スマート･プラグ

Key Features

• EMC: burst - IEC 61000-4-4 - 8 kV
• EMC: surge - IEC 61000-4-5 - 2 kV
• RoHS compliant
• Isolation: non isolated - N connected to output GND
• PCB type and size:FR4, single side 70 μmdim.: 27 x 45 mm
• Input voltage Vin: 85 - 500 VAC (f: 45 - 66 Hz)
• Output current: 150 mA total (5 V and 12 V output) output current for full input voltage range
• Output voltages:V1= 12 V ± 10%V2= 5 V ± 4%
• Short-circuit protection
• EMI: In accordance with EN55022 - class B
• Standby: 96 mW at 230 VAC

さらに表示

Key Features

• Universal input mains range:
  • input voltage 90 - 264 V_AC
  • frequency 45 - 65 Hz
• Single-output voltage: 12 V at 1 A continuous operation
• Standby mains consumption: < 30 mW at 230 V_AC
• Average efficiency: > 80%
• Fully protected against faults (overload, feedback disconnection and overheating)
• EMI: according to EN55022-Class-B
• RoHS compliant

さらに表示

Key Features

• 0.2% accuracy single-phase meter
• V_nom (RMS) = 140 to 300 V, I_nom /I_max(RMS) = 5/100 A, f_lin = 50/60 Hz ± 10%
• Connector for USB isolated hardware programmer tool STEVAL-IPE023V1 and PC GUI
• RS232 and UART isolated connectors to PC GUI
• SPI/UART switch for device peripheral selection
• 2 programmable LEDs on board
• Digital expansion to external system-on-chip or MCU
• 3.3 V power supply: external or through STEVAL-IPE023V1 isolated USB board
• IEC61000 standard compliant
• RoHS compliant

さらに表示

Key Features

• Common features
  • STM32 microcontroller in LQFP144 package
  • 3 user LEDs
  • 2 user and reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:SWDST Zio expansion connector including ARDUINO^® Uno V3ST morpho expansion connector
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External or internal SMPS to generate V_core logic supply
  • Ethernet compliant with IEEE-802.3-2002
  • USB OTG full speed or device only
  • Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45
  • Arm^® Mbed Enabled™ compliant

さらに表示

Key Features

• Common features
  • STM32 microcontroller in LQFP144 package
  • 3 user LEDs
  • 2 user and reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:SWDST Zio expansion connector including ARDUINO^® Uno V3ST morpho expansion connector
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External or internal SMPS to generate V_core logic supply
  • Ethernet compliant with IEEE-802.3-2002
  • USB OTG full speed or device only
  • Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45
  • Arm^® Mbed Enabled™ compliant

さらに表示

Key Features

• Universal AC main input voltage range: 85V_AC to 265V_AC
• Output range: 5 V / 0.85 A
• Rated output power: 4.25 W
• Input power in standby @ 230 V_AC : < 9 mW
• Active mode efficiency: > 74%
• EMI: according to EN55022-Class-B
• RoHS compliant

さらに表示

Key Features

• AC input voltage range: 90 V to 300 V
• LED voltage / current: 60 V-105 V / 700 mA
• Constant LED current: 700 mA ± 2%
• Power factor: > 0.95
• Input current THD: < 10%
• Standby consumption: < 0.5 W
• Open-circuit and short-circuit protection
• Provision for smart features: ON / OFF / DIMMING
• RoHS compliant

さらに表示

Key Features

• Input voltage: V_IN = 90 - 305 V_rms , f: 45 - 66 Hz
• Output current: 700 mA (V_LED = 24 V to 48 V)
• Dimming: 100% to 10%
• Dimming interfaces: 0 - 10 V and PWM input
• High power factor, low THD
• Efficiency: > 90% @ full load
• Open load voltage limiting (52.4 V)
• Optional remote turn-off input
• Optional 3.3 V – 0.1 A voltage regulator
• Fast V_OUT discharge
• RoHS compliant

さらに表示

Key Features

• Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
• Up to 4-Kbit memory with NDEF support
• 54 mm diameter, single layer circular antenna
• Compatible with STM32 Nucleo boards
• Equipped with Arduino™ UNO R3 connector
• Self-powered or powered through the Arduino™ UNO R3 connectors
• Three general purpose LEDs
• Scalable solution, capable of cascading multiple boards for larger systems
• Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
• FCC and IC verified
• RoHS compliant

さらに表示

Key Features

• Two ready-to-use printed circuit boards (PCB):
  • ST25DV_Discovery_Mboard:
  • STM32F405VGT6 LQFP100 32-bit microcontroller, with 1 Mbyte Flash memory, 192 + 4 Kbytes SRAM.
  • LCD color screen (320 x 200 pixels)
  • Touch screen driver
  • Different color LEDs (power, user, ST link)
  • User push button
  • Joystick for menu selection
  • リセットボタン
  • On board ST link for microcontroller firmware upgrade and debug
  • ST link mini USB
  • User micro USB
  • USB micro or mini connector for board powering
  • Demonstration use cases stored in memory
  • Demonstration edition (optional add-on module) with Bluetooth Low Energy module, Wi-Fi^® module and JTAG 20 pin connector
• ST25DV_Discovery_ANT_C5:
  • 40 mm x 24 mm, 13.56 MHz inductive antenna etched on the PCB
  • ST25DV04K Dynamic NFC / RFID tag
  • I² C interface connector
  • Energy harvesting output (VOUT) with a 10 nF capacitance filtering circuit
  • GPO configurable as RF WIP/BUSY output, to indicate that an RF operation is ongoing

さらに表示

Key Features

• S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
• STM32 Nucleo-64 development board with STM32L152RE MCU
• Suitable for wireless M-Bus systems
• Suitable for SigFox applications
• Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
• Programmable RF output power up to +27 dBm
• Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
• Air data rate from 0.3 to 500 kbps
• Excellent performance of receiver sensitivity (up to -130 dBm)
• Low duty cycle RX/TX operation mode
• Automatic acknowledgement, retransmission and timeout protocol engine
• SPI interface for microcontroller
• USB interface
• RoHS compliant

さらに表示

Key Features

• STM32 Nucleo expansion board based on the ST7580 power line networking system-on-chip
• ST7580 main characteristics:
  • FSK, PSK modem for robust wireline communication up to 28.8 kbps
  • 8-18 V analog supply voltage
  • 3.3 V digital supply
  • Output transmitted signal capability up to 14 V_p-p , 1 A_rms
  • Frequency range 9-250 kHz
• TX and RX filters on board optimized for the CENELEC B (95-125 kHz) frequency band, suitable for IoT / Smart Home / Smart City applications
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connectors
• Example firmware available for point-to-point communication, compatible with STM32Cube firmware
• RoHS compliant

さらに表示

Key Features

• Bluetooth^® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
• Associated BlueNRG-2 development kit SW package including firmware and documentation
• Up to +8 dBm available output power (at antenna connector)
• Excellent receiver sensitivity (-88 dBm)
• Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
• Bluetooth^® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
• New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
• SMA connector for antenna or measuring equipment
• 3 user LEDs
• 2 user buttons
• 3D digital accelerometer and 3D digital gyroscope
• MEMS pressure sensor with embedded temperature sensor
• RoHS compliant

さらに表示

Key Features

• Power line communication evaluation kit based on ST8500 and STLD1 devices
• Complete power line communication (PLC) reference design, suitable to evaluate several narrow-band PLC protocols (G3, PRIME, etc.) in the frequency range up to 500 kHz
• Modular board architecture
  • ST8500 full performance PLC module including the companion STLD1 line driver
  • STM32 microcontroller mother board for system management, application host controller and interface to PC
  • STEVAL-ISA175V1, wide-range input voltage, 9.4 W power supply board based on VIPER26HD
• Optional 12 - 15 V DC input available for laboratory tests without AC mains connection

さらに表示

Key Features

• ST25DV64K dynamic NFC tag solution based on 64K-bit (8K-Byte) EEPROM and with I²C interface, Fast Transfer Mode and Energy Harvesting features
• STM32L031K6 ultra-low-power ARM Cortex-M0+ MCU running at 32 MHz with 32-Kbytes Flash and 8-Kbytes RAM
• LIS2DW12 ultra-low-power high-performance three-axis linear accelerometer
• LPS22HB ultra-compact piezo-resistive absolute pressure sensor which functions as a digital output barometer: 260-1260 hPa
• HTS221 capacitive digital sensor for relative humidity and temperature
• STLQ015 low drop linear regulator power management
• CR2032 Battery powered (not included)
• STM32Cube function pack (FP-SNS-SMARTAG1)
• Android (Google Play) and iOS demo apps (ST SmarTag)
• Suitable for the following applications:
  • Internet of Things
  • Supply Chain and Cold-Chain Management
  • Smart building, home and city
  • Retail and apparel
  • Smart packaging
  • Medical and pharmaceutical
  • Batteryless sensing
  • Smart agriculture (soil control, animal tracking, etc.)

さらに表示

Key Features

• S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
• STM32 Nucleo-64 development board with STM32L0 MCU
• Suitable for Wireless M-Bus systems
• Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
• Programmable RF output power up to +16 dBm
• Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
• Air data rate from 0.3 to 500 kbps
• Ultra-low power consumption:
  • 6.7 mA RX
  • 10 mA TX @ +10 dBm
• Excellent performance of receiver sensitivity (up to -130 dBm)
• Low duty cycle RX/TX operation mode
• Automatic acknowledgement, retransmission, and timeout protocol engine
• SPI interface for microcontroller
• USB interface
• RoHS compliant

さらに表示

Key Features

• Suitable for point-to-multipoint 2-way power line communication (PLC) over AC mains
• Flexible 2-board architecture:
  • EVALST7580-1, PLC board based on the ST7580 narrow-band FSK/PSK power line networking system-on-chip
  • EVLALTAIR900-M1, wide-range input voltage, 7.5 W power supply board based on the ALTAIR04-900 quasi-resonant current-mode SMPS controller
• STM32 microcontroller hosted on the EVALST7580-1 board to handle the ST7580 device and build a standalone power line node
• External access through several interface types: USB, SPI, I² C, USART, JTAG
• Opportunity to save and load data to/from an external μ-SD card
• Intuitive graphical user interface (GUI) for the Windows^® environment with fully programmable transceiver parameters
• Suitable for CENELEC EN50065 and FCC part 15 compliant applications

さらに表示