打印机

主要特性

• STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory and 324 Kbytes of RAM in BGA216 package
• On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
  • Mbed-enabled (mbed.org)
  • USB functions: USB virtual COM port, mass storage, debug port
• 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive touch screen
• SAI Audio DAC, with a stereo headphone output jack
• 3 MEMS microphones
• MicroSD card connector
• I2C extension connector
• 4Mx32bit SDRAM
• 128-Mbit Quad-SPI NOR Flash
• Reset and wake-up buttons
• 4 color user LEDs
• USB OTG FS with Micro-AB connector
• Three power supply options:
• Expansion connectors and Arduino^™ UNO V3 connectors
• Comprehensive free software including a variety of examples, part of STM32Cube package
• Supported by a wide choice of integrated development environments

Show More

主要特性

• M24SR64-Y Dynamic NFC/RFID tag IC
• NFC antenna: 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• Powered through the Arduino UNO R3 connectors
• 3 color LEDs for general purpose

Show More

主要特性

• Input voltage from 8 to 48 V
• Peak output current up to 6 A
• Enable/Disable/Fault flag pin
• Adjustable undervoltage lockout
• Adjustable output voltage clamp
• Programmable V_OUT slew rate control
• Latch or auto-retry jumper-programmable thermal protection
• Power good monitoring flag
• Drives an optional external reverse current protection MOSFET
• CE certified
• RoHS and China RoHS compliant
• WEEE compliant (2012/19/UE RAEE II)

Show More

主要特性

• Common features
  • STM32 microcontroller in LQFP144 package
  • 3 user LEDs
  • 2 user and reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:SWDST Zio expansion connector including Arduino™ Uno V3ST morpho expansion connector
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External or internal SMPS to generate V_core logic supply
  • Ethernet compliant with IEEE-802.3-2002
  • USB OTG full speed or device only
  • Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45
  • Arm^® Mbed Enabled™ compliant

Show More

主要特性

• On-board NFC card reader IC: ST25R3911B
• 47 mm x 34 mm, four turns, 13.56 MHz inductive antenna etched on PCB and associated tuning circuit
• Six general purpose LEDs
• ISO 18092 (NFCIP-1) active P2P
• ISO 14443A and ISO14443B
• ISO 15693
• FeliCa™
• VHBR
  • 6.8 Mbit/s AFE and PCD to PICC framing
  • 3.4 Mbit/s PICC to PCD framing
• Up to 1.4 W output power with differential antenna
• Possibility of driving two antennas in single ended configuration
• Inductive and capacitive wake-up
• Automatic antenna tuning system
• Transparent and Stream modes to implement MIFARE™ Classic compliant or other custom protocols
• Equipped with Arduino™ UNO R3 connector
• Free comprehensive development firmware library compatible with STM32Cube and samples for ST25R3911B
• Scalable solution for multiple board cascade
• FCC certified
• RoHS compliant

Show More

主要特性

• Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
• Up to 4-Kbit memory with NDEF support
• 54 mm diameter, single layer circular antenna
• Compatible with STM32 Nucleo boards
• Equipped with Arduino™ UNO R3 connector
• Self-powered or powered through the Arduino™ UNO R3 connectors
• Three general purpose LEDs
• Scalable solution, capable of cascading multiple boards for larger systems
• Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
• FCC and IC verified
• RoHS compliant

Show More

主要特性

• STM32F769NIH6 microcontroller featuring 2 Mbytes of Flash memory and 512+16+4 Kbytes of RAM, in BGA216 package
• On-board ST-LINK/V2-1 supporting USB reenumeration capability
• USB ST-LINK functions: virtual COM port, mass storage, debug port
• 4" capacitive touch LCD display with MIPI® DSI connector (on STM32F769I-DISCO only)
• SAI audio codec
• Two audio line jacks, one for input and one for output
• Stereo speaker outputs
• Four ST MEMS microphones on DFSDM inputs
• Two SPDIF RCA input and output connectors
• Two push-buttons (user and reset)
• 512-Mbit Quad-SPI Flash memory
• 128-Mbit SDRAM
• Connector for microSD card
• Wi-Fi or Ext-EEP daughterboard connector
• USB OTG HS with Micro-AB connector
• Ethernet connector compliant with IEEE-802.3-2002
• Five power supply options:
  • ST LINK/V2-1
  • USB HS connector
  • 5 V from RJ45 (Power Over Ethernet)
  • 5 V from Arduino^™ or external connector
  • USB charger
• Power Over Ethernet based on IEEE 802.3af (Powered Device, 48 V to 5 V, 3 W)
• Power supply output for external applications: 3.3 V or 5 V
• Arduino^™ Uno V3 connectors
• Comprehensive free software including a variety of examples, part of the STM32Cube package
• Supported by a wide choice of integrated development environments

Show More