ST72325xx
8-bit MCU with 16 to 60K Flash/ROM, ADC, CSS, 5 timers, SPI, SCI, I2C interface
Features
Memories 16K to 60K dual voltage High Density Flash (HDFlash) or up to 32K ROM with read-out protection capability. In-Application Programming and In-Circuit Programming for HDFlash devices 512 to 2048 bytes RAM HDFlash endurance: 100 cycles, data retention: 40 years at 85C Clock, reset and supply management Enhanced low voltage supervisor (LVD) for main supply and auxiliary voltage detector (AVD) with interrupt capability Clock sources: crystal/ceramic resonator oscillators, internal RC oscillator and bypass for external clock PLL for 2x frequency multiplication Four Power Saving Modes: Halt, Active-Halt, Wait and Slow Clock Security System Interrupt management Nested interrupt controller 14 interrupt vectors plus TRAP and RESET Top Level Interrupt (TLI) pin on 64-pin devices 9/6 external interrupt lines (on 4 vectors) Up to 48 I/O ports 48/36/32/24 multifunctional bidirectional I/O lines 34/26/22/17 alternate function lines 16/13/12/10 high sink outputs 5 timers Main Clock Controller with: Real time base, Beep and Clock-out capabilities
LQFP64 10 x 10
LQFP44 10 x 10
LQ FP48 7x7
LQ FP32 7x7
LQFP64 14 x 14
SDIP42 600 mil
SDIP32 400 mil
Configurable watchdog timer Two 16-bit timers with: 2 input captures, 2 output compares, external clock input on one timer, PWM and pulse generator modes 8-bit PWM Auto-reload timer with: 2 input captures, 4 PWM outputs, output compare and time base interrupt, external clock with event detector 3 Communication interfaces SPI synchronous serial interface SCI asynchronous serial interface I2C multimaster interface 1 Analog peripheral (low current coupling) 10-bit ADC with up to 16 robust input ports Instruction set 8-bit Data Manipulation 63 Basic Instructions 17 main Addressing Modes 8 x 8 Unsigned Multiply Instruction Development tools Full hardware/software development package DM (Debug module)
ST72325R9 / ST72325AR9 / ST72325C9 /ST72325J9
Flash 60K 2048(256)
Table 1. Device summary
Features
Program memory - bytes RAM (stack) - bytes Operating Voltage Temp. Range Package
ST72325S4 / ST72325J4 / ST72325K4
Flash/ROM 16K 512 (256)
ST72325S 6 / ST72325J6 / ST72325K6
Flash/ROM 32K 1024(256) 3.8V to 5.5V up to -40C to +125C
ST72325J7
Flash 48K 1536 (256)
LQFP48(S), LQFP44/SDIP42 (J), LQFP48(S) , LQFP44/ SDIP42 (J), LQFP44 (J) LQFP32/DIP32 (K) LQFP32/DIP32 (K)
LQFP64 14x14(R), LQFP64 10x10(AR), LQFP48(C), LQFP44 (J)
October 2008
Rev 4
1/197
1
Table of Contents
1 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 PIN DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 REGISTER & MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4 FLASH PROGRAM MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.3 STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.3.1 Read-out Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.4 ICC INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.5 ICP (IN-CIRCUIT PROGRAMMING) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.6 IAP (IN-APPLICATION PROGRAMMING) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.7 RELATED DOCUMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.7.1 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5 CENTRAL PROCESSING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.3 CPU REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 6 SUPPLY, RESET AND CLOCK MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.1 PHASE LOCKED LOOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.2 MULTI-OSCILLATOR (MO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6.3 RESET SEQUENCE MANAGER (RSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 6.3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3.2 Asynchronous External RESET pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3.3 External Power-On RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3.4 Internal Low Voltage Detector (LVD) RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3.5 Internal Watchdog RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 SYSTEM INTEGRITY MANAGEMENT (SI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4.1 Low Voltage Detector (LVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4.2 Auxiliary Voltage Detector (AVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4.3 Clock Security System (CSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4.4 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4.5 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 29 30 30 30 31 31 32 34 34 35 36 36
7.2 MASKING AND PROCESSING FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7.3 INTERRUPTS AND LOW POWER MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 7.4 CONCURRENT & NESTED MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 7.5 INTERRUPT REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 7.6 EXTERNAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 7.6.1 I/O Port Interrupt Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 7.7 EXTERNAL INTERRUPT CONTROL REGISTER (EICR) . . . . . . . . . . . . . . . . . . . . . . . . . 43 8 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 197 8.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 8.2 SLOW MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2/197
1
Table of Contents
8.3 WAIT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 8.4 ACTIVE-HALT AND HALT MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 8.4.1 ACTIVE-HALT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.2 HALT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2.1 Input Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2.2 Output Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2.3 Alternate Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 I/O PORT IMPLEMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 48 50 50 50 50 50 53
9.2 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.4 LOW POWER MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 9.5 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 9.5.1 I/O Port Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 10 ON-CHIP PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 10.1 WATCHDOG TIMER (WDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 10.1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.4 How to Program the Watchdog Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.5 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.6 Hardware Watchdog Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.7 Using Halt Mode with the WDG (WDGHALT option) . . . . . . . . . . . . . . . . . . . . . . . 10.1.8 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.9 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 MAIN CLOCK CONTROLLER WITH REAL TIME CLOCK AND BEEPER (MCC/RTC) . . 10.2.1 Programmable CPU Clock Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2.2 Clock-out Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2.3 Real Time Clock Timer (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2.4 Beeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2.5 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2.7 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3 PWM AUTO-RELOAD TIMER (ART) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3.2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3.3 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4 16-BIT TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.4 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.5 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.6 Summary of Timer Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.7 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.5 SERIAL PERIPHERAL INTERFACE (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 56 56 57 59 59 59 59 59 61 61 61 61 61 62 62 62 64 64 65 69 73 73 73 73 85 85 85 86 92
3/197
1
Table of Contents
10.5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 10.5.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 10.5.3 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 10.5.4 Clock Phase and Clock Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 10.5.5 Error Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 10.5.6 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 10.5.7 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 10.5.8 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 10.6 SERIAL COMMUNICATIONS INTERFACE (SCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 10.6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6.3 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6.5 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6.7 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7 I2C BUS INTERFACE (I2C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7.3 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7.5 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7.7 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8 10-BIT A/D CONVERTER (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8.2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8.4 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8.5 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8.6 Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 CPU ADDRESSING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1.1 Inherent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1.2 Immediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1.3 Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1.4 Indexed (No Offset, Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1.5 Indirect (Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1.6 Indirect Indexed (Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1.7 Relative mode (Direct, Indirect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 INSTRUCTION GROUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 103 103 105 112 112 113 119 119 119 119 121 125 125 126 132 132 132 133 133 133 134 136 136 137 137 137 137 137 138 138 139
12 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 12.1 PARAMETER CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 12.1.1 12.1.2 12.1.3 12.1.4 12.1.5 Minimum and Maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 142 ... Loading capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
4/197
Table of Contents
12.2 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.2.1 Voltage Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.2 Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.3 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3 OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3.1 General Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3.2 Operating Conditions with Low Voltage Detector (LVD) . . . . . . . . . . . . . . . . . . . 12.3.3 Auxiliary Voltage Detector (AVD) Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3.4 External Voltage Detector (EVD) Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.4 SUPPLY CURRENT CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.4.1 CURRENT CONSUMPTION . . .. . .. . .. . .. . .. . .. . ... 12.4.2 Supply and Clock Managers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.4.3 On-Chip Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5 CLOCK AND TIMING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.1 General Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.2 External Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.3 Crystal and Ceramic Resonator Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.4 RC Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.5 Clock Security System (CSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.6 PLL Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 MEMORY CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 143 144 144 144 145 145 145 146 146 147 148 149 149 149 150 153 154 154 155
12.6.1 RAM and Hardware Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 12.6.2 FLASH Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 12.7 EMC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 12.7.1 Functional EMS (Electro Magnetic Susceptibility) . . . . . . . . . . . . . . . . . . . . . . . . 12.7.2 Electro Magnetic Interference (EMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.7.3 Absolute Maximum Ratings (Electrical Sensitivity) . . . . . . . . . . . . . . . . . . . . . . . 12.8 I/O PORT PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 157 158 159
12.8.1 General Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 12.8.2 Output Driving Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 12.9 CONTROL PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 12.9.1 Asynchronous RESET Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 12.9.2 ICCSEL/VPP Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 12.10TIMER PERIPHERAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 12.10.1 8-Bit PWM-ART Auto-Reload Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 12.10.2 16-Bit Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 12.11COMMUNICATION INTERFACE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . 166 12.11.1 SPI - Serial Peripheral Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 12.11.2 I2C - Inter IC Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 12.1210-BIT ADC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 12.12.1 Analog Power Supply and Reference Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.12.2 General PCB Design Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.12.3 ADC Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 PACKAGE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1 PACKAGE MECHANICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 172 173 174 174
13.2 THERMAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
5/197
Table of Contents
13.3 SOLDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 14 ST72325 DEVICE CONFIGURATION AND ORDERING INFORMATION . . . . . . . . . . . . . . . 181 14.1 FLASH OPTION BYTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 14.2 DEVICE ORDERING INFORMATION AND TRANSFER OF CUSTOMER CODE . . . . . 183 14.3 DEVELOPMENT TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 14.3.1 Starter kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2 Development and debugging tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.3 Programming tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.4 Socket and Emulator Adapter Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4 ST7 APPLICATION NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 187 187 188 189
15 KNOWN LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 15.1 ALL DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 15.1.1 Unexpected Reset Fetch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.2 External interrupt missed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.3 Clearing active interrupts outside interrupt routine . . . . . . . . . . . . . . . . . . . . . . . 15.1.4 SCI Wrong Break duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.5 16-bit Timer PWM Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.6 TIMD set simultaneously with OC interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.7 I2C Multimaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.8 Pull-up always active on PE2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.9 ADC accuracy 16/32K Flash devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 REVISION HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 192 193 194 194 194 194 195 195 196
197
6/197
ST72325xx
1 DESCRIPTION
The ST72F325 Flash and ST72325 ROM devices are members of the ST7 microcontroller family designed for mid-range applications. They are derivatives of the ST72321 and ST72324 devices, with enhanced characteristics and robust Clock Security System. All devices are based on a common industrystandard 8-bit core, featuring an enhanced instruction set and are available with Flash or ROM program memory. The ST7 family architecture offers both power and flexibility to software developers, enabling the design of highly efficient and compact application code. The on-chip peripherals include an A/D converter, a PWM Autoreload timer, 2 general purpose timers, I2C bus, SPI interface and an SCI interface. For power economy, microcontroller can switch dynamically into WAIT, SLOW, ACTIVE-HALT or Figure 1. Device Block Diagram
8-BIT CORE ALU RESET VPP TLI VSS VDD EVD OSC1 OSC2 CONTROL
HALT mode when the application is in idle or stand-by state. Typical applications are consumer, home, office and industrial products. The devices feature an on-chip Debug Module (DM) to support in-circuit debugging (ICD). For a description of the DM registers, refer to the ST7 ICC Protocol Reference Manual. Main Differences with ST72321: LQFP48 and LQFP32 packages Clock Security System Internal RC, Readout protection, LVD and PLL without limitations Negative current injection not allowed on I/O port PB0 (instead of PC6). External interrupts have Exit from Active Halt mode capability.
PROGRAM MEMORY (16K - 60K Bytes1)) RAM (512 - 2048 Bytes1))
LVD AVD OSC ADDRESS AND DATA BUS MCC/RTC/BEEP WATCHDOG DEBUG MODULE I2C PORT A PA7:0 (8 bits on AR devices) (5 bits on C/J devices) (4 bits on K devices)
PORT F PF7:0 (8 bits on AR devices) (6 bits on C/J devices) (5 bits on K devices) TIMER A BEEP PORT E PE7:0 (8 bits on AR devices) (2 bits on C/J/K devices)
PORT B PWM ART PB7:0 (8 bits on AR devices) (5 bits on C/J devices) (3 bits on K devices)
PORT C SCI TIMER B PORT D PC7:0 (8 bits)
PD7:0 (8 bits on AR devices) (6 bits on C/J devices) (2 bits on K devices) VAREF VSSA
1)
SPI 10-BIT ADC
ROM devices have up to 32 Kbytes of program memory and up to 1 Kbyte of RAM.
7/197
ST72325xx
2 PIN DESCRIPTION
Figure 2. 64-Pin LQFP 14x14 and 10x10 Package Pinout
(HS) PE4 (HS) PE5 (HS) PE6 (HS) PE7 PWM3 / PB0 PWM2 / PB1 PWM1 / PB2 PWM0 / PB3 ARTCLK / (HS) PB4 ARTIC1 / PB5 ARTIC2 / PB6 PB7 AIN0 / PD0 AIN1 / PD1 AIN2 / PD2 AIN3 / PD3
64 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
PE3 PE2 PE1 / RDI PE0 / TDO VDD_2 OSC1 OSC2 VSS_2 TLI EVD RESET VPP / ICCSEL PA7 (HS) / SCLI PA6 (HS) / SDAI PA5 (HS) PA4 (HS) 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 ei0 44 43 ei2 42 41 40 39 ei3 38 37 36 35 ei1 34 33 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
VSS_1 VDD_1 PA3 (HS) PA2 PA1 PA0 PC7 / SS / AIN15 PC6 / SCK / ICCCLK PC5 / MOSI / AIN14 PC4 / MISO / ICCDATA PC3 (HS) / ICAP1_B PC2 (HS) / ICAP2_B PC1 / OCMP1_B / AIN13 PC0 / OCMP2_B / AIN12 VSS_0 VDD_0
8/197
AIN4 / PD4 AIN5 / PD5 AIN6 / PD6 AIN7 / PD7 VAREF VSSA VDD_3 VSS_3 MCO / AIN8 / PF0 BEEP / (HS) PF1 (HS) PF2 OCMP2_A / AIN9 / PF3 OCMP1_A / AIN10 / PF4 ICAP2_A / AIN11 / PF5 ICAP1_A / (HS) PF6 EXTCLK_A / (HS) PF7 (HS) 20mA high sink capability eix associated external interrupt vector
ST72325xx
Figure 3. 48-Pin LQFP 7x7 Device Pinout
PE2 (HS) PE4 PWM3 / PB0 PWM2 / PB1 PWM1 / PB2 PWM0 / PB3 ARTCLK / (HS) PB4 ARTIC1 / PB5 AIN0 / PD0 AIN1 / PD1 AIN3 / PD2 AIN4 / PD3
48 47 46 45 44 43 42 41 40 39 38 37 36 1 2 35 3 34 ei2 33 4 32 5 ei0 31 6 ei3 30 7 29 8 28 9 27 10 26 11 ei1 25 12 13 14 15 16 17 18 19 20 21 22 23 24 AIN4 / PD4 AIN5 / PD5 VAREF VSSA MCO / AIN8 / PF0 BEEP / (HS) PF1 (HS) PF2 OCMP1_A / AIN10 / PF4 ICAP1_A / (HS) PF6 EXTCLK_A / (HS) PF7 VDD_0 VSS_0
PA7 (HS) / SCLI PA6 (HS) / SDAI PA5 (HS) PA4 (HS) VSS_1 VDD_1 PA3 (HS) PA2 PC7 / SS / AIN15 PC6 / SCK / ICCCLK PC5 / MOSI / AIN14 PC4 / MISO / ICCDATA PC3 (HS) / ICAP1_B PC2 (HS) / ICAP2_B PC1 / OCMP1_B / AIN13 PC0 / OCMP2_B / AIN12
Legend
PE1/ RDI PE0 / TDO VDD_2 OSC1 OSC2 VSS_2 RESET VPP/ICCSEL
= Pin not connected in ST72325S devices
(HS) 20mA high sink capability eix associated external interrupt vector
Caution: 48-pin `C' devices have unbonded pins that require software initialization. Refer
to Note 4 on page 16 for details on initializing the I/O registers for these devices.
9/197
ST72325xx
Figure 4. 44/42-Pin LQFP Package Pinouts
RDI / PE1 PB0 PB1 PB2 PB3 (HS) PB4 AIN0 / PD0 AIN1 / PD1 AIN2 / PD2 AIN3 / PD3 AIN4 / PD4
44 43 42 41 40 39 38 37 36 35 34 1 33 2 32 3 31 ei0 ei2 4 30 5 29 ei3 6 28 7 27 8 26 9 25 ei1 10 24 11 23 12 13 14 15 16 17 18 19 20 21 22 AIN5 / PD5 VAREF VSSA MCO / AIN8 / PF0 BEEP / (HS) PF1 (HS) PF2 OCMP1_A / AIN10 / PF4 ICAP1_A / (HS) PF6 EXTCLK_A / (HS) PF7 VDD_0 VSS_0
PE0 / TDO VDD_2 OSC1 OSC2 VSS_2 RESET VPP / ICCSEL PA7 (HS) / SCLI PA6 (HS) / SDAI PA5 (HS) PA4 (HS)
VSS_1 VDD_1 PA3 (HS) PC7 / SS / AIN15 PC6 / SCK / ICCCLK PC5 / MOSI / AIN14 PC4 / MISO / ICCDATA PC3 (HS) / ICAP1_B PC2 (HS) / ICAP2_B PC1 / OCMP1_B / AIN13 PC0 / OCMP2_B / AIN12
(HS) PB4 AIN0 / PD0 AIN1 / PD1 AIN2 / PD2 AIN3 / PD3 AIN4 / PD4 AIN5 / PD5 VAREF VSSA MCO / AIN8 / PF0 BEEP / (HS) PF1 (HS) PF2 AIN10 / OCMP1_A / PF4 ICAP1_A / (HS) PF6 EXTCLK_A / (HS) PF7 AIN12 / OCMP2_B / PC0 AIN13 / OCMP1_B / PC1 ICAP2_B/ (HS) PC2 ICAP1_B / (HS) PC3 ICCDATA / MISO / PC4 AIN14 / MOSI / PC5
1 ei3 2 3 4 5 6 7 8 9 10 11 ei1 12 13 14 15 16 17 18 19 20 21
ei2
ei0
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22
PB3 PB2 PB1 PB0 PE1 / RDI PE0 / TDO VDD_2 OSC1 OSC2 VSS_2 RESET VPP / ICCSEL PA7 (HS) / SCLI PA6 (HS) / SDAI PA5 (HS) PA4 (HS) VSS_1 VDD_1 PA3 (HS) PC7 / SS / AIN15 PC6 / SCK / ICCCLK (HS) 20mA high sink capability eix associated external interrupt vector
10/197
ST72325xx
Figure 5. 32-Pin LQFP/DIP Package Pinouts
PD1 / AIN1 PD0 / AIN0 PB4 (HS) / ARTCLK PB3 / PWM0 PB0 / PWM3 PE1 / RDI PE0 / TDO VDD_2 VAREF VSSA MCO / AIN8 / PF0 BEEP / (HS) PF1 OCMP1_A / AIN10 / PF4 ICAP1_A / (HS) PF6 EXTCLK_A / (HS) PF7 AIN12 / OCMP2_B / PC0 32 31 30 29 28 27 26 25 24 1 ei3 ei2 23 2 22 3 ei1 21 4 20 5 19 6 18 7 ei0 17 8 9 10 11 12 13 14 15 16 AIN13 / OCMP1_B / PC1 ICAP2_B / (HS) PC2 ICAP1_B / (HS) PC3 ICCDATA / MISO / PC4 AIN14 / MOSI / PC5 ICCCLK / SCK / PC6 AIN15 / SS / PC7 (HS) PA3
OSC1 OSC2 VSS_2 RESET VPP / ICCSEL PA7 (HS)/SCLI PA6 (HS) / SDAI PA4 (HS)
(HS) PB4 AIN0 / PD0 AIN1 / PD1 VAREF VSSA MCO / AIN8 / PF0 BEEP / (HS) PF1 OCMP1_A / AIN10 / PF4 ICAP1_A / (HS) PF6 EXTCLK_A / (HS) PF7 AIN12 / OCMP2_B / PC0 AIN13 / OCMP1_B / PC1 ICAP2_B / (HS) PC2 ICAP1_B / (HS) PC3 ICCDATA/ MISO / PC4 AIN14 / MOSI / PC5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
ei3
32 ei2 31 30 29 28
PB3 PB0 PE1 / RDI PE0 / TDO VDD_2 OSC1 OSC2 VSS_2 RESET VPP / ICCSEL PA7 (HS) / SCLI PA6 (HS) / SDAI PA4 (HS) PA3 (HS) PC7 / SS / AIN15 PC6 / SCK / ICCCLK (HS) 20mA high sink capability eix associated external interrupt vector
ei1
27 26 25 24 23 22 21 20 ei0 19 18 17
11/197
ST72325xx
PIN DESCRIPTION (Cont'd) For external pin connection guidelines, refer to See "ELECTRICAL CHARACTERISTICS" on page 142. Legend / Abbreviations for Table 2 and Table 3: Type: I = input, O = output, S = supply Input level: A = Dedicated analog input In/Output level: C = CMOS 0.3VDD/0.7VDD CT= CMOS 0.3VDD/0.7VDD with input trigger Output level: HS = 20mA high sink (on N-buffer only) Port and control configuration: Input: float = floating, wpu = weak pull-up, int = interrupt 1), ana = analog Output: OD = open drain 2), PP = push-pull Refer to "I/O PORTS" on page 50 for more details on the software configuration of the I/O ports. The RESET configuration of each pin is shown in bold. This configuration is valid as long as the device is in reset state. = Pin not connected in ST72325S devices
Table 2. LQFP64/48/44 and SDIP42 Device Pin Descriptions
Pin n LQFP48C LQFP48S LQFP64 LQFP44 Type SDIP42 Pin Name Level Output Input Port Input float w pu ana int Main O u t p u t function (after reset) OD X X X X PP X X X X Port E4 Port E5 Port E6 Port E7 PWM Output 3 5 3 3 2 39 PB0/PWM3 I/O CT I/O CT I/O CT I/O CT I/O CT HS I/O C T I/ O C T I/O CT I/O CT I/O C T I/O C T I/O CT X ei2 X X Port B0 Caution: Negative current injection not allowed on this pin PWM Output 2 PWM Output 1 PWM Output 0 PWM-ART External Clock PWM-ART Input Capture 1 PWM-ART Input Capture 2 ADC Analog Input 0 ADC Analog Input 1 ADC Analog Input 2 ADC Analog Input 3
Alternate function
1 2 3 4
2 -4) -4) 4)
-
-
-
PE4 (HS) PE5 (HS) PE6 (HS) PE7 (HS)
I/O CT HS I/O CT HS I/O CT HS I/O CT HS
XX XX XX XX
6 7 8 9 10 11 12 13 14 15 16
4 5 6 7 8 -4) -4) 9 19 11 12
4 5 6 7 9 10 11 12
3 4 5 6 7 8 9 10
40 41 42 1 2 3 4 5
PB1/PWM2 PB2/PWM1 PB3/PWM0 PB4 (HS)/ARTCLK PB5 / ARTIC1 PB6 / ARTIC2 PB 7 PD0/AIN0 PD1/AIN1 PD2/AIN2 PD3/AIN3
X X X X X X X
ei2 ei2 ei2 ei3 ei3 ei3 ei3 X X X X
X X X X X X X X X X X
X X X X X X X X X X X
Port B1 Port B2 Port B3 Port B4 Port B5 Port B6 Port B7 Port D0 Port D1 Port D2 Port D3
XX XX XX XX
12/197
ST72325xx
Pin n LQFP48C LQFP48S LQFP64 LQFP44 Type SDIP42 Pin Name
Level Output Input
Port Input float w pu ana int
OD
17 18 19 20 21 22 23 24 25 26 27 28
13 14 4)
13 14 15 16 17 18 19 -
11 12 13 14 15 16 17 -
6 7 8 9 10 11 12 -
PD4/AIN4 PD5/AIN5 PD6/AIN6 PD7/AIN7 VAREF6) VSSA6) VDD_36) VSS_36) PF0/MCO/AIN8 PF1 (HS)/BEEP PF2 (HS) PF3/OCM P2_A/ AIN9 PF4/OCM P1_A/ AIN10 PF5/ICA P2_A/ AIN11
I/O CT I/O CT I/O CT I/O CT I S S S I/O C T I/O C T H S I/O C T H S I/O CT
XX XX XX XX
X X X X
X X X X
PP
Main function Output (after reset) X X X X Port D4 Port D5 Port D6 Port D7
Alternate function
ADC Analog Input 4 ADC Analog Input 5 ADC Analog Input 6 ADC Analog Input 7
-4) 15 16 17 18 19 -4)
Analog Reference Voltage for ADC Analog Ground Voltage Digital Main Supply Voltage Digital Ground Voltage X X X XX ei1 ei1 ei1 X X X X X X X X X X Port F0 Port F1 Port F2 Port F3 Tim e r A Output Compare 2 Tim e r A Output Compare 1 Timer A Input Capture 2 ADC Analog Input 9 ADC Analog Input 10 ADC Analog Input 11 ADC AnaMain clock log out (fOSC/2) Input 8 Beep signal output
29
20
20
18
13
I/O CT
XX
X
X
X
Port F4
30 31 32 33 34 35
-4) 21 22 23 24 25
21 22 23 24 25
19 20 21 22 23
14 15 16
I/O CT
XX XX XX
X
X X X
X X X
Port F5 Port F6 Port F7
PF6 (HS)/ICAP1_A I/O CT HS PF7 (HS)/ EXTCLK_A VDD_06) VSS_0
6)
Timer A Input Capture 1 Timer A External Clock Source
I/O CT HS S S I/O CT
Digital Main Supply Voltage Digital Ground Voltage XX X X X Port C0 Tim e r B Output Compare 2 Tim e r B Output Compare 1 ADC Analog Input 12 ADC Analog Input 13
PC0/OCMP2_B/ AIN12 PC1/OCMP1_B/ AIN13
36 37 38 39
26 27 28 29
26 27 28 29
24 25 26 27
17 18 19 20
I/O CT
XX XX XX XX
X
X X X X
X X X X
Port C1 Port C2 Port C3 Port C4
PC2 (HS)/ICAP2_B I/O CT HS PC3 (HS)/ICAP1_B I/O CT HS PC4/MISO/ICCDATA PC5/MOSI/AIN14 PC6/SCK/ICCCLK I/O CT
Timer B Input Capture 2 Timer B Input Capture 1 SPI Master In / Slave Out Data SPI Master Out / Slave In Data SPI Serial Clock ICC Data Input ADC Analog Input 14 ICC Clock Output
40 41
30 31
30 31
28 29
21 22
I/O C T I/O C T
XX XX
X
X X
X X
Port C5 Port C6
13/197
ST72325xx
Pin n LQFP48C LQFP48S LQFP64 LQFP44 Type SDIP42 Pin Name
Level Output Input
Port Input float w pu ana int
OD
PP
Main function Output (after reset)
Alternate function
42 43 44 45 46 47 48 49 50 51 52
32 -4) -4) 33 34 35 36 37 38 39 40
32 34 35 36 37 38 39 40
30 31 32 33 34 35 36 37
23 24 25 26 27 28 29 30
PC7/SS/AIN15 PA 0 PA 1 PA 2 PA3 (HS) VDD_16) VSS_1
6)
I/ O C T I/O CT I/O CT I/O C T I/O C T H S S S I/O C T H S I/O C T H S I/O CT HS I/O CT HS
XX X X X X ei0 ei0 ei0 ei0
X
X X X X X
X X X X X
Port C7 Port A0 Port A1 Port A2 Port A3
SPI Slave Select (active low)
ADC Analog Input 15
Digital Main Supply Voltage Digital Ground Voltage XX XX X X X X T T X X Port A4 Port A5 Port A6 Port A7 I2C Data 1) I2C Clock 1)
PA4 (HS) PA5 (HS) PA6 (HS)/SDAI PA7 (HS)/SCLI
53
41
41
38
31
VPP/ ICCSEL
I
Must be tied low. In flash programming mode, this pin acts as the programming voltage input VPP. See Section 12.9.2 for more details. High voltage must not be applied to ROM devices Top priority non maskable interrupt. External voltage detector X Top level interrupt input pin Digital Ground Voltage Resonator oscillator inverter output External clock input or Resonator oscillator inverter input Digital Main Supply Voltage XX XX XX XX X X X X X X Port E0 Port E1 Port E3 SCI Transmit Data Out SCI Receive Data In
54 55 56 57 58 59 60 61 62 63 64
42 43 44 45 46 47 48 1 -4)
42 43 44 45 46 47 48 -
39 40 41 42 43 44 1 -
32 33 34 35 36 37 38 -
RE SET EV D TLI VSS_26) OSC23) OSC13) VDD_26) PE0/TDO PE1/RDI PE 2 PE 3
I/O CT
I S I/O I S
CT
I/O CT I/O C T I/O CT I/O CT
X4) X4) Port E2
14/197
ST72325xx
Table 3. LQFP32/DIP32 Device Pin Description
Pin n LQFP32 Type DIP32 Pin Name Level Output Input Input fl oat wpu ana int Port Main function Output (after reset) OD PP
Alternate function
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
VAREF6) VSSA
6)
I S I/O CT I / O CT I/O CT I / O CT I/O CT I/O CT I/O CT HS HS HS HS HS X X X X X X X X X X X X X HS HS HS HS X X X X X ei1 ei1 X X X X X X X X X X X ei0 X X X X X X X X X X X X X X X X X X X X X T T X X X X X X X X X X X X X X X
Analog Reference Voltage for ADC Analog Ground Voltage Port F0 Port F1 Port F4 Port F6 Port F7 Port C0 Port C1 Port C2 Port C3 Port C4 Port C5 Port C6 Port C7 Port A3 Port A4 Port A6 Port A7 I2C Data 1) I2C Clock 1) Main clock out (fOSC/2) Timer A Output Compare 1 ADC Analog Input 8 ADC Analog Input 10
PF0/MC O/AIN8 PF1 (HS)/BEEP PF4/OC MP1_A/ AIN10 PF6 (HS)/ICAP1_A PF7 (HS)/ EXTCLK_A PC0/O CMP2_B/ AIN12 PC1/O CMP1_B/ AIN13
Beep signal output
Timer A Input Capture 1 Timer A External Clock Source Timer B Output Compare 2 Timer B Output Compare 1 ADC Analog Input 12 ADC Analog Input 13
PC2 (HS)/ICAP2_B I/O CT PC3 (HS)/ICAP1_B I/O CT PC4/MISO/ICCDATA P C 5 / M OS I / A I N 1 4 PC6/SC K/ICCCLK P C 7 / S S /AI N 15 PA3 (HS) PA4 (HS) PA6 (HS)/SDAI PA7 (HS)/SCLI I/O CT I / O CT I/O CT I/ O C T I/O C T I/O C T I/O CT I/O CT
Timer B Input Capture 2 Timer B Input Capture 1 SPI Master In / Slave Out Data ICC Data Input
SPI Master Out / ADC Analog Slave In Data Input 14 SPI Serial Clock ICC Clock Output
SPI Slave Select ADC Analog (active low) Input 15
20
23
VPP/ ICCSEL
I
Must be tied low. In flash programming mode, this pin acts as the programming voltage input VPP. See Section 12.9.2 for more details. High voltage must not be applied to ROM devices Top priority non maskable interrupt. Digital Ground Voltage Resonator oscillator inverter output External clock input or Resonator oscillator inverter input Digital Main Supply Voltage X X X X X X X X Port E0 Port E1 SCI Transmit Data Out SCI Receive Data In
21 22 23 24 25 26 27
24 25 26 27 28 29 30
RESET VSS_2
6)
I/O CT S I/O I S I / O CT I / O CT
OSC2 3 ) OSC1 3 ) VDD_26) PE0/TDO PE1/RD I
15/197
ST72325xx
Pin n LQFP32 Type DIP32 Pin Name
Level Output Input Input fl oat wpu
Port
ana
OD
PP
int
Main function Output (after reset)
Alternate function
PWM Output 3 28 29 30 31 32 31 32 1 2 3 PB0/PW M3 P B 3 / P W M0 PB4 (HS)/ARTCLK PD0/AIN0 PD1/AIN1 I /O C T I/O CT I/O CT I/O CT I/O CT HS X X X X X X X ei2 ei2 ei3 X X X X X X X X X X X X Port B0 Port B3 Port B4 Port D0 Port D1 Caution: Negative current injection not allowed on this pin PWM Output 0 PWM-ART External Clock ADC Analog Input 0 ADC Analog Input 1
Notes for Table 2 and Table 3: 1. In the interrupt input column, "eiX" defines the associated external interrupt vector. If the weak pull-up column (wpu) is merged with the interrupt column (int), then the I/O configuration is pull-up interrupt input, else the configuration is floating interrupt input. 2. In the open drain output column, "T" defines a true open drain I/O (P-Buffer and protection diode to VDD are not implemented). See See "I/O PORTS" on page 50. and Section 12.8 I/O PORT PIN CHARACTERISTICS for more details. 3. OSC1 and OSC2 pins connect a crystal/ceramic resonator, or an external source to the on-chip oscillator; see Section 1 DESCRIPTION and Section 12.5 CLOCK AND TIMING CHARACTERISTICS for more details. 4. On the chip, each I/O port may have up to 8 pads: In all devices except 48-pin ST72325C, pads that are not bonded to external pins are forced by hardware in input pull-up configuration after reset. The configuration of these pads must be kept at reset state to avoid added current consumption. In 48-pin ST72325C devices, unbonded pads PA0, PA1, PB6, PB7, PD6, PD7, PE3, PE5, PE6, PE7, PF3 and PF5) are in input floating configuration after reset. To avoid added current consumption, the application must force these ports in input pull-up state by writing to the OR and DDR registers after reset. This initialization is not necessary in 48-pin ST72325S devices. 5. Pull-up always activated on PE2 see limitation Section 15.1.8. 6. It is mandatory to connect all available VDD and VREF pins to the supply voltage and all VSS and VSSA pins to ground.
16/197
ST72325xx
3 REGISTER & MEMORY MAP
As shown in Figure 6, the MCU is capable of addressing 64K bytes of memories and I/O registers. The available memory locations consist of 128 bytes of register locations, up to 2Kbytes of RAM and up to 60Kbytes of user program memory. The RAM space includes up to 256 bytes for the stack from 0100h to 01FFh. The highest address bytes contain the user reset and interrupt vectors. Figure 6. Memory Map
0000h 007Fh 0080h
IMPORTANT: Memory locations marked as "Reserved" must never be accessed. Accessing a reseved area can have unpredictable effects on the device. Related Documentation AN 985: Executing Code in ST7 RAM
HW Registers (see Table 4)
0080h
Short Addressing RAM (zero page)
00FFh 0100h
RA M (2048, 1536, 1024, or 512 Bytes)
087Fh 0880h
256 By tes S tac k
01FFh 0200h 1000h
Reserved
0FFFh 1000h
16-bit Addressing RA M
027Fh or 047Fh or 067Fh or 087Fh
60 KBytes 48 KBytes 32 KBytes 16 KBytes
4000h 8000h C000h
Program Memory (60,48, 32 or 16K)
FFDFh FFE0h FFFFh
Interrupt & Reset Vectors (see Table 9)
FFFFh
17/197
ST72325xx
Table 4. Hardware Register Map
Address 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0018h 0019h 001Ah 001Bh 001Ch 001Dh 001Eh 001Fh 0020h 0021h 0022h 0023h 0024h 0025h 0026h 0027h 0028h 0029h 002Ah 002Bh FLAS H W ATCHDOG SPIDR SPICR SPICSR ISPR0 ISPR1 ISPR2 ISPR3 EIC R FCSR WD G C R SIC SR Block Register Label PADR PADDR PAOR PBDR PBDDR PBOR PCDR PCDDR PCOR PDDR PDDDR PDOR PEDR PEDDR PEOR PFDR PFDDR PFOR I2CC R I2CS R1 I2CS R2 I2CC CR I2CO AR1 I2CO AR2 I2CD R Register Name Port A Data Register Port A Data Direction Register Port A Option Register Port B Data Register Port B Data Direction Register Port B Option Register Port C Data Register Port C Data Direction Register Port C Option Register Port D Data Register Port D Data Direction Register Port D Option Register Port E Data Register Port E Data Direction Register Port E Option Register Port F Data Register Port F Data Direction Register Port F Option Register I2C Control Register I2C Status Register 1 I2C Status Register 2 I2C Clock Control Register I2C Own Address Register 1 I2C Own Address Register2 I2C Data Register Reserved Area (2 Bytes) SPI Data I/O Register SPI Control Register SPI Control/Status Register Interrupt Software Priority Register 0 Interrupt Software Priority Register 1 Interrupt Software Priority Register 2 Interrupt Software Priority Register 3 External Interrupt Control Register Flash Control/Status Register Watchdog Control Register System Integrity Control/Status Register xxh 0xh 00h FFh FFh FFh FFh 00h 00h 7Fh R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Reset Status 00h1 ) 00h 00h 00h1 ) 00h 00h 00h1 ) 00h 00h 00h1 ) 00h 00h 00h1 ) 00h 00h 00h1 ) 00h 00h 00h 00h 00h 00h 00h 00h 00h Remarks R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R / W2 ) R / W2 ) R/W R/W R/W R/W Read Only Read Only R/W R/W R/W R/W
Port A
Port B
Port C
Port D
Port E
Port F
I 2C
SPI
ITC
000x 000x b R/W
18/197
ST72325xx
Address 002Ch 002Dh 002Eh to 0030h 0031h 0032h 0033h 0034h 0035h 0036h 0037h 0038h 0039h 003Ah 003Bh 003Ch 003Dh 003Eh 003Fh 0040h 0041h 0042h 0043h 0044h 0045h 0046h 0047h 0048h 0049h 004Ah 004Bh 004Ch 004Dh 004Eh 004Fh 0050h 0051h 0052h 0053h 0054h 0055h 0056h 0057h
Block
Register Label MCCS R MCCB CR
Register Name Main Clock Control / Status Register Main Clock Controller: Beep Control Register
Reset Status 00h 00h
Remarks R/W R/W
MC C
Reserved Area (3 Bytes)
TIME R A
TACR2 TACR1 TACSR TAIC1HR TAIC1LR TAOC1HR TAOC1LR TACHR TACLR TAACHR TAACLR TAIC2HR TAIC2LR TAOC2HR TAOC2LR
Timer A Control Register 2 Timer A Control Register 1 Timer A Control/Status Register Timer A Input Capture 1 High Register Timer A Input Capture 1 Low Register Timer A Output Compare 1 High Register Timer A Output Compare 1 Low Register Timer A Counter High Register Timer A Counter Low Register Timer A Alternate Counter High Register Timer A Alternate Counter Low Register Timer A Input Capture 2 High Register Timer A Input Capture 2 Low Register Timer A Output Compare 2 High Register Timer A Output Compare 2 Low Register Reserved Area (1 Byte)
00h 00h xxxx x0xx b xxh xxh 80h 00h FFh FCh FFh FCh xxh xxh 80h 00h
R/W R/W R/W Read Only Read Only R/W R/W Read Only Read Only Read Only Read Only Read Only Read Only R/W R/W
TIME R B
TBCR2 TBCR1 TBCSR TBIC1HR TBIC1LR TBOC1HR TBOC1LR TBCHR TBCLR TBACHR TBACLR TBIC2HR TBIC2LR TBOC2HR TBOC2LR SCISR SCIDR SCIBRR SCICR1 SCICR2 SCIERPR SCIETPR
Timer B Control Register 2 Timer B Control Register 1 Timer B Control/Status Register Timer B Input Capture 1 High Register Timer B Input Capture 1 Low Register Timer B Output Compare 1 High Register Timer B Output Compare 1 Low Register Timer B Counter High Register Timer B Counter Low Register Timer B Alternate Counter High Register Timer B Alternate Counter Low Register Timer B Input Capture 2 High Register Timer B Input Capture 2 Low Register Timer B Output Compare 2 High Register Timer B Output Compare 2 Low Register SCI Status Register SCI Data Register SCI Baud Rate Register SCI Control Register 1 SCI Control Register 2 SCI Extended Receive Prescaler Register Reserved area SCI Extended Transmit Prescaler Register
00h 00h xxxx x0xx b xxh xxh 80h 00h FFh FCh FFh FCh xxh xxh 80h 00h C0h xxh 00h x000 0000b 00h 00h --00h
R/W R/W R/W Read Only Read Only R/W R/W Read Only Read Only Read Only Read Only Read Only Read Only R/W R/W Read Only R/W R/W R/W R/W R/W R/W
SCI
19/197
ST72325xx
Address 0058h 0059h 005Ah 005Bh 005Ch 005Dh 005Eh to 006Fh 0070h 0071h 0072h 0073h 0074h 0075h 0076h 0077h 0078h 0079h 007Ah 007Bh 007Ch 007Dh 007Eh 007Fh
Block
Register Label DMCR DMSR DMBK1H DMBK1L DMBK2H DMBK2L
Register Name DM Control Register DM Status Register DM Breakpoint Register 1 High DM Breakpoint Register 1 Low DM Breakpoint Register 2 High DM Breakpoint Register 2 Low
Reset Status 00h 00h 00h 00h 00h 00h
Remarks R/W R/W R/W R/W R/W R/W
D M3 )
Reserved Area (18 Bytes)
AD C
ADCCSR ADCDRH ADCDRL PWMDCR3 PWM DCR2 PWM DCR1 PWM DCR0 PWM C R ARTCSR ARTCAR ARTARR ARTICCSR ARTICR1 ARTICR2
Control/Status Register Data High Register Data Low Register PWM AR Timer Duty Cycle Register 3 PWM AR Timer Duty Cycle Register 2 PWM AR Timer Duty Cycle Register 1 PWM AR Timer Duty Cycle Register 0 PWM AR Timer Control Register Auto-Reload Timer Control/Status Register Auto-Reload Timer Counter Access Register Auto-Reload Timer Auto-Reload Register AR Timer Input Capture Control/Status Reg. AR Timer Input Capture Register 1 AR Timer Input Capture Register 1 Reserved Area (2 Bytes)
00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h
R/W Read Only Read Only R/W R/W R/W R/W R/W R/W R/W R/W R/W Read Only Read Only
PWM ART
Legend: x=undefined, R/W=read/write Notes: 1. The contents of the I/O port DR registers are readable only in output configuration. In input configuration, the values of the I/O pins are returned instead of the DR register contents. 2. The bits associated with unavailable pins must always keep their reset value. 3. For a description of the Debug Module registers, see ICC Protocol Reference manual.
20/197
ST72325xx
4 FLASH PROGRAM MEMORY
4.1 Introduction The ST7 dual voltage High Density Flash (HDFlash) is a non-volatile memory that can be electrically erased as a single block or by individual sectors and programmed on a Byte-by-Byte basis using an external VPP supply. The HDFlash devices can be programmed and erased off-board (plugged in a programming tool) or on-board using ICP (In-Circuit Programming) or IAP (In-Application Programming). The array matrix organisation allows each sector to be erased and reprogrammed without affecting other sectors. 4.2 Main Features
Depending on the overall Flash memory size in the microcontroller device, there are up to three user sectors (see Table 5). Each of these sectors can be erased independently to avoid unnecessary erasing of the whole Flash memory when only a partial erasing is required. The first two sectors have a fixed size of 4 Kbytes (see Figure 7). They are mapped in the upper part of the ST7 addressing space so the reset and interrupt vectors are located in Sector 0 (F000hFFFFh). Table 5. Sectors available in Flash devices
Flash Size (bytes) 4K 8K > 8K Available Sectors Sector 0 Sectors 0,1 Sectors 0,1, 2
Three Flash programming modes: Insertion in a programming tool. In this mode, all sectors including option bytes can be programmed or erased. ICP (In-Circuit Programming). In this mode, all sectors including option bytes can be programmed or erased without removing the device from the application board. IAP (In-Application Programming) In this mode, all sectors except Sector 0, can be programmed or erased without removing the device from the application board and while the application is running. ICT (In-Circuit Testing) for downloading and executing user application test patterns in RAM Read-out protection Register Access Security System (RASS) to prevent accidental programming or erasing
4.3 Structure The Flash memory is organised in sectors and can be used for both code and data storage.
4.3.1 Read-out Protection Read-out protection, when selected, provides a protection against Program Memory content extraction and against write access to Flash memory. Even if no protection can be considered as totally unbreakable, the feature provides a very high level of protection for a general purpose microcontroller. In flash devices, this protection is removed by reprogramming the option. In this case, the entire program memory is first automatically erased and the device can be reprogrammed. Read-out protection selection depends on the device type: In Flash devices it is enabled and removed through the FMP_R bit in the option byte. In ROM devices it is enabled by mask option specified in the Option List.
Figure 7. Memory Map and Sector Address
4K
1000h 3FFFh 7FFFh 9FFFh BFFFh D7FFh DFFFh EFFFh FFFFh
8K
10K
16K
24K
32K
48K
60K
FLASH MEMORY SIZE
SECTOR 2 2 Kbytes 8 Kbytes 16 Kbytes 24 Kbytes 40 Kbytes 52 Kbytes 4 Kbytes 4 Kbytes SECTOR 1 SECTOR 0
21/197
ST72325xx
FLASH PROGRAM MEMORY (Cont'd) 4.4 ICC Interface ICC needs a minimum of 4 and up to 6 pins to be connected to the programming tool (see Figure 8). These pins are: RESET: device reset VSS: device power supply ground Figure 8. Typical ICC Interface
PROGRAMMING TOOL ICC CONNECTOR ICC Cable APPLICATION BOARD (See Note 3) OPTIONAL (See Note 4) ICC CONNECTOR HE10 CONNECTOR TYPE 9 10 7 8 5 6 3 4 1 2 APPLICATION RESET SOURCE See Note 2 10k APPLICATION POWER SUPPLY CL2 CL1 See Note 1 APPLICATION I/O
ICCCLK: ICC output serial clock pin ICCDATA: ICC input/output serial data pin ICCSEL/VPP: programming voltage OSC1(or OSCIN): main clock input for external source (optional) VDD: application board power supply (optional, see Figure 8, Note 3)
ST7
Notes: 1. If the ICCCLK or ICCDATA pins are only used as outputs in the application, no signal isolation is necessary. As soon as the Programming Tool is plugged to the board, even if an ICC session is not in progress, the ICCCLK and ICCDATA pins are not available for the application. If they are used as inputs by the application, isolation such as a serial resistor has to implemented in case another device forces the signal. Refer to the Programming Tool documentation for recommended resistor values. 2. During the ICC session, the programming tool must control the RESET pin. This can lead to conflicts between the programming tool and the application reset circuit if it drives more than 5mA at high level (push pull output or pull-up resistor<1K). A schottky diode can be used to isolate the application RESET circuit in this case. When using a classical RC network with R>1K or a reset man-
agement IC with open drain output and pull-up resistor>1K, no additional components are needed. In all cases the user must ensure that no external reset is generated by the application during the ICC session. 3. The use of Pin 7 of the ICC connector depends on the Programming Tool architecture. This pin must be connected when using most ST Programming Tools (it is used to monitor the application power supply). Please refer to the Programming Tool manual. 4. Pin 9 has to be connected to the OSC1 or OSCIN pin of the ST7 when the clock is not available in the application or if the selected clock option is not programmed in the option byte. ST7 devices with multi-oscillator capability need to have OSC2 grounded in this case.
22/197
ICCSEL/VPP
ICCDATA
RESET
ICCCLK
OSC2
OSC1
VDD
VSS
ST72325xx
FLASH PROGRAM MEMORY (Cont'd) 4.5 ICP (In-Circuit Programming) To perform ICP the microcontroller must be switched to ICC (In-Circuit Communication) mode by an external controller or programming tool. Depending on the ICP code downloaded in RAM, Flash memory programming can be fully customized (number of bytes to program, program locations, or selection serial communication interface for downloading). When using an STMicroelectronics or third-party programming tool that supports ICP and the specific microcontroller device, the user needs only to implement the ICP hardware interface on the application board (see Figure 8). For more details on the pin locations, refer to the device pinout description. 4.6 IAP (In-Application Programming) This mode uses a BootLoader program previously stored in Sector 0 by the user (in ICP mode or by plugging the device in a programming tool). This mode is fully controlled by user software. This allows it to be adapted to the user application, (user-defined strategy for entering programming mode, choice of communications protocol used to fetch the data to be stored, etc.). For example, it is possible to download code from the SPI, SCI, USB or CAN interface and program it in the Flash. IAP mode can be used to program any of the Flash sectors except Sector 0, which is write/erase protected to allow recovery in case errors occur during the programming operation. 4.7 Related Documentation For details on Flash programming and ICC protocol, refer to the ST7 Flash Programming Reference Manual and to the ST7 ICC Protocol Reference Manual. 4.7.1 Register Description FLASH CONTROL/STATUS REGISTER (FCSR) Read / Write Reset Value: 0000 0000 (00h)
7 0 0 0 0 0 0 0 0 0
This register is reserved for use by Programming Tool software. It controls the Flash programming and erasing operations.
Figure 9. Flash Control/Status Register Address and Reset Value
Address (Hex.) 0029h Register Label FC SR Reset Value 7 6 5 4 3 2 1 0
0
0
0
0
0
0
0
0
23/197
ST72325xx
5 CENTRAL PROCESSING UNIT
5.1 INTRODUCTION This CPU has a full 8-bit architecture and contains six internal registers allowing efficient 8-bit data manipulation. 5.2 MAIN FEATURES
5.3 CPU REGISTERS The six CPU registers shown in Figure 1 are not present in the memory mapping and are accessed by specific instructions. Accumulator (A) The Accumulator is an 8-bit general purpose register used to hold operands and the results of the arithmetic and logic calculations and to manipulate data. Index Registers (X and Y) These 8-bit registers are used to create effective addresses or as temporary storage areas for data manipulation. (The Cross-Assembler generates a precede instruction (PRE) to indicate that the following instruction refers to the Y register.) The Y register is not affected by the interrupt automatic procedures. Program Counter (PC) The program counter is a 16-bit register containing the address of the next instruction to be executed by the CPU. It is made of two 8-bit registers PCL (Program Counter Low which is the LSB) and PCH (Program Counter High which is the MSB).
Enable executing 63 basic instructions Fast 8-bit by 8-bit multiply 17 main addressing modes (with indirect addressing mode) Two 8-bit index registers 16-bit stack pointer Low power HALT and WAIT modes Priority maskable hardware interrupts Non-maskable software/hardware interrupts
Figure 10. CPU Registers
7 RESET VALUE = XXh 7 RESET VALUE = XXh 7 RESET VALUE = XXh 15 PCH 87 PCL 0 PROGRAM COUNTER RESET VALUE = RESET VECTOR @ FFFEh-FFFFh 7 0 CONDITION CODE REGISTER 1 1 I1 H I0 N Z C RESET VALUE = 1 1 1 X 1 X X X 15 87 0 STACK POINTER RESET VALUE = STACK HIGHER ADDRESS X = Undefined Value 0 Y INDEX REGISTER 0 X INDEX REGISTER 0 ACCUMULATOR
24/197
ST72325xx
CENTRAL PROCESSING UNIT (Cont'd) Condition Code Register (CC) Read/Write Reset Value: 111x1xxx
7
1 1 I1 H I0 N Z
Bit 1 = Z Zero. This bit is set and cleared by hardware. This bit indicates that the result of the last arithmetic, logical or data manipulation is zero. 0: The result of the last operation is different from zero. 1: The result of the last operation is zero. This bit is accessed by the JREQ and JRNE test inst ructions. Bit 0 = C Carry/borrow. This bit is set and cleared by hardware and software. It indicates an overflow or an underflow has occurred during the last arithmetic operation. 0: No overflow or underflow has occurred. 1: An overflow or underflow has occurred. This bit is driven by the SCF and RCF instructions and tested by the JRC and JRNC instructions. It is also affected by the "bit test and branch", shift and rotate instructions. Interrupt Management Bits Bit 5,3 = I1, I0 Interrupt The combination of the I1 and I0 bits gives the current interrupt software priority.
Interrupt Software Priority Level 0 (main) Level 1 Level 2 Level 3 (= interrupt disable) I1 1 0 0 1 I0 0 1 0 1
0 C
The 8-bit Condition Code register contains the interrupt masks and four flags representative of the result of the instruction just executed. This register can also be handled by the PUSH and POP instructions. These bits can be individually tested and/or controlled by specific instructions. Arithmetic Management Bits Bit 4 = H Half carry. This bit is set by hardware when a carry occurs between bits 3 and 4 of the ALU during an ADD or ADC instructions. It is reset by hardware during the same instructions. 0: No half carry has occurred. 1: A half carry has occurred. This bit is tested using the JRH or JRNH instruction. The H bit is useful in BCD arithmetic subroutines. Bit 2 = N Negative. This bit is set and cleared by hardware. It is representative of the result sign of the last arithmetic, logical or data manipulation. It's a copy of the result 7th bit. 0: The result of the last operation is positive or null. 1: The result of the last operation is negative (that is, the most significant bit is a logic 1). This bit is accessed by the JRMI and JRPL instructions.
These two bits are set/cleared by hardware when entering in interrupt. The loaded value is given by the corresponding bits in the interrupt software priority registers (IxSPR). They can be also set/ cleared by software with the RIM, SIM, IRET, HALT, WFI and PUSH/POP instructions. See the interrupt management chapter for more details.
25/197
ST72325xx
CENTRAL PROCESSING UNIT (Cont'd) Stack Pointer (SP) Read/Write Reset Value: 01 FFh
15 0 7
SP7 SP6 SP5 SP4 SP3 SP2 SP1
8 0 0 0 0 0 0 1 0 SP0
The Stack Pointer is a 16-bit register which is always pointing to the next free location in the stack. It is then decremented after data has been pushed onto the stack and incremented before data is popped from the stack (see Figure 2). Since the stack is 256 bytes deep, the 8 most significant bits are forced by hardware. Following an MCU Reset, or after a Reset Stack Pointer instruction (RSP), the Stack Pointer contains its reset value (the SP7 to SP0 bits are set) which is the stack higher address. Figure 11. Stack Manipulation Example
CALL Subroutine @ 0100h Interrupt Event P USH Y
The least significant byte of the Stack Pointer (called S) can be directly accessed by a LD instruction. Note: When the lower limit is exceeded, the Stack Pointer wraps around to the stack upper limit, without indicating the stack overflow. The previously stored information is then overwritten and therefore lost. The stack also wraps in case of an underflow. The stack is used to save the return address during a subroutine call and the CPU context during an interrupt. The user may also directly manipulate the stack by means of the PUSH and POP instructions. In the case of an interrupt, the PCL is stored at the first location pointed to by the SP. Then the other registers are stored in the next locations as shown in Figure 2. When an interrupt is received, the SP is decremented and the context is pushed on the stack. On return from interrupt, the SP is incremented and the context is popped from the stack. A subroutine call occupies two locations and an interrupt five locations in the stack area.
PO P Y
IRET
RET or RSP
SP SP CC A X PC H SP PCH @ 01FFh PCL P CL PCH PCL Y CC A X PCH PCL PCH PC L SP CC A X PCH PCL PCH PCL SP PCH PCL SP
Stack Higher Address = 01FFh Stack Lower Address = 0100h
26/197
ST72325xx
6 SUPPLY, RESET AND CLOCK MANAGEMENT
The device includes a range of utility features for securing the application in critical situations (for example in case of a power brown-out), and reducing the number of external components. An overview is shown in Figure 13. For more details, refer to dedicated parametric section. Main features Optional PLL for multiplying the frequency by 2 (not to be used with internal RC oscillator) Reset Sequence Manager (RSM) Multi-Oscillator Clock Management (MO) 5 Crystal/Ceramic resonator oscillators 1 Internal RC oscillator System Integrity Management (SI) Main supply Low voltage detection (LVD) Auxiliary Voltage detector (AVD) with interrupt capability for monitoring the main supply Clock Security System (CSS) with Clock Filter and Backup Safe Oscillator (enabled by option byte) Figure 13. Clock, Reset and Supply Block Diagram
SYSTEM INTEGRITY MANAGEMENT CLOCK SECURITY SYSTEM (CSS) OSC2 OSC1 MULTIOSCILLATOR (MO) fOSC PLL (option) fOSC2 CLOCK FILTER SAFE OSC fOSC2 MAIN CLOCK fCPU CONTROLLER WITH REALTIME CLOCK (MCC/RTC)
6.1 PHASE LOCKED LOOP If the clock frequency input to the PLL is in the range 2 to 4 MHz, the PLL can be used to multiply the frequency by two to obtain an fOSC2 of 4 to 8 MHz. The PLL is enabled by option byte. If the PLL is disabled, then fOSC2 = fOSC/2. Caution: The PLL is not recommended for applications where timing accuracy is required. See "PLL Characteristics" on page 154. Figure 12. PLL Block Diagram
PLL x 2
fOSC 0 fOSC2 1
/2
PLL OPTION BIT
RESET SEQUENCE RESET MANAGER (RSM)
AVD Interrupt Request SICSR AVD AVD AVD LVD S IE F RF CSS CSS WDG IE D RF
WATCHDOG TIMER (WDG)
0
CSS Interrupt Request LOW VOLTAGE VSS VDD 0 EVD 1 DETECTOR (LVD)
AUXILIARY VOLTAGE DETECTOR (AVD)
27/197
ST72325xx
6.2 MULTI-OSCILLATOR (MO) The main clock of the ST7 can be generated by three different source types coming from the multioscillator block: an external source 4 crystal or ceramic resonator oscillators an internal high frequency RC oscillator Each oscillator is optimized for a given frequency range in terms of consumption and is selectable through the option byte. The associated hardware configurations are shown in Table 6. Refer to the electrical characteristics section for more details. External Clock Source In this external clock mode, a clock signal (square, sinus or triangle) with ~50% duty cycle has to drive the OSC1 pin while the OSC2 pin is tied to ground. Crystal/Ceramic Oscillators This family of oscillators has the advantage of producing a very accurate rate on the main clock of the ST7. The selection within a list of 4 oscillators with different frequency ranges has to be done by option byte in order to reduce consumption (refer to section 14.1 on page 181 for more details on the frequency ranges). In this mode of the multi-oscillator, the resonator and the load capacitors have to be placed as close as possible to the oscillator pins in order to minimize output distortion and start-up stabilization time. The loading capacitance values must be adjusted according to the selected oscillator. These oscillators are not stopped during the RESET phase to avoid losing time in the oscillator start-up phase. Internal RC Oscillator This oscillator allows a low cost solution for the main clock of the ST7 using only an internal resistor and capacitor. Internal RC oscillator mode has the drawback of a lower frequency accuracy and should not be used in applications that require accurate timing. In this mode, the two oscillator pins have to be tied to ground. Table 6. ST7 Clock Sources
Hardware Configuration
External Clock
ST7 OS C1 OSC 2
EX TERNAL SO URCE
Crystal/Ceramic Resonators
ST7 OSC 1 OSC2
CL1
LOA D CAPA CITO RS
CL 2
Internal RC Oscillator
ST7 OSC1 OSC2
28/197
ST72325xx
6.3 RESET SEQUENCE MANAGER (RSM) 6.3.1 Introduction The reset sequence manager includes three RESET sources as shown in Figure 15: External RESET source pulse Internal LVD RESET (Low Voltage Detection) Internal WATCHDOG RESET These sources act on the RESET pin and it is always kept low during the delay phase. The RESET service routine vector is fixed at addresses FFFEh-FFFFh in the ST7 memory map. The basic RESET sequence consists of 3 phases as shown in Figure 14: Active Phase depending on the RESET source 256 or 4096 CPU clock cycle delay (selected by option byte) RESET vector fetch The 256 or 4096 CPU clock cycle delay allows the oscillator to stabilise and ensures that recovery has taken place from the Reset state. The shorter or longer clock cycle delay should be selected by option byte to correspond to the stabilization time of the external oscillator used in the application (see section 14.1 on page 181). The RESET vector fetch phase duration is 2 clock c ycles. Figure 15. Reset Block Diagram Figure 14. RESET Sequence Phases
RESET
Active Phase INTERNAL RESET 256 or 4096 CLOCK CYCLES FETCH VECTOR
Caution: When the ST7 is unprogrammed or fully erased, the Flash is blank and the RESET vector is not programmed. For this reason, it is recommended to keep the RESET pin in low state until programming mode is entered, in order to avoid unwanted behavior. 6.3.2 Asynchronous External RESET pin The RESET pin is both an input and an open-drain output with integrated RON weak pull-up resistor. This pull-up has no fixed value but varies in accordance with the input voltage. It can be pulled low by external circuitry to reset the device. See "CONTROL PIN CHARACTERISTICS" on page 162 for more details. A RESET signal originating from an external source must have a duration of at least th(RSTL)in in order to be recognized (see Figure 16). This detection is asynchronous and therefore the MCU can enter reset state even in HALT mode.
VDD
RO N
RESET
Filter INTERNAL RESET
PULSE GENERATOR
WATCHDOG RESET LVD RESET
29/197
ST72325xx
RESET SEQUENCE MANAGER (Cont'd) The RESET pin is an asynchronous signal which plays a major role in EMS performance. In a noisy environment, it is recommended to follow the guidelines mentioned in the electrical characteristics section. If the external RESET pulse is shorter than tw(RSTL)out (see short ext. Reset in Figure 16), the signal on the RESET pin may be stretched. Otherwise the delay will not be applied (see long ext. Reset in Figure 16). Starting from the external RESET pulse recognition, the device RESET pin acts as an output that is pulled low during at least tw(RSTL)out. 6.3.3 External Power-On RESET If the LVD is disabled by option byte, to start up the microcontroller correctly, the user must ensure by means of an external reset circuit that the reset signal is held low until VDD is over the minimum level specified for the selected fOSC frequency. (see "OPERATING CONDITIONS" on page 144) A proper reset signal for a slow rising VDD supply can generally be provided by an external RC network connected to the RESET pin. 6.3.4 Internal Low Voltage Detector (LVD) R ESET Two different RESET sequences caused by the internal LVD circuitry can be distinguished: Power-On RESET Voltage Drop RESET The device RESET pin acts as an output that is pulled low when VDD
Figure 16. RESET Sequences VDD
VIT+(LVD) VIT-(LVD)
LVD RESET
SHORT EXT. RESET
LONG EXT. RESET
WATCHDOG RESET
RUN
ACTIVE PHASE
RUN
ACTIVE PHASE
RUN
ACTIVE PHASE
RUN
ACTIVE PHASE
RUN
tw(RSTL)out th(RSTL)in
EXTERNAL RESET SOURCE
tw(RSTL)out th(RSTL)in
DELAY
tw(RSTL)out
RESET PIN
WATCHDOG RESET WATCHDOG UNDERFLOW INTERNAL RESET (256 or 4096 TCPU) VECTOR FETCH
30/197
ST72325xx
6.4 SYSTEM INTEGRITY MANAGEMENT (SI) The System Integrity Management block contains the Low Voltage Detector (LVD) Auxiliary Voltage Detector (AVD) functions and Clock Security System (CSS). It is managed by the SICSR register. 6.4.1 Low Voltage Detector (LVD) The Low Voltage Detector function (LVD) generates a static reset when the VDD supply voltage is below a VIT- reference value. This means that it secures the power-up as well as the power-down keeping the ST7 in reset. The VIT- reference value for a voltage drop is lower than the VIT+ reference value for power-on in order to avoid a parasitic reset when the MCU starts running and sinks current on the supply (hysteresis). The LVD Reset circuitry generates a reset when VDD is below: VIT+ when VDD is rising VIT- when VDD is falling The LVD function is illustrated in Figure 17. The voltage threshold can be configured by option byte to be low, medium or high. Provided the minimum VDD value (guaranteed for the oscillator frequency) is above VIT-, the MCU can only be in two modes: Figure 17. Low Voltage Detector vs Reset
VDD
under full software control in static safe reset In these conditions, secure operation is always ensured for the application without the need for external reset hardware. During a Low Voltage Detector Reset, the RESET pin is held low, thus permitting the MCU to reset other devices. Notes: The LVD allows the device to be used without any external RESET circuitry. If the medium or low thresholds are selected, the detection may occur outside the specified operating voltage range. Below 3.8V, device operation is not guaranteed. The LVD is an optional function which can be selected by option byte. It is recommended to make sure that the VDD supply voltage rises monotonously when the device is exiting from Reset, to ensure the application functions properly.
Vhys VIT+ VIT-
RESET
31/197
ST72325xx
SYSTEM INTEGRITY MANAGEMENT (Cont'd) 6.4.2 Auxiliary Voltage Detector (AVD) The Voltage Detector function (AVD) is based on an analog comparison between a VIT-(AVD) and VIT+(AVD) reference value and the VDD main supply or the external EVD pin voltage level (VEVD). The VIT- reference value for falling voltage is lower than the VIT+ reference value for rising voltage in order to avoid parasitic detection (hysteresis). The output of the AVD comparator is directly readable by the application software through a real time status bit (AVDF) in the SICSR register. This bit is read only. Caution: The AVD function is active only if the LVD is enabled through the option byte. 6.4.2.1 Monitoring the VDD Main Supply This mode is selected by clearing the AVDS bit in the SICSR register. The AVD voltage threshold value is relative to the selected LVD threshold configured by option byte (see section 14.1 on page 181). If the AVD interrupt is enabled, an interrupt is generated when the voltage crosses the VIT+(AVD) or VIT-(AVD) threshold (AVDF bit toggles). In the case of a drop in voltage, the AVD interrupt acts as an early warning, allowing software to shut down safely before the LVD resets the microcontroller. See Figure 18. The interrupt on the rising edge is used to inform the application that the VDD warning state is over. If the voltage rise time trv is less than 256 or 4096 CPU cycles (depending on the reset delay selected by option byte), no AVD interrupt will be generated when VIT+(AVD) is reached. If trv is greater than 256 or 4096 cycles then: If the AVD interrupt is enabled before the VIT+(AVD) threshold is reached, then 2 AVD interrupts will be received: the first when the AVDIE bit is set, and the second when the threshold is reached. If the AVD interrupt is enabled after the VIT+(AVD) threshold is reached then only one AVD interrupt will occur.
Figure 18. Using the AVD to Monitor VDD (AVDS bit=0) VDD Early Warning Interrupt (Power has dropped, MCU not not yet in reset)
Vh y s t
VIT+(AVD) VIT-(AVD) VIT+(LVD) VIT-(LVD)
trv VOLTAGE RISE TIME
AVDF bit AVD INTERRUPT REQUES T IF AVDIE bit = 1
0
1
RESET VALUE
1
0
INTERRUPT PROCESS
INTERRUPT PROCESS
LVD RESET
32/197
ST72325xx
SYSTEM INTEGRITY MANAGEMENT (Cont'd) 6.4.2.2 Monitoring a Voltage on the EVD pin This mode is selected by setting the AVDS bit in the SICSR register. The AVD circuitry can generate an interrupt when the AVDIE bit of the SICSR register is set. This interrupt is generated on the rising and falling edges of the comparator output. This means it is generated when either one of these two events occur: VEVD rises up to VIT+(EVD) VEVD falls down to VIT-(EVD) The EVD function is illustrated in Figure 19. For more details, refer to the Electrical Characteristics section.
Figure 19. Using the Voltage Detector to Monitor the EVD pin (AVDS bit=1) VEVD
VIT+(EVD) VIT-(EVD)
Vh y s t
AVDF AVD INTERRUPT REQUES T IF AVDIE = 1
0
1
0
INTERRUPT PROCESS
INTERRUPT PROCESS
33/197
ST72325xx
SYSTEM INTEGRITY MANAGEMENT (Cont'd) 6.4.3 Clock Security System (CSS) The Clock Security System (CSS) protects the ST7 against breakdowns, spikes and overfrequencies occurring on the main clock source (fOSC). It is based on a clock filter and a clock detection control with an internal safe oscillator (fSFOSC). 6.4.3.1 Clock Filter Control The PLL has an integrated glitch filtering capability making it possible to protect the internal clock from overfrequencies created by individual spikes. This feature is available only when the PLL is enabled. If glitches occur on fOSC (for example, due to loose connection or noise), the CSS filters these automatically, so the internal CPU frequency (fCPU) continues deliver a glitch-free signal (see Figure 20). 6.4.3.2 Clock detection Control If the clock signal disappears (due to a broken or disconnected resonator...), the safe oscillator delivers a low frequency clock signal (fSFOSC) which allows the ST7 to perform some rescue operations. Automatically, the ST7 clock source switches back from the safe oscillator (fSFOSC) if the main clock source (fOSC) recovers. When the internal clock (fCPU) is driven by the safe oscillator (fSFOSC), the application software is notified by hardware setting the CSSD bit in the SICSR register. An interrupt can be generated if the Figure 20. Clock Filter Function
Clock Filter Function
fOSC2 fCPU
CSSIE bit has been previously set. These two bits are described in the SICSR register d e s c r i p t io n . 6.4.4 Low Power Modes
Mode WAIT Description No effect on SI. CSS and AVD interrupts cause the device to exit from Wait mode. The SICSR register is frozen.The CSS (including the safe oscillator) is disabled until HALT mode is exited. The previous CSS configuration resumes when the MCU is woken up by an interrupt with "exit from HALT mode" capability or from the counter reset value when the MCU is woken up by a RESET.
H AL T
6.4.4.1 Interrupts The CSS orAVD interrupt events generate an interrupt if the corresponding Enable Control Bit (CSSIE or AVDIE) is set and the interrupt mask in the CC register is reset (RIM instruction).
Interrupt Event Enable Event Control Flag Bit C SSIE A VDIE Exit from Wait Yes Yes Exit from Halt No No
CSS event detection (safe oscillator acti- CSSD vated as main clock) AVD event AVDF
Clock Detection Function
fOSC2 fSFOSC fCPU
34/197
PLL ON
ST72325xx
SYSTEM INTEGRITY MANAGEMENT (Cont'd) 6.4.5 Register Description SYSTEM INTEGRITY (SI) CONTROL/STATUS REGISTER (SICSR) Read / Write is detected by the Clock Security System (CSSD bit set). It is set and cleared by software. Reset Value: 000x 000x (00h) 0: Clock security system interrupt disabled 1: Clock security system interrupt enabled 7 0 When the CSS is disabled by OPTION BYTE, the CSSIE bit has no effect. A VD AVD A VD LVD C S S C S S WDG
S IE F RF 0 IE D RF
Bit 7 = AVDS Voltage Detection selection This bit is set and cleared by software. Voltage Detection is available only if the LVD is enabled by option byte. 0: Voltage detection on VDD supply 1: Voltage detection on EVD pin Bit 6 = AVDIE Voltage Detector interrupt enable This bit is set and cleared by software. It enables an interrupt to be generated when the AVDF flag changes (toggles). The pending interrupt information is automatically cleared when software enters the AVD interrupt routine. 0: AVD interrupt disabled 1: AVD interrupt enabled Bit 5 = AVDF Voltage Detector flag This read-only bit is set and cleared by hardware. If the AVDIE bit is set, an interrupt request is generated when the AVDF bit changes value. Refer to Figure 18 and to Section 6.4.2.1 for additional details . 0: VDD or VEVD over VIT+(AVD) threshold 1: VDD or VEVD under VIT-(AVD) threshold Bit 4 = LVDRF LVD reset flag This bit indicates that the last Reset was generated by the LVD block. It is set by hardware (LVD reset) and cleared by software (writing zero). See WDGRF flag description for more details. When the LVD is disabled by OPTION BYTE, the LVDRF bit value is undefined. Bit 3 = Reserved, must be kept cleared. Bit 2 = CSSIE Clock security syst. interrupt enable This bit enables the interrupt when a disturbance
Bit 1 = CSSD Clock security system detection This bit indicates that the safe oscillator of the Clock Security System block has been selected by hardware due to a disturbance on the main clock signal (fOSC). It is set by hardware and cleared by reading the SICSR register when the original oscillator recovers. 0: Safe oscillator is not active 1: Safe oscillator has been activated When the CSS is disabled by OPTION BYTE, the CSSD bit value is forced to 0. Bit 0 = WDGRF Watchdog reset flag This bit indicates that the last Reset was generated by the Watchdog peripheral. It is set by hardware (watchdog reset) and cleared by software (writing zero) or an LVD Reset (to ensure a stable cleared state of the WDGRF flag when CPU starts). Combined with the LVDRF flag information, the flag description is given by the following table.
RESET Sources External RESET pin Watchdog LVD LV DRF 0 0 1 WDG RF 0 1 X
Application notes The LVDRF flag is not cleared when another RESET type occurs (external or watchdog), the LVDRF flag remains set to keep trace of the original failure. In this case, a watchdog reset can be detected by software while an external reset can not. CAUTION: When the LVD is not activated with the associated option byte, the WDGRF flag can not be used in the application.
35/197
ST72325xx
7 INTERRUPTS
7.1 INTRODUCTION The ST7 enhanced interrupt management provides the following features: Hardware interrupts Software interrupt (TRAP) Nested or concurrent interrupt management with flexible interrupt priority and level management: Up to 4 software programmable nesting levels Up to 16 interrupt vectors fixed by hardware 2 non maskable events: RESET, TRAP 1 maskable Top Level event: TLI This interrupt management is based on: Bit 5 and bit 3 of the CPU CC register (I1:0), Interrupt software priority registers (ISPRx), Fixed interrupt vector addresses located at the high addresses of the memory map (FFE0h to FFFFh) sorted by hardware priority order. This enhanced interrupt controller guarantees full upward compatibility with the standard (not nested) ST7 interrupt controller. 7.2 MASKING AND PROCESSING FLOW The interrupt masking is managed by the I1 and I0 bits of the CC register and the ISPRx registers which give the interrupt software priority level of Figure 21. Interrupt Processing Flowchart
RESET PENDING INTERRUPT N Y TRAP Interrupt has the same or a lower software priority than current one N I1:0 Interrupt has a higher software priority than current one Y
each interrupt vector (see Table 7). The processing flow is shown in Figure 21 When an interrupt request has to be serviced: Normal processing is suspended at the end of the current instruction execution. The PC, X, A and CC registers are saved onto the stack. I1 and I0 bits of CC register are set according to the corresponding values in the ISPRx registers of the serviced interrupt vector. The PC is then loaded with the interrupt vector of the interrupt to service and the first instruction of the interrupt service routine is fetched (refer to "Interrupt Mapping" table for vector addresses). The interrupt service routine should end with the IRET instruction which causes the contents of the saved registers to be recovered from the stack. Note: As a consequence of the IRET instruction, the I1 and I0 bits will be restored from the stack and the program in the previous level will resume. Table 7. Interrupt Software Priority Levels
Interrupt software priority Level 0 (main) Level 1 Level 2 Level 3 (= interrupt disable) Level Low I1 1 0 0 1 I0 0 1 0 1
High
FETCH NEXT INSTRUCTION
THE INTERRUPT STAYS PENDING
Y
"IRET" N
RESTORE PC, X, A, CC FROM STACK
EXECUTE INSTRUCTION
STACK PC, X, A, CC LOAD I1:0 FROM INTERRUPT SW REG. LOAD PC FROM INTERRUPT VECTOR
36/197
ST72325xx
INTERRUPTS (Cont'd) Servicing Pending Interrupts As several interrupts can be pending at the same time, the interrupt to be taken into account is determined by the following two-step process: the highest software priority interrupt is serviced, if several interrupts have the same software priority then the interrupt with the highest hardware priority is serviced first. Figure 22 describes this decision process. Figure 22. Priority Decision Process
PENDING INTERRUPTS
TRAP (Non Maskable Software Interrupt) This software interrupt is serviced when the TRAP instruction is executed. It will be serviced according to the flowchart in Figure 21. Caution: TRAP can be interrupted by a TLI. RESET The RESET source has the highest priority in the ST7. This means that the first current routine has the highest software priority (level 3) and the highest hardware priority. See the RESET chapter for more details.
Same
SOFTWARE PRIORITY
Different
HIGHEST SOFTWARE PRIORITY SERVICED HIGHEST HARDWARE PRIORITY SERVICED
When an interrupt request is not serviced immediately, it is latched and then processed when its software priority combined with the hardware priority becomes the highest one. Note 1: The hardware priority is exclusive while the software one is not. This allows the previous process to succeed with only one interrupt. Note 2: TLI,RESET and TRAP can be considered as having the highest software priority in the decision process. Different Interrupt Vector Sources Two interrupt source types are managed by the ST7 interrupt controller: the non-maskable type (RESET, TRAP) and the maskable type (external or from internal peripherals). Non-Maskable Sources These sources are processed regardless of the state of the I1 and I0 bits of the CC register (see Figure 21). After stacking the PC, X, A and CC registers (except for RESET), the corresponding vector is loaded in the PC register and the I1 and I0 bits of the CC are set to disable interrupts (level 3). These sources allow the processor to exit HALT mode.
Maskable Sources Maskable interrupt vector sources can be serviced if the corresponding interrupt is enabled and if its own interrupt software priority (in ISPRx registers) is higher than the one currently being serviced (I1 and I0 in CC register). If any of these two conditions is false, the interrupt is latched and thus remains pending. TLI (Top Level Hardware Interrupt) This hardware interrupt occurs when a specific edge is detected on the dedicated TLI pin. It will be serviced according to the flowchart in Figure 21 as a trap. Caution: A TRAP instruction must not be used in a TLI service routine. External Interrupts External interrupts allow the processor to exit from HALT low power mode. External interrupt sensitivity is software selectable through the External Interrupt Control register (EICR). External interrupt triggered on edge will be latched and the interrupt request automatically cleared upon entering the interrupt service routine. If several input pins of a group connected to the same interrupt line are selected simultaneously, these will be logically ORed. Peripheral Interrupts Usually the peripheral interrupts cause the MCU to exit from HALT mode except those mentioned in the "Interrupt Mapping" table. A peripheral interrupt occurs when a specific flag is set in the peripheral status registers and if the corresponding enable bit is set in the peripheral control register. The general sequence for clearing an interrupt is based on an access to the status register followed by a read or write to an associated register. Note: The clearing sequence resets the internal latch. A pending interrupt (i.e. waiting for being serviced) will therefore be lost if the clear sequence is executed.
37/197
ST72325xx
INTERRUPTS (Cont'd) 7.3 INTERRUPTS AND LOW POWER MODES All interrupts allow the processor to exit the WAIT low power mode. On the contrary, only external and other specified interrupts allow the processor to exit from the HALT modes (see column "Exit from HALT" in "Interrupt Mapping" table). When several pending interrupts are present while exiting HALT mode, the first one serviced can only be an interrupt with exit from HALT mode capability and it is selected through the same decision process shown in Figure 22. Note: If an interrupt, that is not able to Exit from HALT mode, is pending with the highest priority when exiting HALT mode, this interrupt is serviced after the first one serviced. Figure 23. Concurrent Interrupt Management
TRAP SOFTW ARE PRIORITY LEVEL IT2 IT1 IT4 IT3 IT0 I1 I0
7.4 CONCURRENT & NESTED MANAGEMENT The following Figure 23 and Figure 24 show two different interrupt management modes. The first is called concurrent mode and does not allow an interrupt to be interrupted, unlike the nested mode in Figure 24. The interrupt hardware priority is given in this order from the lowest to the highest: MAIN, IT4, IT3, IT2, IT1, IT0, TLI. The software priority is given for each interrupt. Warning: A stack overflow may occur without notifying the software of the failure.
HARDWARE PRIORITY
TRAP IT0 IT1 IT2 IT3 RIM IT4 MAIN MAIN IT1
3 3 3 3 3 3 3/0 10
11 11 11 11 11 11
11 / 10 Figure 24. Nested Interrupt Management
TRAP
SOFTW ARE PRIORITY LEVEL
IT0
IT2
IT1
IT4
IT3
I1
I0
HARDWARE PRIORITY
TRAP IT0 IT1 IT2 IT3 RIM IT4 MAIN IT4 MAIN IT1 IT2
3 3 2 1 3 3 3/0 10
11 11 00 01 11 11
11 / 10
38/197
USED STACK = 20 BY TES
USED STACK = 10 BYTES
ST72325xx
INTERRUPTS (Cont'd) 7.5 INTERRUPT REGISTER DESCRIPTION CPU CC REGISTER INTERRUPT BITS Read / Write Reset Value: 111x 1010 (xAh)
7 1 1 I1 H I0 N Z 0 C ISPR1 I1_7 I0_7 I1_6 I0_6 I1_5 I0_5 I0_9 I1_4 I1_8 I0_4 I0_8
INTERRUPT SOFTWARE PRIORITY REGISTERS (ISPRX) Read/Write (bit 7:4 of ISPR3 are read only) Reset Value: 1111 1111 (FFh)
7 ISPR0 I1_3 I0_3 I1_2 I0_2 I1_1 I0_1 I1_0 0 I0_0
Bit 5, 3 = I1, I0 Software Interrupt Priority These two bits indicate the current interrupt software priority.
Interrupt Software Priority Level 0 (main) Level 1 Level 2 Level 3 (= interrupt disable*) Level Low I1 1 0 0 1 I0 0 1 0 1
ISPR2 ISPR3
I1_11 I0_11 I1_10 I0_10 I1_9 1 1 1 1
I1_13 I0_13 I1_12 I0_12
High
These two bits are set/cleared by hardware when entering in interrupt. The loaded value is given by the corresponding bits in the interrupt software priority registers (ISPRx). They can be also set/cleared by software with the RIM, SIM, HALT, WFI, IRET and PUSH/POP instructions (see "Interrupt Dedicated Instruction Set" table). *Note: TRAP and RESET events can interrupt a level 3 program.
These four registers contain the interrupt software priority of each interrupt vector. Each interrupt vector (except RESET and TRAP) has corresponding bits in these registers where its own software priority is stored. This correspondance is shown in the following table.
Vector address FFFBh-FFFAh FFF9h-FFF8h ... FFE1h-FFE0h ISPRx bits I1_0 and I0_0 bits* I1_1 and I0_1 bits ... I1_13 and I0_13 bits
Each I1_x and I0_x bit value in the ISPRx registers has the same meaning as the I1 and I0 bits in the CC register. Level 0 can not be written (I1_x=1, I0_x=0). In this case, the previously stored value is kept. (example: previous=CFh, write=64h, result=44h) The TLI, RESET, and TRAP vectors have no software priorities. When one is serviced, the I1 and I0 bits of the CC register are both set. *Note: Bits in the ISPRx registers which correspond to the TLI can be read and written but they are not significant in the interrupt process management. Caution: If the I1_x and I0_x bits are modified while the interrupt x is executed the following behaviour has to be considered: If the interrupt x is still pending (new interrupt or flag not cleared) and the new software priority is higher than the previous one, the interrupt x is re-entered. Otherwise, the software priority stays unchanged up to the next interrupt request (after the IRET of the interrupt x).
39/197
ST72325xx
INTERRUPTS (Cont'd)
Table 8. Dedicated Interrupt Instruction Set
Instruction HALT IR ET JRM JRNM POP CC RIM SIM TRAP WFI New Description Entering Halt mode Interrupt routine return Jump if I1:0=11 (level 3) Jump if I1:0<>11 Pop CC from the Stack Enable interrupt (level 0 set) Disable interrupt (level 3 set) Software trap Wait for interrupt Pop CC, A, X, PC I1:0=11 ? I1:0<>11 ? Mem => CC Load 10 in I1:0 of CC Load 11 in I1:0 of CC Software NMI I1 1 1 1 1 H I0 0 1 1 0 N Z C Function/Example I1 1 I1 H H I0 0 I0 N Z C N Z C
Note: During the execution of an interrupt routine, the HALT, POPCC, RIM, SIM and WFI instructions change the current software priority up to the next IRET instruction or one of the previously mentioned instructions.
40/197
ST72325xx
INTERRUPTS (Cont'd) Table 9. Interrupt Mapping
Exit from Priority HALT/ Order ACTIVE HALT yes no yes Higher Priority yes yes yes yes yes SPICS R T A SR T B SR SCISR SICSR (see periph) AR TCSR Lower Priority y es1 no no no no no yes2
N
Source Block
Description
Register Label
Address Vector
RES ET TRAP 0 1 2 3 4 5 6 7 8 9 10 11 12 13 S PI TIMER A TIMER B S CI AVD I2C PWM ART T LI MCC/RTC/ CSS e i0 e i1 e i2 e i3
Reset Software interrupt External top level interrupt Main clock controller time base interrupt Safe oscillator activation interrupt External interrupt port A3..0 External interrupt port F2..0 External interrupt port B3..0 External interrupt port B7..4 Not used SPI peripheral interrupts TIMER A peripheral interrupts TIMER B peripheral interrupts SCI Peripheral interrupts Auxiliary Voltage detector interrupt I2C Peripheral interrupts PWM ART interrupt
N/A EICR M CCSRSICSR
FFFEh-FFFFh FFFCh-FFFDh FFFAh-FFFBh FFF8h-FFF9h FFF6h-FFF7h FFF4h-FFF5h FFF2h-FFF3h FFF0h-FFF1h FFEEh-FFEFh FFECh-FFEDh FFEAh-FFEBh FFE8h-FFE9h FFE6h-FFE7h FFE4h-FFE5h FFE2h-FFE3h FFE0h-FFE1h
N/A
Notes: 1. Exit from HALT possible when SPI is in slave mode. 2. Exit from HALT possible when PWM ART is in external clock mode.
7.6 EXTERNAL INTERRUPTS 7.6.1 I/O Port Interrupt Sensitivity The external interrupt sensitivity is controlled by the IPA, IPB and ISxx bits of the EICR register (Figure 25). This control allows to have up to 4 fully independent external interrupt source sensitivities. Each external interrupt source can be generated on four (or five) different events on the pin: Falling edge Rising edge Falling and rising edge
Falling edge and low level Rising edge and high level (only for ei0 and ei2) To guarantee correct functionality, the sensitivity bits in the EICR register can be modified only when the I1 and I0 bits of the CC register are both set to 1 (level 3). This means that interrupts must be disabled before changing sensitivity. The pending interrupts are cleared by writing a different value in the ISx[1:0], IPA or IPB bits of the EICR.
41/197
ST72325xx
INTERRUPTS (Cont'd) Figure 25. External Interrupt Control bits
PORT A3 INTERRUPT PAOR.3 PADDR.3 PA3
EICR IS20 IS21 ei0 INTERRUPT SOURCE
SENSITIVITY CONTROL
IPA BIT PORT F [2:0] INTERRUPTS PFOR.2 PFDDR.2 PF2 EICR IS20 IS21 PF2 PF1 PF0
SENSITIVITY CONTROL
ei1 INTERRUPT SOURCE
PORT B [3:0] INTERRUPTS PBOR.3 PBDDR.3 PB3
EICR IS10 IS11 PB3 PB2 PB1 PB0
SENSITIVITY CONTROL
ei2 INTERRUPT SOURCE
IPB BIT
PORT B4 INTERRUPT PBOR.4 PBDDR.4 PB4
EICR IS10 IS11 ei3 INTERRUPT SOURCE
SENSITIVITY CONTROL
42/197
ST72325xx
7.7 EXTERNAL INTERRUPT CONTROL REGISTER (EICR) Read / Write Reset Value: 0000 0000 (00h)
7 IS11 IS10 IPB I S21 I S20 IPA TLIS 0 TLIE
- ei0 (port A3)
External Interrupt Sensitivity IS21 IS20 IPA bit =0 0 0 0 1 0 1 Falling edge & low level Rising edge only Falling edge only IPA bit =1 Rising edge & high level Falling edge only Rising edge only
Bit 7:6 = IS1[1:0] ei2 and ei3 sensitivity The interrupt sensitivity, defined using the IS1[1:0] bits, is applied to the following external interrupts: - ei2 (port B3..0)
External Interrupt Sensitivity IS11 IS10 IPB bit =0 0 0 1 1 0 1 0 1 Falling edge & low level Rising edge only Falling edge only IPB bit =1 Rising edge & high level Falling edge only Rising edge only
1 1
Rising and falling edge
- ei1 (port F2..0)
I S 21 IS20 0 0 1 1 0 1 0 1 External Interrupt Sensitivity Falling edge & low level Rising edge only Falling edge only Rising and falling edge
Rising and falling edge
- ei3 (port B4)
IS11 IS10 0 0 1 1 0 1 0 1 External Interrupt Sensitivity Falling edge & low level Rising edge only Falling edge only Rising and falling edge
These 2 bits can be written only when I1 and I0 of the CC register are both set to 1 (level 3). Bit 2 = IPA Interrupt polarity for port A This bit is used to invert the sensitivity of the port A [3:0] external interrupts. It can be set and cleared by software only when I1 and I0 of the CC register are both set to 1 (level 3). 0: No sensitivity inversion 1: Sensitivity inversion Bit 1 = TLIS TLI sensitivity This bit allows to toggle the TLI edge sensitivity. It can be set and cleared by software only when TLIE bit is cleared. 0: Falling edge 1: Rising edge Bit 0 = TLIE TLI enable This bit allows to enable or disable the TLI capability on the dedicated pin. It is set and cleared by software. 0: TLI disabled 1: TLI enabled Note: a parasitic interrupt can be generated when clearing the TLIE bit.
These 2 bits can be written only when I1 and I0 of the CC register are both set to 1 (level 3). Bit 5 = IPB Interrupt polarity for port B This bit is used to invert the sensitivity of the port B [3:0] extern |
