LED车前大灯

主要特性

• Simple single IC application board dedicated for VN7010AJ
• Provides electrical connectivity and thermal heat-sinking for easy prototyping
• General device features
  • Single channel smart high-side driver with MultiSense analog feedback
  • Very low standby current
  • Compatible with 3 V and 5 V CMOS outputs
• Diagnostic functions
  • Multiplexed analog feedback of: load current with high precision proportional current mirror, V_CC supply voltage and T_CHIP device temperature
  • Overload and short to ground (power limitation) indication
  • Thermal shutdown indication
  • OFF-state open-load detection
  • Output short to V_CC detection
  • Sense enable/disable
• Protections
  • Undervoltage shutdown
  • Overvoltage clamp
  • Load current limitation
  • Self limiting of fast thermal transients
  • Configurable latch-off on overtemperature or power limitation with dedicated fault reset pin
  • Loss of ground and loss of V_CC
  • Reverse battery with external components
  • Electrostatic discharge protection

Show More

主要特性

• Complete AIS3624DQ pin-out for a standard DIL24 socket
• Fully compatible with STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

主要特性

• Input voltage 5 V
• 12 V output, step-up converter for transceiver supply voltage
• LIN transceiver
• CAN transceiver
• Automotive-grade ESD protection
• IEC61000-4-2 compatibility

Show More

主要特性

• SPC582B 32-bit z2 core @80Mhz CPU, 32-bit Power Architecture^® Technology CPU, 1MB Code Flash in eQFP64 package.
• On-board USB-JTAG PLS debugger and dedicated optional connector to plug a stand-alone JTAG debugger.
• USB Virtual Communication port.
• Two types of extension resources:
  • Arduino Uno Revision 3 connectivity
  • Extension headers for all device pins and for quick connection to prototyping expansion boards, additional modules and evaluation probing.
• Flexible board power supply:
  • USB port (mini B - 5V)
  • external sources (DC): 7÷12 V, 5V or 3.3V and 5V
• Two push buttons: USER and RESET
• Eight LEDs
  • 3 Integrated Programmer/Debugger
  • 3 LEDs User
  • 1 Reset
  • 1 Power LED: +5V
• 40MHz Crystal

Show More

主要特性

• SPC58EC80E5 is a 32-bit Power Architecture®e200z4d dual core, 4224 kB flash + 128 kB data flash) in eTQFP144.
• Integrated programmer - debugger.
• JTAG interface (Standard 7x2 male 100mil).
• 2 ISO CAN FD port (DB9 connector).
• 1 Ethernet port.
• 1 FlexRay, 1 LIN (with transceiver).
• 1 USB virtual COM Port.
• Connectors Arduino UNO R3-compatible.
• 3 Push buttons, 3 LEDs for user purpose.
• 2 potentiometers for ADC quick evaluation.
• Reset push button.
• All GPIOs and signals accessible by a 4x37 0.1" pin grid array allowing connection of the additional boards.
• 12MHz crystal.
• Board Supply: 12 VDC (external power
• supply).
• Board size 150 x 101 mm.

Show More

主要特性

• Featuring SPC58NG84E7, a 32-bit Power Architecture® triple core e200z4, 6MB flash in eLQFP176 package. Device designed to meet ASIL-D safety level and embeds an HSM with 128KB flash memory.
• 2 Ethernet ports
• 1 CAN FD port (DB9 connector)
• JTAG interface (14 pin - 2x7 connector)
• 2 Push buttons, 4 LEDs for user purposes, reset push button
• Board Supply: 12 VDC (external power supply)
• Connector suitable for TFT LCD module
• Board size 145 x 105 mm

Show More

主要特性

• Immediate evaluation of Voltage Regulators, Power Management and Multichannel Power Management with a selection of samples.
• The kit includes
  • 10 samples

Show More

主要特性

• Simple single IC application board dedicated for VNH7100BAS
• Provides electrical connectivity and thermal heat-sinking for easy prototyping

Show More

主要特性

• 2 soldered L99LD21 flexible LED drivers
• Board size 100 x 55 mm
• Two extension headers (2 x 36 pin - 100 mil) for quick connection to SPC560B-DIS discovery board
• Controllable by dedicated GUI available on www.st.com
• Free ready to run application firmware available on www.st.com, to support quick evaluation and development

Show More

主要特性

• Board functionality based on L99SM81V programmable stepper motor driver for automotive applications:
  • with micro-stepping and hold functions
  • BEMF monitoring for stall detection
  • programmable configuration via SPI
  • 5 V internal linear voltage regulator (output available on board connector)
• Board reverse battery protection with STD95N4F3 MOSFET, which can be substituted with two optionally mounted diodes and a jumper
• Input operating voltage range from 6 V to 28 V
• Output current up to 1.35 A
• Board size: 65 mm length x 81 mm width x 11 mm maximum component height
• WEEE and RoHS compliant
• All ST components are qualified Automotive grade
• Part of the AutoDevKit™ initiative
• Applications: automotive bipolar stepper motor

Show More

主要特性

• Two embedded L99LD21 high power LED drivers able to supply four independent channels
• Output current up to 1.69 A each channel
• Input operating voltage range from 5.5 V to 24 V
• Programmable via SPI, allowing accurate LED current setting
• Protections and diagnostics for output short-circuit and open-load, overtemperature, and battery undervoltage.
• Automotive Limp-Home Mode support
• Board size: 81 x 100 mm. Maximum components height: 11 mm
• WEEE and RoHS compliant
• All ST components are qualified Automotive grade
• Board designed according to the AutoDevKit initiative

Show More

主要特性

• Designed to connect the following elements for a complete automatic front lighting (AFL) adjustment solution for a LED vehicle headlight:
  • An MCU board such as the AEK-MCU-C4MLIT1 with 4x37 connector
  • Two AEK-MOT-SM81M1 stepper motor boards
  • An AEK-LED-21DISM1 LED driver control board with two L99LD21 LED drivers and providing four independent channels
  • An EV-VNx actuator board such as the EV-VN7050AS to switch a headlight colling fan on and off
• Connected boards are controlled via three separate SPIs
• Input voltage from 8 V_DC to 15 V_DC
• Board size: 65 x 100 mm. Maximum component height: 27 mm
• Cables included for two stepper motor boards and one LED driver board
• WEEE and RoHS compliant
• All ST components are qualified Automotive grade
• Part of the AutoDevKit initiative

Show More

主要特性

• Complete AIS328DQ pinout for a standard DIL 24 socket
• Fully compatible with the STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

主要特性

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F103RET6 high-performance ARM Cortex^™ -M3 microcontroller
• Includes a DIL24 socket for easy MEMS adapter connection
• 3 V on-board linear voltage regulator
• DFU compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Debugging connector for SWD/JTAG
• RoHS compliant

Show More

主要特性

• Complete A3G4250D pinout for a standard DIL 24 socket
• Fully compatible with the STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

主要特性

• Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board.
• Supports SPC5x MCUs
• Supports Multicore, eTPU and GTM debugging
• Includes FLASH programming capability
• Support service provided through STMicroelectronics

Show More

主要特性

• SPC560B54L5 32-bit 48 MHz e200z0h CPU, 32-bit Power Architecture® Technology CPU, 768 kB Code Flash in an LQFP144 package.
• On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers.
• Board power supply: through external +12 V PSU or from the USB bus (5 V supply voltage).
• Seven LEDs: D6 for 5 V power on,D2 for Reset, D101, D102, D103 for PLS debugger section, D7 and D8 for PC3 and PC2 outputs
• Two push buttons (reset and user)
• A potentiometers for ADC input (user)
• Two extension headers (2 x 36 pin - 100 mil) for all LQFP144 pins and for quick connection to prototyping boards, additional modules and easy probing.
• JTAG interface (2 x 7 male 100mil connector)
• USB port (mini -B)
• 16 MHz crystal
• Specification:
  • Board size 100 x 65 mm
  • MCU: SPC560B54L5 - LQFP144
  • 2 extension headers 2 x 36 pin - 100 mil
  • DC connector (+12 V input)
  • Mini USB - B
  • JTAG 2 x 7 - 100 mil connector

Show More