000: CC1 update rate = TIM2 counter clock / CCR1_Val = 366.2 Hz, so TIM2_CH1 generates a periodic signal with a frequency equal to 183.1 Hz. The TIM2_CCR2 register is equal to 0x4000: CC2 update rate = TIM2 counter clock / CCR2_Val = 732.4 Hz so TIM2_CH2 generates a periodic signal with a frequency equal to 366.3 Hz. The TIM2_CCR3 register is equal to 0x2000: CC3 update rate = TIM2 counter clock / CCR3_Val = 1464.8 Hz so the TIM2_CH3 generates a periodic signal with a frequency equal to 732.4 Hz. The TIM2_CCR4 register is equal to 0x1000: CC4 update rate = TIM2 counter clock / CCR4_Val = 2929.6 Hz so the TIM2_CH4 generates a periodic signal with a frequency equal to 1464.8 Hz. This firmware is provided as TIM example 1 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

4/24

AN2581 - Application note

STM32F10xxx TIMx output compare mode

1.3

TIMx output signal behavior
To display the four signals (see Figure 1), connect an oscilloscope to the following pins:

PA0 (TIM2_CH1) PA1 (TIM2_CH2) PA2 (TIM2_CH3) PA3 (TIM2_CH4) TIM2 output signals

Figure 1.

5/24

Delay generation in TIMx output compare active mode

AN2581 - Application note

2

Delay generation in TIMx output compare active mode
Overview
This section provides a description of how to configure the TIM peripheral to generate four different signals with four different delays.

2.1

2.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. The TIMxCLK frequency is set to 36 MHz, the prescaler is set to 35999 and used in the output compare active mode. TIM2 counter clock = TIMxCLK / (Prescaler +1) = 1 kHz The TIM2_CCR1 register value is equal to 1000: TIM2_CH1 delay = CCR1_Val/TIM2 counter clock = 1000 ms so the TIM2_CH1 generates a signal with a delay equal to 1000 ms. The TIM2_CCR2 register value is equal to 500: TIM2_CH2 delay = CCR2_Val/TIM2 counter clock = 500 ms so the TIM2_CH2 generates a signal with a delay equal to 500 ms. The TIM2_CCR3 register value is equal to 250: TIM2_CH3 delay = CCR3_Val/TIM2 counter clock = 250 ms so the TIM2_CH3 generates a signal with a delay equal to 250 ms. The TIM2_CCR4 register value is equal to 125: TIM2_CH4 delay = CCR4_Val/TIM2 counter clock = 125 ms so the TIM2_CH4 generates a signal with a delay equal to 125 ms. The delay corresponds to the time difference between the rising edge of the PC6 signal and the rising edge of the TIM2_CHx signal. This firmware is provided as TIM example 2 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

6/24

AN2581 - Application note

Delay generation in TIMx output compare active mode

2.3

TIMx output signal behavior
To display the four different signals (see Figure 2), connect an oscilloscope to:

PC6 PA0 (TIM2_CH1) PA1 (TIM2_CH2) PA2 (TIM2_CH3) PA3 (TIM2_CH4) TIM2 output signals

Figure 2.

7/24

STM32F10xxx TIMx output compare inactive mode

AN2581 - Application note

3
3.1

STM32F10xxx TIMx output compare inactive mode
Overview
This section provides a description of how to configure the TIM peripheral in the output compare inactive mode with the corresponding Interrupt requests for each channel.

3.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. The TIMxCLK frequency is set to 36 MHz, the prescaler is set to 35999 and used in output compare inactive mode. TIM2 counter clock = TIMxCLK / (Prescaler +1) = 1 kHz The TIM2_CCR1 register value is equal to 1000: TIM2_CC1 delay = CCR1_Val/TIM2 counter clock = 1000 ms so PC6 is reset after a delay equal to 1000 ms. The TIM2_CCR2 register value is equal to 500: TIM2_CC2 delay = CCR2_Val/TIM2 counter clock = 500 ms so PC7 is reset after a delay equal to 500 ms. The TIM2_CCR3 register value is equal to 250: TIM2_CC3 delay = CCR3_Val/TIM2 counter clock = 250 ms so PC8 is reset after a delay equal to 250 ms. The TIM2_CCR4 register value is equal to 125: TIM2_CC4 delay = CCR4_Val/TIM2 counter clock = 125 ms so PC9 is reset after a delay equal to 125 ms. While the counter is lower than the Output compare register values that determine the output delay, the PC6, PC7, PC8 and PC9 pins are driven High. When the counter value reaches the Output compare register values, the Output Compare interrupts are generated and, in the handler routine, these pins are driven Low. This firmware is provided as TIM example 3 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

8/24

AN2581 - Application note

STM32F10xxx TIMx output compare inactive mode

3.3

TIMx output signal behavior
To display the different signals (see Figure 3), connect an oscilloscope to:

PC6 (CH1) PC7 (CH2) PC8 (CH3) PC9 (CH4) GPIOC: PC6, PC7, PC7 and PC9 signals

Figure 3.

9/24

STM32F10xxx TIMx pulse width modulation mode

AN2581 - Application note

4
4.1

STM32F10xxx TIMx pulse width modulation mode
Overview
This section provides a description of how to configure the TIM peripheral in PWM (pulse width modulation) mode.

4.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. The TIMxCLK frequency is set to 36 MHz, the prescaler is 0 so the TIM3 counter clock frequency is 36 MHz. TIM3 is running at 36 kHz: TIM3 frequency = TIM3 counter clock/(TIM3_ARR + 1) The TIM3_CCR1 register value is equal to 0x1F4, so TIM3_CH1 generates a PWM signal with a frequency equal to 36 kHz and a duty cycle equal to 50%: TIM3_CH1 duty cycle = TIM3_CCR1/ (TIM3_ARR + 1) × 100 = 50% The TIM3_CCR2 register value is equal to 0x177, so the TIM3_CH2 generates a PWM signal with a frequency equal to 36 kHz and a duty cycle equal to 37.5%: TIM3_CH2 duty cycle = TIM3_CCR2/ (TIM3_ARR + 1) × 100 = 37.5% The TIM3_CCR3 register value is equal to 0xFA, so the TIM3_CH3 generates a PWM signal with a frequency equal to 36 kHz and a duty cycle equal to 25%: TIM3_CH3 duty cycle = TIM3_CCR3/ (TIM3_ARR + 1) × 100 = 25% The TIM3_CCR4 register value is equal to 0x7D, so the TIM3_CH4 generates a PWM signal with a frequency equal to 36 kHz and a duty cycle equal to 12.5%: TIM3_CH4 duty cycle = TIM3_CCR4/ (TIM3_ARR + 1) × 100 = 12.5% The PWM waveform can be displayed using an oscilloscope. This firmware is provided as TIM example 4 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

10/24

AN2581 - Application note

STM32F10xxx TIMx pulse width modulation mode

4.3

TIMx output signal behavior
To display the four different signals (see Figure 4), connect an oscilloscope to:

PA6: (TIM3_CH1) PA7: (TIM3_CH2) PB0: (TIM3_CH3) PB1: (TIM3_CH4) TIM3 output signals

Figure 4.

11/24

TIMx output compare timing mode: time-base generation

AN2581 - Application note

5

TIMx output g en e r a t i o n
Overview

compare

timing

mode:

time-base

5.1

This section provides a description of how to configure the TIM peripheral in output compare timing mode with the corresponding interrupt requests for each channel in order to generate four different time bases.

5.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. The TIMxCLK frequency is set to 36 MHz, the prescaler is 0x4 so the TIM2 counter clock frequency is 7.2 MHz. The TIM2_CCR1 register value is equal to 0xC000 CC1 update rate = TIM2 counter clock / CCR1_Val = 146.48 Hz, so TIM2_CH1 generates an interrupt every 6.8 ms The TIM2_CCR2 register is equal to 0x8000, CC2 update rate = TIM2 counter clock / CCR2_Val = 219.7 Hz, so TIM2_CH2 generates an interrupt every 4.55 ms The TIM2_CCR3 register is equal to 0x4000, CC3 update rate = TIM2 counter clock / CCR3_Val = 439.4Hz, so TIM2_CH3 generates an interrupt every 2.27 ms The TIM2_CCR4 register is equal to 0x2000, CC4 update rate = TIM2 counter clock / CCR4_Val = 878.9 Hz, so TIM2_CH4 generates an interrupt every 1.13 ms. When the counter value reaches the Output compare register values, the Output Compare interrupts are generated and, in the handler routine, 4 pins (PC6, PC7, PC8 and PC9) are toggled at the following frequencies:

PC6: 73.24 Hz (CC1) PC7: 109.8 Hz (CC2) PC8: 219.7 Hz (CC3) PC9: 439.4 Hz (CC4)

This firmware is provided as TIM example 5 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

12/24

AN2581 - Application note

TIMx output compare timing mode: time-base generation

5.3

TIMx output signal behavior
Connect an oscilloscope to PC6, PC7, PC8 and PC9 to display the different time-base signals as shown in Figure 5. Figure 5. GPIOD signals: PC6, PC7, PC8 and PC9

13/24

STM32F10xxx TIMx PWM input mode

AN2581 - Application note

6
6.1

STM32F10xxx TIMx PWM input mode
Overview
This section provides a description of how to use the TIM peripheral to measure the frequency and duty cycle of an external signal.

6.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. The TIMxCLK frequency is set to 72 MHz, the prescaler is 0x0 so the TIM2 counter clock frequency is 72 MHz. So the minimum frequency value to measure is 1100 Hz. TIM2 is configured in PWM input mode: the external signal is connected to TIM2_CH2 (PA1) used as the input pin. To measure the frequency and duty cycle, the TIM2 CC2 interrupt request is used, so in the TIM2_IRQ handler routine, the frequency and duty cycle of the external signal are computed. The "Frequency" variable contains the external signal frequency: Frequency = TIM2 counter clock / TIM2_CCR2 in Hz, The "Duty_Cycle" variable contains the external signal duty cycle: Duty_Cycle = (TIM2_CCR1*100)/(TIM2_CCR2) in %. This firmware is provided as TIM example 6 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

14/24

AN2581 - Application note

Generating an OPM waveform after an edge on TIMx TIx input

7

Generating an OPM waveform after an edge on TIMx TIx input
Overview
This section provides a description of how to use the TIM peripheral to generate an OPM (one pulse mode) waveform after the rising edge of an external signal is received on the timer input pin (TI).

7.1

7.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. The TIMxCLK frequency is set to 72 MHz, the prescaler is 0x1 so the TIM2 counter clock frequency is 36 MHz. The autoreload value is 0xFFFF (TIM2_ARR), so the maximum frequency value to trigger the TIM2 input is 500 Hz. TIM2 is configured as follows: the one pulse mode is used, the external signal is connected to the TIM2_CH2 pin (PA1), the rising edge is used as the active edge, the one-pulse signal is output on TIM2_CH1 (PA0). TIM_Pulse defines the delay value that is fixed to 455.08 s: delay = CCR1/TIM2 counter clock = 455.08 s (TIM_Period - TIM_Pulse) defines the one-pulse value, the pulse value is fixed to 1.365 ms: One-pulse value = (TIM_Period - TIM_Pulse)/TIM2 counter clock = 1.365 ms This firmware is provided as TIM example 7 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

15/24

Generating an OPM waveform after an edge on TIMx TIx input

AN2581 - Application note

7.3

TIMx output signal behavior
Connect the external signal to measure to the TIM2 CH2 pin (PA1). Connect the TIM2_CH1 (PA0) pin to an oscilloscope to show the waveform. In Figure 6, the Ch1 presents the input signal triggering TIM2 and Ch2 is connected to TIM2_CH2 and presents the TIM2 one-pulse signal. Figure 6. TIM2 output signal

16/24

AN2581 - Application note

Synchronizing TIMx peripherals in parallel mode

8
8.1

Synchronizing TIMx peripherals in parallel mode
Overview
This section provides a description of how to synchronize TIMx peripherals in parallel mode.

8.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. Timer synchronization in parallel mode: 1. TIM2 is configured as the master timer: 2. PWM mode is used The TIM2 update event is used as the trigger output PWM mode is used ITR1 (TIM2) is used as the input trigger for both slaves Gated mode is used, so starts and stops of slave counters are controlled by the master trigger output signal (update event)

TIM3 and TIM4 are slaves for TIM2

The master timer, TIM2, is running at 281.250 kHz and the duty cycle is equal to 25%. The TIM3 is running at: (TIM2 frequency) / (TIM3 Period + 1) = 28.1250 kHz and its duty cycle is equal to: TIM3_CCR1/(TIM3_ARR + 1) = 30% The TIM4 is running at: at (TIM2 frequency) / (TIM4 Period + 1) = 56.250 kHz and its duty cycle is equal to: TIM4_CCR1/(TIM4_ARR + 1) = 60% This firmware is provided as TIM example 8 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

17/24

Synchronizing TIMx peripherals in parallel mode

AN2581 - Application note

8.3

TIMx output signal behavior
Connect the TIM2_CH1 (PA0), TIM3_CH1 (PA6) and TIM4_CH1 (PB6) pins to an oscilloscope to display the waveforms (see Figure 7). Figure 7. TIM2_CH1 (PA0), TIM3_CH1 (PA6) and TIM4_CH1 (PB6) output signals

18/24

AN2581 - Application note

Synchronizing TIMx peripherals in cascade mode

9
9.1

Synchronizing TIMx peripherals in cascade mode
Overview
This section provides a description of how to synchronize TIM peripherals in cascade mode.

9.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. Timer synchronization in cascade mode: 1. TIM2 is configured as the master timer: 2. 3. PWM mode is used the TIM2 update event is used as the trigger output PWM mode is used ITR1 (TIM2) is used as the input trigger Gated mode is used, so starts and stops of the slave counter are controlled by the master trigger output signal (TIM2 update event) The TIM3 update event is used as the trigger output. PWM mode is used ITR2 (TIM3) is used as the input trigger Gated mode is used, so starts and stops of the slave counter are controlled by the master trigger output signal (TIM3 update event)

TIM3 is a slave for TIM2 and the master for TIM4:

TIM4 is a slave for TIM3:

The TIMxCLK is fixed to 72 MHz, the TIM2 counter clock frequency is 72 MHz. The master timer, TIM2, is running at the TIM2 frequency: TIM2 frequency = (TIM2 counter clock)/ (TIM2 Period + 1) = 281.250 kHz and duty cycle = TIM2_CCR1/(TIM2_ARR + 1) = 25%. The TIM3 is running at: (TIM2 frequency)/ (TIM3 Period + 1) = 70.312 kHz and duty cycle = TIM3_CCR1/(TIM3_ARR + 1) = 25% The TIM4 is running at: (TIM3 frequency)/ (TIM4 Period + 1) = 17.578 Hz and duty cycle = TIM4_CCR1/(TIM4_ARR + 1) = 25% This firmware is provided as TIM example 9 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

19/24

Synchronizing TIMx peripherals in cascade mode

AN2581 - Application note

9.3

TIMx output signal behavior
Connect the TIM2_CH1 (PA0), TIM3_CH1 (PA6) and TIM4_CH1 (PB6) pins to an oscilloscope to display the waveforms (see Figure 8). Figure 8. TIM2_CH1 (PA0), TIM3_CH1 (PA6) and TIM4_CH1 (PB6) signals

20/24

AN2581 - Application note

Synchronizing several timers TIMx to an external trigger

10

Synchronizing several timers TIMx to an external trigger
Overview
This section provides a description of how to synchronize TIMx peripherals in cascade mode to an external trigger.

10.1

10.2

Firmware description
The provided firmware includes the TIMx driver that supports all TIMx functionalities through a set of functions. An example of use for most of these functions is provided. Timer synchronization in cascade mode with an external trigger: 1. TIM2 is configured as the master timer: 2. Toggle mode is used the TIM2 enable event is used as the trigger output

TIM2 is configured as a slave timer for an external trigger connected to the TIM2 TI2 pin (TIM2_CH2 configured as an input pin): TIM2 TI2FP2 is used as the trigger input rising edge is used to enable and stop TIM2: gated mode Toggle mode is used ITR1 (TIM2) is used as the input trigger Gated mode is used, so starts and stops of the slave counter are controlled by the master trigger output signal (TIM2 enable event) the TIM3 enable event is used as the trigger output Toggle mode is used ITR2 (TIM3) is used as the input trigger Gated mode is used, so starts and stops of the slave counter are controlled by the master trigger output signal (TIM3 enable event)

3.

TIM3 is a slave for TIM2 and the master for TIM4,

4.

TIM4 is a slave for TIM3

TIMxCLK is fixed to 72 MHZ, the prescaler is equal to 0x2 so the TIMx clock counter frequency is 24 MHz. The three timers are running at: TIMx frequency = TIMx clock counter/ 2 × (TIMx_Period + 1) = 162.1 kHz The starts and stops of the TIM2 counter are controlled by the external trigger. TIM3 starts and stops are controlled by TIM2, and TIM4 starts and stops are controlled by TIM3. This firmware is provided as TIM example 10 in the STM32F10xxx firmware library, available from the STMicroelectronics microcontrollers website.

21/24

Synchronizing several timers TIMx to an external trigger

AN2581 - Application note

10.3

TIMx output signal behavior
Connect an external trigger with a frequency lower than or equal to 40 kHz, to the TIM2_CH2 pin. In this example the frequency is equal to 5 kHz. Connect the TIM2_CH1 (PA0), TIM3_CH1 (PA6) and TIM4_CH1 (PB6) pins to an oscilloscope to display the waveforms (see Figure 9). Figure 9. TIM2_CH1 (PA0), TIM3_CH1 (PA6) and TIM4_CH1 (PB6) signals

22/24

AN2581 - Application note

Revision history

11

Revision history
Table 1.
Date 26-Jun-2007

Document revision history
Revision 1 Initial release. Changes

23/24

AN2581 - Application note

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com

24/24

Document Number: 13658



All rights reserved © 2008 STMicroelectronics :: Terms Of Use :: Privacy Policy