产品概述
描述
The TSC103 measures a small differential voltage on a high-side shunt resistor and translates it into a ground-referenced output voltage. The gain is adjustable to four different values from 20 V/V up to 100 V/V by two selection pins.
Wide input common-mode voltage range, low quiescent current, and tiny TSSOP8 packaging enable use in a wide variety of applications.
The input common-mode and power-supply voltages are independent. The common-mode voltage can range from 2.9 V to 70 V in the single-supply configuration or be offset by an adjustable voltage supplied on the Vcc- pin in the dual-supply configuration.
With a current consumption lower than 360 μA and a virtually null input leakage current in standby mode, the power consumption in the applications is minimized.
-
所有功能
- Independent supply and input common-mode voltages
- Wide common-mode operating range: 2.9 V to 70 V in single-supply configuration,-2.1 V to 65 V in dual-supply configuration
- Wide common-mode surviving range: -16 V to 75 V (reversed battery and load-dump conditions)
- Supply voltage range: 2.7 to 5.5 V in single-supply configuration
- Low current consumption: ICCmax = 360 μA
- Pin selectable gain: 20 V/V, 25 V/V, 50 V/V or 100 V/V
- Buffered output
电路原理图
eDesignSuite
eDesignSuite is a comprehensive set of easy-to-use design-aid utilities ready to help you streamline the system development process with a wide range of ST products.
Power Management Design Center
Thermal-electrical Simulators for Components
Signal Conditioning Design Tool
NFC/RFID Calculators
Power Supply Design Tool
SMPS design, by topology, by type and by product PFC design with analog and digitial control Supports various PCB configurations 
LED Lighting Design Tool
Handles AC-DC and DC-DC design in common topologies Displays interactive and annotated schematic Provides current/voltage graphs, Bode plots, efficiency curves and power-loss data 
Digital Power Workbench
Provides a step-by-step optimized design of power section and control loop Generates the STM32Cube embedded software package for custom applications and allows firmware project generation, compatible with multiple STM32 IDEs 
Power Tree Designer
Specify input/output power for each node in the tree Check for consistency Design each individual node 
AC Switches Simulator
Select ratings and application waveforms Get junction temperature and blocking voltage graphs Search and sort suitable devices 
Rectifier Diodes Simulator
Select ratings and application waveforms Estimate power losses Search and sort suitable devices 
STPOWER Studio
Supports long mission profiles Provides power loss and temperature graphs Helps define heatsink thermal properties 
Twister Sim
Help select the right ViPOWER Automotive power device Supports load-compatibility, wiring harness optimization, fault condition impact and diagnostic analysis Supports various PCB configurations 
TVS Simulator
Specify system ratings and surge waveform Search and sort suitable devices 
Estimate
Build simple schematics and firmware inputs in minutes Quickly generate reliable estimates of: Battery life System power consumption Bill of materials costs 
Active Filters
Handles multi-stage-designs and common topologies Returns circuit component values Provides gain, phase and group delay graphs Low Pass, High Pass and Band Pass 
Comparators
Handles most common configurations Returns circuit components values Provides I/O signal waveforms Inverting, Non Inverting, Window 
Low side Current Sensing
Returns circuit component values Provides current error graphs 
High side Current Sensing
Provides current error graphs. Help to select the right High side current sensing and shunt devices. 
NFC Inductance
Input geometry and substrate properties Get antenna impedance 
UHF Link Budget
Enter forward and reverse link characteristics The tool returns link budget estimate 
NFC Tuning Circuit
Enter antenna parameter and matching target Select the topology of the matching network The tool returns component values for the desired design targets 特别推荐
EDA符号、封装和3D模型
STMicroelectronics - TSC103
Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.
Please select one model supplier :
符号
封装
3D模型
全部资源
| 资源标题 | 版本 | 更新时间 |
|---|
SPICE models (1)
| 资源标题 | 版本 | 更新时间 | ||
|---|---|---|---|---|
| MOD | 2.0 | 03 Nov 2020 | 03 Nov 2020 |
Eldo models (1)
| 资源标题 | 版本 | 更新时间 | ||
|---|---|---|---|---|
| MOD | 2.0 | 03 Nov 2020 | 03 Nov 2020 |
质量与可靠性
| 产品型号 | Marketing Status | 封装 | 等级规格 | 符合RoHS级别 | 材料声明** |
|---|---|---|---|---|---|
| TSC103IDT | 批量生产 | SO-8 | 工业 | Ecopack3 | |
| TSC103IPT | 批量生产 | TSSOP-8L | 工业 | Ecopack3 | |
| TSC103IYDT | 批量生产 | SO-8 | 汽车应用 | Ecopack3 | |
| TSC103IYPT | 批量生产 | TSSOP-8L | 汽车应用 | Ecopack3 |
(**) st.com上提供的材料声明表单可能是基于包装系列中最常用的封装的通用文档。因此，它们可能不是100%适用于特定的设备。有关特定设备的信息，请联系 销售支持。
样片和购买
| 产品型号 | 供货状态 | Budgetary Price (US$)*/Qty | 从ST订购 | Order from distributors | 封装 | 包装类型 | RoHS | Country of Origin | ECCN (US) | ECCN (EU) | 温度（ºC） | Operating Temperature (°C) (min) | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 最小值 | 最大值 | |||||||||||||
| TSC103IYPT | | | distributors 无法联系到经销商，请联系我们的销售办事处 | TSSOP-8L | Tape and Reel | CHINA | EAR99 | NEC | -40 | 125 | -40 | |||
| TSC103IDT | | | distributors 无法联系到经销商，请联系我们的销售办事处 | SO-8 | Tape and Reel | MOROCCO | EAR99 | NEC | -40 | 125 | -40 | |||
| TSC103IPT | | | distributors 无法联系到经销商，请联系我们的销售办事处 | TSSOP-8L | Tape and Reel | MOROCCO | EAR99 | NEC | -40 | 125 | -40 | |||
| TSC103IYDT | | | distributors 无法联系到经销商，请联系我们的销售办事处 | SO-8 | Tape and Reel | MOROCCO | EAR99 | NEC | -40 | 125 | -40 | |||
TSC103IYPT 批量生产
TSC103IDT 批量生产
TSC103IPT 批量生产
TSC103IYDT 批量生产