概要
ソリューション
HW Evaluation Tools
リソース
ツール & ソフトウェア
Key Products
Get Started

街路照明設備は、大量のエネルギーを消費する初歩的な照明から、各種サービスの中心的存在へと進化を遂げています。プレゼンス/交通レベル・モニタリングや事故検出監視のほか、各道路状況や気象条件に合わせて照明レベルを最適化することにより、都市をSmart Cityへと導く行政の取り組みを後押ししていることもその一例です。

STは、幅広い有線/無線通信ソリューション、パワー・マネージメントおよび電源ソリューション、LED駆動ソリューションや、低消費電力の高性能マイクロコントローラSTM32、プレゼンス/近接/カメラ/環境センサ、およびMEMSマイクの提供により、先進的な街路照明システムの設計をサポートしています。

 

推奨製品

製品型番
Description
STEVAL-ISA084V1 4 A peak, 800 kHz fixed-frequency PWM synchronous step-down demonstration board with enable on/off based on the ST1S40 Quick view

主な特徴

  • Vin : 4 V to 18 V
  • Vout: 3.3 V
  • Maximum output current: 4 A
  • Switching frequency: 800 kHz
  • Short-circuit: protected
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA158V1 38 V - 2 A synchronous step-down switching regulator evaluation board based on the A6986 Quick view

主な特徴

  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • 30 µA IQ at light load (LCM VOUT = 3.3 V)
  • 5 µA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-VP013B1B 5 V / 100 mA high voltage optimized buck-converter based on VIPer013BLS Quick view

主な特徴

  • Buck topology
  • Input power consumption:
    • 20 mW at 230 VAC in no load condition
    • 400 mW at 230 VAC in 250 mW load
  • Input voltage: 60 to 300 VAC
  • Output voltage: 5 V
  • Output current: 100 mA
  • Switching frequency: 60 kHz with jittering
  • Max ambient. temperature: 60 °C
  • Automatic restart protections: OLP, short-circuit, VCC clamp, max duty cycle counter, thermal shutdown
  • Pulse-skip protection to prevent flux-runaway
  • Dimensions: 27 mm x 24 mm
  • Meets IEC55022 Class B conducted EMI even with reduced EMI filter, thanks to the frequency jittering feature
  • VIPer013B 800V avalanche rugged technology and embedded protections ensure enhanced system reliability
  • RoHS compliant

さらに表示

画像

Image
Image
EVALSTDRIVE601 EVALSTRIVE601 Quick view

主な特徴

  • High voltage rail up to 600V
  • Driver supply input voltage range 9V-20V
  • STGD6M65DF2 IGBTs power stage featuring:
    • V(BR)CES = 650 V
    • VCE(sat) = 1.55 V @ IC = 6 A
  • Dual footprint for IGBT/MOSFET package:
    • DPAK
    • PowerFlat 8x8
  • Selectable single or 3-shunt current sensing topology:
    • Sensored or sensorless BEMF detection
    • FOC or 6-Step algorithm
  • SmartShutdown overcurrent protection
  • Hall effect sensors connector
  • Bus voltage sensing
  • 450V bulk capacitor
  • Connector for interfacing with MCU
  • RoHS compliant

さらに表示

STEVAL-ILL053V2 48 V - 130 W high efficiency converter with PFC for LED street lighting applications based on L6562 and L6599 Quick view

主な特徴

  • Extended input mains range: 85 to 305 VAC - frequency 45 to 55 Hz
  • Output voltage: 48 V at 2.7 A
  • Long-life: electrolytic capacitors not used
  • Mains harmonics in accordance with EN61000-3-2 Class C
  • Efficiency at full load greater than 91% at 115 VAC
  • EMI in accordance with EN55022 Class B; EN55015
  • Safety: double insulation, in accordance with EN60950, SELV
  • Dimensions: 75 x 135 mm, 30 mm maximum component height
  • PCB: single side, 35 μm, FR-4, mixed PTH/SMT
  • RoHS compliant
  • WEEE compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-LLL004V1 75 W wide input voltage digitally controlled constant current LED driver Quick view

主な特徴

  • Wide input voltage range 85 – 265 VAC
  • Transition Mode PFC
  • Two constant current outputs working in transition mode based on different topologies:
    • Buck topology
    • Inverse buck topology
  • Output current: 500 mA ±2.5%
    • Number of LEDs connected at output: 16 – 24 white LEDs (3.3 V each)
  • PFC > 0.97 and THD < 20% at full load with input voltage 85-265 VAC
  • Peak Efficiency at maximum load ≅ 90%
  • Comprehensive safety protections:
    • Open/no-load circuit protection
    • Short-/overload circuit protection
  • Soft start implementation
  • LED dimming range: 0.5% to 100%
    • Analog dimming
    • Digital dimming
  • Dimming control options:
    • Push button
    • 0-10 V input
  • Meet IEC55022 Class B
  • WEEE and RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ILL066V2 100 W LED street lighting evaluation board using the STLUX385A digital controller Quick view

主な特徴

  • based on STLUX385A digital controller
  • high efficiency (92%)
  • primary side controlled
  • up to 100 W (100 V at 1 A or 200 V at 0.5 A)
  • single isolated output suitable for LED connection
  • wide input voltage range: 90 V to 265 V AC
  • adjustable LED current and dimming
  • output resolution: 11-bit equivalent
  • IDLE mode power consumption: < 250 mW
  • real-time fault detection and protection (short-circuit or open circuit)
  • remote control via:
    • DALI ed.2.0
    • 0 - 10 V
    • UART
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ILL070V4 35 W dimmable single string LED driver using HVLED001A and STF10LN80K5 Quick view

主な特徴

  • Input voltage: VIN = 90 - 305 Vrms , f: 45 - 66 Hz
  • Output current: 700 mA (VLED = 24 V to 48 V)
  • Dimming: 100% to 10%
  • Dimming interfaces: 0 - 10 V and PWM input
  • High power factor, low THD
  • Efficiency: > 90% @ full load
  • Open load voltage limiting (52.4 V)
  • Optional remote turn-off input
  • Optional 3.3 V – 0.1 A voltage regulator
  • Fast VOUT discharge
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics Gerber
STEVAL-ILL074V2 60 W wide input range flyback converter using HVLED001A controller in FOT mode Quick view

主な特徴

  • Input voltage: Vin = 90 - 277 Vrms , f = 45-66 Hz
  • Output voltage: 52 V / 1.2 A
  • High power factor, low THD
  • Full load efficiency: above 90%
  • Short circuit protection
  • Safety: compliant with EN60065
  • PCB board: 165 mm x 50 mm double-sided PCB
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ILL013V1 80 W offline PFC and LED driver demonstration board with dimming based on the L6562A Quick view

主な特徴

  • EN55015 and EN61000-3-2 compliant
  • EMI filter implemented
  • Non-isolated SMPS
  • Universal PWM input for dimming (external board required)
  • 80 W LED driver
  • High efficiency (~90%)
  • 350 mA, 700 mA and 1 A LED current settings
  • High power factor: 0.982 for 230 V/50 Hz AC
  • Brightness regulation between 0 and 100%
  • Wide input voltage range: 88 V to 265 VAC

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ILL043V1 High end, 75 W high power factor flyback LED driver based on the L6562A with two dimmable strings Quick view

主な特徴

  • Mains voltage range VACmin = 165Vac , VACmax = 277 Vac
  • Minimum mains frequency fl = 47 Hz
  • DC output voltage Vout = 65 V
  • Maximum output current Iout = 1.5 A
  • Maximum 2fL output ripple ΔVO% = 1.0%
  • Minimum switching frequency fswmin = 40 KHz
  • Expected efficiency: 90%
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA152V1 3.3 V/3 A high efficiency step down DC-DC converter (VIN= 4.5 to 60 V) based on the L7987 Quick view

主な特徴

  • 3.3 V output voltage
  • 3 A DC output current
  • 4.5 V to 60 V input voltage
  • 500 kHz switching frequency
  • 3.5 ms programmed soft-start
  • VBIAS switch-over for improved efficiency at light load
  • 180° out of phase synchronization available
  • Open drain PGOOD available
  • Auto recovery overcurrent and thermal protection
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
32F3348DISCOVERY Discovery kit with STM32F334C8 MCU Quick view

主な特徴

  • STM32F334C8T6 microcontroller featuring 64 KB of Flash memory, 16 KB RAM in an LQFP48 package.
  • On-board ST-LINK/V2-1 with selection mode switch to use the kit as a standalone ST-LINK/V2-1 (with SWD connector for programming and debugging).
  • mbed -enabled (mbed.org)
  • USB ST-LINK with re-enumeration capability and three different interfaces:
    • virtual com port
    • mass storage
    • debug port
  • Board power supply: through USB bus or from an external 5 V supply voltage.
  • External application power supply: 3 V and 5 V.
  • High brightness LED dimming with buck converter.
  • One buck / boost converter.
  • Six LEDs:
    • LD1 (red) for 3.3 V power on
    • LD2 (red/green) for USB communication
    • Four user LEDs: LD3 (red), LD4 (orange), LD5 (green) and LD6 (blue).
  • Two pushbuttons (user and reset).
  • Extension header for LQFP48 I/Os for a quick connection to the prototyping board and easy probing.
  • Comprehensive free software including a variety of examples, part of STM32CubeF3 package or STSW-STM32148 for legacy Standard Library usage.

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA095V1 Up to 3 A step-down switching regulator based on the ST1S14 Quick view

主な特徴

  • 3 A DC output current
  • Operating input voltage from 5.5 V to 48 V
  • 850 kHz internally fixed switching frequency
  • Internal soft-start
  • Internal current limiting
  • Inhibit for zero current consumption
  • 2 mA maximum quiescent current over-temperature range
  • Thermal shutdown
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
製品型番
STEVAL-ISA084V1

4 A peak, 800 kHz fixed-frequency PWM synchronous step-down demonstration board with enable on/off based on the ST1S40

主な特徴

  • Vin : 4 V to 18 V
  • Vout: 3.3 V
  • Maximum output current: 4 A
  • Switching frequency: 800 kHz
  • Short-circuit: protected
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA158V1

38 V - 2 A synchronous step-down switching regulator evaluation board based on the A6986

主な特徴

  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • 30 µA IQ at light load (LCM VOUT = 3.3 V)
  • 5 µA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-VP013B1B

5 V / 100 mA high voltage optimized buck-converter based on VIPer013BLS

主な特徴

  • Buck topology
  • Input power consumption:
    • 20 mW at 230 VAC in no load condition
    • 400 mW at 230 VAC in 250 mW load
  • Input voltage: 60 to 300 VAC
  • Output voltage: 5 V
  • Output current: 100 mA
  • Switching frequency: 60 kHz with jittering
  • Max ambient. temperature: 60 °C
  • Automatic restart protections: OLP, short-circuit, VCC clamp, max duty cycle counter, thermal shutdown
  • Pulse-skip protection to prevent flux-runaway
  • Dimensions: 27 mm x 24 mm
  • Meets IEC55022 Class B conducted EMI even with reduced EMI filter, thanks to the frequency jittering feature
  • VIPer013B 800V avalanche rugged technology and embedded protections ensure enhanced system reliability
  • RoHS compliant

さらに表示

画像

Image
Image

主な特徴

  • High voltage rail up to 600V
  • Driver supply input voltage range 9V-20V
  • STGD6M65DF2 IGBTs power stage featuring:
    • V(BR)CES = 650 V
    • VCE(sat) = 1.55 V @ IC = 6 A
  • Dual footprint for IGBT/MOSFET package:
    • DPAK
    • PowerFlat 8x8
  • Selectable single or 3-shunt current sensing topology:
    • Sensored or sensorless BEMF detection
    • FOC or 6-Step algorithm
  • SmartShutdown overcurrent protection
  • Hall effect sensors connector
  • Bus voltage sensing
  • 450V bulk capacitor
  • Connector for interfacing with MCU
  • RoHS compliant

さらに表示

STEVAL-ILL053V2

48 V - 130 W high efficiency converter with PFC for LED street lighting applications based on L6562 and L6599

主な特徴

  • Extended input mains range: 85 to 305 VAC - frequency 45 to 55 Hz
  • Output voltage: 48 V at 2.7 A
  • Long-life: electrolytic capacitors not used
  • Mains harmonics in accordance with EN61000-3-2 Class C
  • Efficiency at full load greater than 91% at 115 VAC
  • EMI in accordance with EN55022 Class B; EN55015
  • Safety: double insulation, in accordance with EN60950, SELV
  • Dimensions: 75 x 135 mm, 30 mm maximum component height
  • PCB: single side, 35 μm, FR-4, mixed PTH/SMT
  • RoHS compliant
  • WEEE compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-LLL004V1

75 W wide input voltage digitally controlled constant current LED driver

主な特徴

  • Wide input voltage range 85 – 265 VAC
  • Transition Mode PFC
  • Two constant current outputs working in transition mode based on different topologies:
    • Buck topology
    • Inverse buck topology
  • Output current: 500 mA ±2.5%
    • Number of LEDs connected at output: 16 – 24 white LEDs (3.3 V each)
  • PFC > 0.97 and THD < 20% at full load with input voltage 85-265 VAC
  • Peak Efficiency at maximum load ≅ 90%
  • Comprehensive safety protections:
    • Open/no-load circuit protection
    • Short-/overload circuit protection
  • Soft start implementation
  • LED dimming range: 0.5% to 100%
    • Analog dimming
    • Digital dimming
  • Dimming control options:
    • Push button
    • 0-10 V input
  • Meet IEC55022 Class B
  • WEEE and RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ILL066V2

100 W LED street lighting evaluation board using the STLUX385A digital controller

主な特徴

  • based on STLUX385A digital controller
  • high efficiency (92%)
  • primary side controlled
  • up to 100 W (100 V at 1 A or 200 V at 0.5 A)
  • single isolated output suitable for LED connection
  • wide input voltage range: 90 V to 265 V AC
  • adjustable LED current and dimming
  • output resolution: 11-bit equivalent
  • IDLE mode power consumption: < 250 mW
  • real-time fault detection and protection (short-circuit or open circuit)
  • remote control via:
    • DALI ed.2.0
    • 0 - 10 V
    • UART
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ILL070V4

35 W dimmable single string LED driver using HVLED001A and STF10LN80K5

主な特徴

  • Input voltage: VIN = 90 - 305 Vrms , f: 45 - 66 Hz
  • Output current: 700 mA (VLED = 24 V to 48 V)
  • Dimming: 100% to 10%
  • Dimming interfaces: 0 - 10 V and PWM input
  • High power factor, low THD
  • Efficiency: > 90% @ full load
  • Open load voltage limiting (52.4 V)
  • Optional remote turn-off input
  • Optional 3.3 V – 0.1 A voltage regulator
  • Fast VOUT discharge
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics Gerber
STEVAL-ILL074V2

60 W wide input range flyback converter using HVLED001A controller in FOT mode

主な特徴

  • Input voltage: Vin = 90 - 277 Vrms , f = 45-66 Hz
  • Output voltage: 52 V / 1.2 A
  • High power factor, low THD
  • Full load efficiency: above 90%
  • Short circuit protection
  • Safety: compliant with EN60065
  • PCB board: 165 mm x 50 mm double-sided PCB
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ILL013V1

80 W offline PFC and LED driver demonstration board with dimming based on the L6562A

主な特徴

  • EN55015 and EN61000-3-2 compliant
  • EMI filter implemented
  • Non-isolated SMPS
  • Universal PWM input for dimming (external board required)
  • 80 W LED driver
  • High efficiency (~90%)
  • 350 mA, 700 mA and 1 A LED current settings
  • High power factor: 0.982 for 230 V/50 Hz AC
  • Brightness regulation between 0 and 100%
  • Wide input voltage range: 88 V to 265 VAC

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ILL043V1

High end, 75 W high power factor flyback LED driver based on the L6562A with two dimmable strings

主な特徴

  • Mains voltage range VACmin = 165Vac , VACmax = 277 Vac
  • Minimum mains frequency fl = 47 Hz
  • DC output voltage Vout = 65 V
  • Maximum output current Iout = 1.5 A
  • Maximum 2fL output ripple ΔVO% = 1.0%
  • Minimum switching frequency fswmin = 40 KHz
  • Expected efficiency: 90%
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA152V1

3.3 V/3 A high efficiency step down DC-DC converter (VIN= 4.5 to 60 V) based on the L7987

主な特徴

  • 3.3 V output voltage
  • 3 A DC output current
  • 4.5 V to 60 V input voltage
  • 500 kHz switching frequency
  • 3.5 ms programmed soft-start
  • VBIAS switch-over for improved efficiency at light load
  • 180° out of phase synchronization available
  • Open drain PGOOD available
  • Auto recovery overcurrent and thermal protection
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
32F3348DISCOVERY

Discovery kit with STM32F334C8 MCU

主な特徴

  • STM32F334C8T6 microcontroller featuring 64 KB of Flash memory, 16 KB RAM in an LQFP48 package.
  • On-board ST-LINK/V2-1 with selection mode switch to use the kit as a standalone ST-LINK/V2-1 (with SWD connector for programming and debugging).
  • mbed -enabled (mbed.org)
  • USB ST-LINK with re-enumeration capability and three different interfaces:
    • virtual com port
    • mass storage
    • debug port
  • Board power supply: through USB bus or from an external 5 V supply voltage.
  • External application power supply: 3 V and 5 V.
  • High brightness LED dimming with buck converter.
  • One buck / boost converter.
  • Six LEDs:
    • LD1 (red) for 3.3 V power on
    • LD2 (red/green) for USB communication
    • Four user LEDs: LD3 (red), LD4 (orange), LD5 (green) and LD6 (blue).
  • Two pushbuttons (user and reset).
  • Extension header for LQFP48 I/Os for a quick connection to the prototyping board and easy probing.
  • Comprehensive free software including a variety of examples, part of STM32CubeF3 package or STSW-STM32148 for legacy Standard Library usage.

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA095V1

Up to 3 A step-down switching regulator based on the ST1S14

主な特徴

  • 3 A DC output current
  • Operating input voltage from 5.5 V to 48 V
  • 850 kHz internally fixed switching frequency
  • Internal soft-start
  • Internal current limiting
  • Inhibit for zero current consumption
  • 2 mA maximum quiescent current over-temperature range
  • Thermal shutdown
  • RoHS compliant

さらに表示

画像

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
00 Files selected for download

技術文書

    • Description バージョン サイズ アクション
      AN4461
      100 W LED street lighting application using STLUX385A
      4.0
      1.81 MB
      PDF
      AN5316
      35 W wide input range flyback converter using HVLED001B quasi resonant Flyback controller and STF10LN80K5
      1.0
      2.8 MB
      PDF
      AN3105
      48 V - 130 W high efficiency converter with PFC for LED street lighting applications - European version
      2.0
      3.52 MB
      PDF
      AN3106
      48 V - 130 W high-efficiency converter with PFC for LED street lighting applications
      3.1
      1.17 MB
      PDF
      AN2644
      An introduction to LLC resonant half-bridge converter
      2.0
      1.27 MB
      PDF
      AN4656
      Bootloading procedure for STLUX™ and STNRG™ digital controllers
      2.0
      635.41 KB
      PDF
      AN2983
      Constant current inverse buck LED driver using L6562A
      1.3
      1.9 MB
      PDF
      AN2680
      Fan speed controller based on STDS75 or STLM75 digital temperature sensor and ST72651AR6 MCU
      1.4
      125.82 KB
      PDF
      AN4250
      Fishbone diagram for power factor correction
      1.1
      772.32 KB
      PDF
      AN4539
      HRTIM cookbook
      2.0
      956.82 KB
      PDF
      AN4932
      HVLED001A - enhanced QR high power factor flyback controller for LED drivers
      2.0
      3.01 MB
      PDF
      AN4885
      High brightness LED dimming using the STM32F334 Discovery kit
      1.1
      594.69 KB
      PDF
      AN5119
      How to design an application from draft with STNRG011
      1.0
      343.37 KB
      PDF
      AN2648
      Increasing the resolution of analog temperature sensors
      1.4
      161.7 KB
      PDF
      AN2450
      LLC resonant half-bridge converter design guideline
      6.0
      746.74 KB
      PDF
      AN4406
      MDmesh™ M2: the new ST super-junction technology ideal for resonant topologies
      1.0
      652.78 KB
      PDF
      AN5046
      Printed circuit board assembly recommendations for STMicroelectronics PowerFLAT packages
      4.0
      4.82 MB
      PDF
      AN5336
      ST8500 host interface driver
      1.0
      978.47 KB
      PDF
      AN2946
      Solar-LED streetlight controller with 25 W LED lamp driver and 85 W battery charger based on the STM32F101Rx
      2.4
      1.22 MB
      PDF
      AN4461

      100 W LED street lighting application using STLUX385A

      AN5316

      35 W wide input range flyback converter using HVLED001B quasi resonant Flyback controller and STF10LN80K5

      AN3105

      48 V - 130 W high efficiency converter with PFC for LED street lighting applications - European version

      AN3106

      48 V - 130 W high-efficiency converter with PFC for LED street lighting applications

      AN2644

      An introduction to LLC resonant half-bridge converter

      AN4656

      Bootloading procedure for STLUX™ and STNRG™ digital controllers

      AN2983

      Constant current inverse buck LED driver using L6562A

      AN2680

      Fan speed controller based on STDS75 or STLM75 digital temperature sensor and ST72651AR6 MCU

      AN4250

      Fishbone diagram for power factor correction

      AN4539

      HRTIM cookbook

      AN4932

      HVLED001A - enhanced QR high power factor flyback controller for LED drivers

      AN4885

      High brightness LED dimming using the STM32F334 Discovery kit

      AN5119

      How to design an application from draft with STNRG011

      AN2648

      Increasing the resolution of analog temperature sensors

      AN2450

      LLC resonant half-bridge converter design guideline

      AN4406

      MDmesh™ M2: the new ST super-junction technology ideal for resonant topologies

      AN5046

      Printed circuit board assembly recommendations for STMicroelectronics PowerFLAT packages

      AN5336

      ST8500 host interface driver

      AN2946

      Solar-LED streetlight controller with 25 W LED lamp driver and 85 W battery charger based on the STM32F101Rx

    • Description バージョン サイズ アクション
      UM1736
      Getting started with STM32F334 discovery kit software development tools
      1.1
      2.18 MB
      PDF
      UM1735
      Discovery kit for STM32F3 series with STM32F334C8 MCU
      2.0
      1.61 MB
      PDF
      UM1733
      Getting started with STM32F334 Discovery kit
      1.1
      351.28 KB
      PDF
      UM1736

      Getting started with STM32F334 discovery kit software development tools

      UM1735

      Discovery kit for STM32F3 series with STM32F334C8 MCU

      UM1733

      Getting started with STM32F334 Discovery kit

    • Description バージョン サイズ アクション
      DN0028
      STEVAL-ILL066V1 - 90Vac-305Vac input
      1.0
      583.39 KB
      PDF
      DN0028

      STEVAL-ILL066V1 - 90Vac-305Vac input

プレゼンテーション & トレーニング資料

    • Description バージョン サイズ アクション
      Smart street lighting solutions 2.1
      1.56 MB
      PDF

      Smart street lighting solutions

Publications and Collaterals

    • Description バージョン サイズ アクション
      600-650 V MDmesh™ M2: The ST’s new Super-junction HV MOSFET series 1.0
      671.31 KB
      PDF
      DC-DC converters
      557.92 KB
      PDF
      HVLED: Lighting the future 12.2018
      700.32 KB
      PDF
      L6984, L6986 Energy saving synchronous DC-DC converters for industrial
      1.24 MB
      PDF
      STLUX385A 100 W LED street lighting 1.0
      2.02 MB
      PDF
      STLUX: Intelligent lighting made easy 07.2017
      280.46 KB
      PDF
      STTS75 2.2
      706.56 KB
      PDF

      600-650 V MDmesh™ M2: The ST’s new Super-junction HV MOSFET series

      DC-DC converters

      HVLED: Lighting the future

      L6984, L6986 Energy saving synchronous DC-DC converters for industrial

      STLUX385A 100 W LED street lighting

      STLUX: Intelligent lighting made easy

      STTS75

    • Description バージョン サイズ アクション
      Linear and Switching Voltage Regulators Selection Guide 3.0
      370.88 KB
      PDF

      Linear and Switching Voltage Regulators Selection Guide

    • Description バージョン サイズ アクション
      スマート・インダストリ向け 製品 &amp; ソリューション ガイド 3.1
      3.41 MB
      PDF

      スマート・インダストリ向け 製品 &amp; ソリューション ガイド

開発ツール・ハードウェア

ソフトウェア製品

    • 製品型番

      Graphical user interface for the STEVAL-PCC020V1 USB to I²C/UART interface board for STNRG011

    • 製品型番

      Fan speed controller based on STDS75 or STLM75 digital temperature sensor and ST72651AR6 MCU

eDesignSuite

LEDドライバ

Input

V This option is required. And must be less than or equal to Volt. Max [V]
V This option is required. And must be greater than or equal to Volt. Min [V]

LED custom

V This option is required.
A This option is required.
Ω This option is required.

LEDs

This option is required. And must be a whole positive number between 1 and 20.
This option is required. And must be a whole positive number between 1 and 20.

Amplifiers and Comparators

Part number Description
TSV911 Wide-bandwidth (8MHz) rail to rail input/output 5V CMOS Op-Amp, single
TSZ121 Very high accuracy (5 uV) zero drift 5 V CMOS Op-Amp, single, GBP=400kHz
TSZ181 Very high accuracy (25 uV) zero drift 5V CMOS Op-Amps
TSZ182 Very high accuracy (25 uV) zero drift 5V CMOS Op-Amps
Part number
Wide-bandwidth (8MHz) rail to rail input/output 5V CMOS Op-Amp, single
Very high accuracy (5 uV) zero drift 5 V CMOS Op-Amp, single, GBP=400kHz
Very high accuracy (25 uV) zero drift 5V CMOS Op-Amps
Very high accuracy (25 uV) zero drift 5V CMOS Op-Amps

MEMS and Sensors

Part number Description
LM135 Precision Temperature Sensor
LM235 Precision Temperature Sensor
LM335 Precision Temperature Sensor
STDS75 Digital temperature sensor and thermal watchdog
STLM20 Analog temperature sensor, ultra-low current 2.4 V, high precision
STLM75 High-precision digital temperature sensor and thermal watchdog
STTS2004 2.2 V memory module temperature sensor with a 4 Kb SPD EEPROM
STTS75 Digital temperature sensor and thermal watchdog, delta-sigma analog-to-digital (ADC) converter, I2C interface
STTS751 2.25 V low-voltage local digital temperature sensor
Part number
Precision Temperature Sensor
Precision Temperature Sensor
Precision Temperature Sensor
Digital temperature sensor and thermal watchdog
Analog temperature sensor, ultra-low current 2.4 V, high precision
High-precision digital temperature sensor and thermal watchdog
2.2 V memory module temperature sensor with a 4 Kb SPD EEPROM
Digital temperature sensor and thermal watchdog, delta-sigma analog-to-digital (ADC) converter, I2C interface
2.25 V low-voltage local digital temperature sensor

Power Management

Part number Description
HVLED001A Offline controller for LED lighting with constant voltage primary-sensing and high power factor
HVLED001B High power factor flyback controller with constant voltage primary sensing and ultra low standby consumption
HVLED002 High performance current mode LED controller
HVLED805 Off-line LED driver with primary-sensing up to 5W
L6562A Transition-mode PFC controller BCD technology
L6562AT Transition-mode PFC controller
L6563 Advanced transition-mode PFC controller
L6563H High voltage start-up transition-mode PFC
L6563S Enhanced transition-mode PFC controller
L6564 10 pin transition-mode PFC controller
L6564H High voltage start-up transition-mode PFC
L6564T 10 pin transition-mode PFC controller for outdoor applications
L6599A Improved high-voltage resonant controller
L6599AF Ultra-extreme temperature range improved high voltage resonant controller
L6599AT IMPROVED HIGH-VOLTAGE RESONANT CONTROLLER
L6699 Enhanced high-voltage resonant controller
L6985F 38 V 500 mA synchronous step-down switching regulator with 30 uA quiescent current
L6986 38 V 2 A synchronous step-down switching regulator with 30 uA quiescent current
L6986F 38 V 1.5 A synchronous step-down switching regulator with 30 uA quiescent current
L7987 61 V 3 A asynchronous step-down switching regulator with adjustable current limitation
L7987L 61 V 2 A asynchronous step-down switching regulator with adjustable current limitation
SRK2000A Synchronous rectifier smart driver for LLC resonant converters
SRK2001A Adaptive synchronous rectification controller for LLC resonant converter
ST1S14 Up to 3 A step down switching regulator
ST1S40 3A DC step-down switching regulator
ST1S41 4 A step-down switching regulator
STCMB1 TM PFC with X-cap discharge and LLC resonant combo controller
STLUX285A Digital controllers for lighting and power conversion applications with up to 6 programmable PWM generators, 96 MHz PLL, DALI
STLUX325A Digital controllers for lighting and power conversion applications with up to 6 programmable PWM generators, 96 MHz PLL, DALI
STLUX385A Digital controllers for lighting and power conversion applications with up to 6 programmable PWM generators, 96 MHz PLL, DALI
STNRG011 Digital combo multi-mode PFC and time-shift LLC resonant controller
Part number
Offline controller for LED lighting with constant voltage primary-sensing and high power factor
High power factor flyback controller with constant voltage primary sensing and ultra low standby consumption
High performance current mode LED controller
Off-line LED driver with primary-sensing up to 5W
Transition-mode PFC controller BCD technology
Transition-mode PFC controller
Advanced transition-mode PFC controller
High voltage start-up transition-mode PFC
Enhanced transition-mode PFC controller
10 pin transition-mode PFC controller
High voltage start-up transition-mode PFC
10 pin transition-mode PFC controller for outdoor applications
Improved high-voltage resonant controller
Ultra-extreme temperature range improved high voltage resonant controller
IMPROVED HIGH-VOLTAGE RESONANT CONTROLLER
Enhanced high-voltage resonant controller
38 V 500 mA synchronous step-down switching regulator with 30 uA quiescent current
38 V 2 A synchronous step-down switching regulator with 30 uA quiescent current
38 V 1.5 A synchronous step-down switching regulator with 30 uA quiescent current
61 V 3 A asynchronous step-down switching regulator with adjustable current limitation
61 V 2 A asynchronous step-down switching regulator with adjustable current limitation
Synchronous rectifier smart driver for LLC resonant converters
Adaptive synchronous rectification controller for LLC resonant converter
Up to 3 A step down switching regulator
3A DC step-down switching regulator
4 A step-down switching regulator
TM PFC with X-cap discharge and LLC resonant combo controller
Digital controllers for lighting and power conversion applications with up to 6 programmable PWM generators, 96 MHz PLL, DALI
Digital controllers for lighting and power conversion applications with up to 6 programmable PWM generators, 96 MHz PLL, DALI
Digital controllers for lighting and power conversion applications with up to 6 programmable PWM generators, 96 MHz PLL, DALI
Digital combo multi-mode PFC and time-shift LLC resonant controller

Power Transistors

Part number Description
STF13N60M2 N-channel 600 V, 0.35 Ohm typ., 11 A MDmesh M2 Power MOSFET in TO-220FP package
STF15N65M5 N-channel 650 V, 0.308 Ohm typ., 11 A MDmesh M5 Power MOSFET in TO-220FP package
STF16N60M2 N-channel 600 V, 0.28 Ohm typ., 12 A MDmesh M2 Power MOSFET in TO-220FP package
STF18N60M2 N-channel 600 V, 0.255 Ohm typ., 13 A MDmesh M2 Power MOSFET in TO-220FP package
STF18N65M5 N-channel 650 V, 0.198 Ohm typ., 15 A MDmesh M5 Power MOSFET in TO-220FP package
STL4N10F7 N-channel 100 V, 0.062 Ohm typ., 4.5 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package
STL7N10F7 N-channel 100 V, 0.027 Ohm typ., 7 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package
Part number
N-channel 600 V, 0.35 Ohm typ., 11 A MDmesh M2 Power MOSFET in TO-220FP package
N-channel 650 V, 0.308 Ohm typ., 11 A MDmesh M5 Power MOSFET in TO-220FP package
N-channel 600 V, 0.28 Ohm typ., 12 A MDmesh M2 Power MOSFET in TO-220FP package
N-channel 600 V, 0.255 Ohm typ., 13 A MDmesh M2 Power MOSFET in TO-220FP package
N-channel 650 V, 0.198 Ohm typ., 15 A MDmesh M5 Power MOSFET in TO-220FP package
N-channel 100 V, 0.062 Ohm typ., 4.5 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package
N-channel 100 V, 0.027 Ohm typ., 7 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package