鼠标

主要特性

• Bluetooth^® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
• Associated BlueNRG-2 development kit SW package including firmware and documentation
• Up to +8 dBm available output power (at antenna connector)
• Excellent receiver sensitivity (-88 dBm)
• Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
• Bluetooth^® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
• New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
• SMA connector for antenna or measuring equipment
• 3 user LEDs
• 2 user buttons
• 3D digital accelerometer and 3D digital gyroscope
• MEMS pressure sensor with embedded temperature sensor
• RoHS compliant

Show More

主要特性

• Bluetooth^® SMART board based on the BlueNRG-1 Bluetooth low energy system on chip
• Associated BlueNRG-1 development kit SW package including firmware and documentation
• Up to +8 dBm available output power (at antenna connector)
• Excellent receiver sensitivity (-88 dBm)
• Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
• Bluetooth^® low energy compliant, supports master, slave and simultaneous master-and-slave roles
• New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
• SMA connector for antenna or measuring equipment
• 3 user LEDs
• 2 user buttons
• 3D digital accelerometer and 3D digital gyroscope
• MEMS pressure sensor with embedded temperature sensor
• Battery holder
• JTAG debug connector
• USB to serial bridge for providing I/O channel with the BlueNRG-1 device
• Jumper for measuring current for BlueNRG-1 only
• RoHS compliant

Show More

主要特性

• Two ready-to-use printed circuit boards (PCB):
  • ST25DV_Discovery_Mboard:
  • STM32F405VGT6 LQFP100 32-bit microcontroller, with 1 Mbyte Flash memory, 192 + 4 Kbytes SRAM.
  • LCD color screen (320 x 200 pixels)
  • Touch screen driver
  • Different color LEDs (power, user, ST link)
  • User push button
  • Joystick for menu selection
  • Reset button
  • On board ST link for microcontroller firmware upgrade and debug
  • ST link mini USB
  • User micro USB
  • USB micro or mini connector for board powering
  • Demonstration use cases stored in memory
  • Demonstration edition (optional add-on module) with Bluetooth Low Energy module, Wi-Fi^® module and JTAG 20 pin connector
• ST25DV_Discovery_ANT_C5:
  • 40 mm x 24 mm, 13.56 MHz inductive antenna etched on the PCB
  • ST25DV04K Dynamic NFC / RFID tag
  • I² C interface connector
  • Energy harvesting output (VOUT) with a 10 nF capacitance filtering circuit
  • GPO configurable as RF WIP/BUSY output, to indicate that an RF operation is ongoing

Show More

主要特性

• Common features
  • STM32 microcontroller in LQFP64 package
  • 1 user LED shared with Arduino™
  • 1 user and 1 reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External SMPS to generate V_core logic supply
  • 24 MHz HSE
  • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI^® debug connector
  • Arm^® Mbed Enabled™ compliant

Show More

主要特性

• M24SR64-Y Dynamic NFC/RFID tag IC
• NFC antenna: 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• Powered through the Arduino UNO R3 connectors
• 3 color LEDs for general purpose

Show More

主要特性

• Ready-to-use printed circuit board (PCB) including:
  • M24SR64-Y Dynamic NFC/RFID tag
  • 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
  • STM32F103RGT6 64LQFP 32-bit microcontroller, with 1Mbytes of Flash memory
  • LCD Color Screen (320*200 pixels)
  • Different color LEDs
  • USB microB connector for board powering
  • JTAG connector for microcontroller firmware upgrade and debug
  • Joystick for menu selection
• M24SR-DISCO-PREM specific features:
  • Bluetooth module with audio outputs connected to Jack 3.5
  • Headset

Show More

主要特性

• The following ST MEMS sensors are mounted:
  • LSM6DSL 6-axis inertial module
  • LIS2MDL Magnetic sensor
  • LPS22HB Pressure sensor
  • HTS221 Humidity and Temperature sensor
  • MP34DT05-AMicrophone
• VL53L0X gesture detector
• Based on STM32F412C microcontroller

Show More