概述
解决方案
硬件评估工具
资源
工具和软件
主要产品
开始
产品型号
描述
P-NUCLEO-IOM01M1 STM32 Nucleo pack for IO-Link master with IO-Link v1.1 PHY and stack Quick view

主要特性

  • STEVAL-IOM001V1
    • IO-Link master PHY based on L6360
    • Interrupt diagnostics pin
    • I²C and UART interface
    • SPI (slave) interface
    • 65 mA selectable (3.3 or 5.0 V) linear regulator
    • CQ (push-pull) and L+ (high side) switches
    • IQ additional IEC61131-2 type 1 digital input
    • L+ and CQ overload and overheating protections with non-dissipative cut-off function
    • QFN-26L (3.5x5x1 mm) package
    • Operating voltage range from 18 to 32.5 V
    • Additional high side switch for L+ heavy loads (IPS161H)
    • LEDs for status and diagnostics
    • Ground and VCC wire break protections
    • EMC compliance with IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
    • Equipped with ST morpho connectors
    • CE certified
    • RoHS and China RoHS compliant
  • NUCLEO-F446RE
    • STM32F446RET6 32-bit Micro-controller based on ARM® Cortex® -M4 core (180 MHz max.) with 512-Kbyte Flash memory and 128 (+4) Kbyte RAM
    • Two types of extension resources: Arduino™ UNO Revision 3 connectivity and ST morpho extension pin headers for full access to all STM32 I/Os
    • Mbed-enabled (http://mbed.org)
    • On-board ST-LINK/V2-1 debugger/programmer with SWD connector: selection-mode switch to use the kit as a standalone ST-LINK/V2-1
    • Two push-buttons: USER and RESET

Show More

P-NUCLEO-IOD01A1 STM32 Nucleo pack for IO-Link device fully compatible with IO-Link v1.1 (PHY and stack) Quick view

主要特性

  • Equipped with Arduino UNO R3 connectors and compatible with STEVAL-IOD003V1, X-NUCLEO-IKS01A2 and NUCLEO-L073RZ boards.
  • The STEVAL-IOD003V1 features:
    • IO-Link (PHY) device layer based on L6362A
    • Operating voltage range 6.5 to 35 V
    • Dedicated CQ overload pin (wake-up)
    • Diagnostics pin (UVLO, overtemperature and cut-off)
    • UART interface
    • Linear regulators for independent supply from +24 V bus (12 mA 3.3 V and 100 mA 12 V)
    • LEDs for status and diagnostics
    • Overload and overheating protections with non-dissipative cut-off function
    • Full reverse polarity on IO-Link interface pins
    • EMC protections according to IO-Link v1.1 and IEC 60947-5-2
    • Ground and VCC wire break protections
  • The X-NUCLEO-IKS01A2 features:
    • LSM6DSL 3D accelerometer and 3D gyroscope
    • LSM303AGR 3D accelerometer and 3D magnetometer
    • LPS22HB pressure sensor
    • HTS221 capacitive digital relative humidity and temperature
    • DIL24 socket for additional MEMS adapters and other sensors
    • Free comprehensive development firmware library and samples for all sensors compatible with STM32Cube firmware
  • The NUCLEO-L073RZ features:
    • STM32L073RZT6 32-bit microcontroller based on ARM® Cortex® -M0+ core
    • Pre-programmed IO-Link device stack (v1.1 compatible)
    • Arduino UNO R3 connectivity and ST morpho extension pin headers
    • Mbed-enabled (http://mbed.org)
    • On-board ST-LINK/V2-1 debugger/programmer with SWD connector

Show More

STEVAL-IDP004V1 IO-Link master multi-port evaluation board based on L6360 Quick view

主要特性

  • Main supply voltage 32 V maximum
  • 4 L6360 IO-Link master devices
  • RS-485 serial interface
  • CAN serial interface
  • USB interface
  • DC-DC converter
  • On-board reverse polarity protection
  • Designed to meet IEC requirement for industrial standards
  • RoHS and WEEE compliant

Show More

STEVAL-IDP003V1 IO-Link industrial modular sensor board based on L6362A Quick view

主要特性

  • Main supply voltage: 32 V maximum
  • STM32L071CZ microcontroller
  • IO-Link PHY using the L6362A device for data communication with host unit
  • DC-DC converter and linear regulator on board
  • Integrated reverse polarity protection on L6362A ICs
  • Multi-sensor connection
  • 400 kHz I²C communication
  • PCB designed to accept real industrial sensors (8 mm x 70 mm, with 0.8 mm thickness)
  • Designed to meet IEC industrial standard requirements
  • RoHS compliant

Show More

STEVAL-IFP017V3 Evaluation board for IO-Link transceiver device L6362A Quick view

主要特性

  • Operating voltage from 7 to 36 V
  • Operating current up to 300 mA
  • Configurable in push-pull, high-side or low-side
  • Overcurrent protection with cutoff function
  • Overtemperature protection
  • Suitable to drive R, L and C loads
  • Delayed cutoff for quick charging of capacitive loads
  • Able to handle up to 500 mJ inductive loads
  • Full reverse polarity protection on VCC , GND, OUTH, OUTL and I/Q pins
  • Green device status LED (ON or OFF)
  • Red diagnostic LEDs for:
    • cutoff and overtemperature events
    • overload
  • Supports COM1, COM2 and COM3
  • Meets IEC 61000-4-4 (burst), IEC 61000-4-2 (ESD) and EN60947-5-2/IEC 61000-4-5 (surge) requirements
  • RoHS compliant

Show More

STEVAL-IFP016V2 IO-Link communication master transceiver demonstration board based on the L6360 Quick view

主要特性

  • Supply voltage from 18 V to 32.5 V
  • Fully protected programmable output stages
  • Supports COM1, COM2 and COM3 mode
  • 5 mA IO-Link digital input
  • Additional IEC61131-2 type-1 input
  • 3.3 V / 5 V, 50 mA linear regulator
  • Fast mode I2 C for IC control, configuration and diagnostic
  • Diagnostic dual LED sequence generator and driver
  • 5 V and 3.3 V compatible I/Os
  • Interface compatible with STEVAL-PCC009V2 and STEVAL-PCC009V1
  • EMC immune application against ESD, burst, surge, RF noise, etc., according to IEC61000-4-2, IEC61000-4-4, IEC61000-4-5, and IEC61000-4-6 standards
  • RoHS compliant

Show More

STEVAL-PCC009V2 IBU Motor Control & IPS universal interface Quick view

主要特性

  • Supports two modes:
    • application mode: the PC GUI allows SPI, I2 C and UART interfacing and control of the communication parameters
    • DFU mode: allows the user to change the firmware if required to suit specific applications
  • Board power supplied through a USB Mini B-type connector
  • DLL files provided to allow users to create a customized PC GUI
  • RoHS compliant

Show More

STEVAL-IOD003V1 IO-Link (PHY) device evaluation board based on L6362A with Arduino connectors for STM32 Nucleo Quick view

主要特性

  • L6362A IO-Link device transceiver main characteristics:
    • IO-Link PHY layer
    • Dedicated overload diagnostics pin
    • UART interface
    • Selectable 12 mA 3.3 V or 10 mA 5.0 V linear regulator
    • Overload and overheating protections with non-dissipative cut-off function
    • Full reverse polarity on IO-Link interface pins
    • EMC protections (as per IO-Link v1.1)
    • Surge protection (as per IEC 60947-5-2)
    • DFN-12L (3x3x0.9 mm) package
  • 6.5 to 35 V operating voltage range
  • On-board 100 mA 12 V linear regulator (L78L)
  • LEDs for status and diagnostics
  • Ground and VCC wire break protections
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • RoHS and China RoHS compliant

Show More

STEVAL-IOM001V1 IO-Link master evaluation board based on L6360 equipped with ST morpho connectors for STM32 Nucleo Quick view

主要特性

  • IO-Link master PHY based on L6360
  • Interrupt diagnostics pin
  • I²C and UART interface
  • SPI (slave) interface
  • 65 mA selectable (3.3 or 5.0 V) linear regulator
  • CQ (push-pull) and L+ (high side) switches
  • IQ additional IEC61131-2 type 1 digital input
  • L+ and CQ overload and overheating protections with non-dissipative cut-off function
  • QFN-26L (3.5x5x1 mm) package
  • Operating voltage range from 18 to 32.5 V
  • Additional high side switch for L+ heavy loads (IPS161H)
  • LEDs for status and diagnostics
  • Ground and VCC wire break protections
  • EMC compliance with IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
  • Equipped with ST morpho connectors
  • CE certified
  • RoHS and China RoHS compliant

Show More

产品型号
P-NUCLEO-IOM01M1

STM32 Nucleo pack for IO-Link master with IO-Link v1.1 PHY and stack

主要特性

  • STEVAL-IOM001V1
    • IO-Link master PHY based on L6360
    • Interrupt diagnostics pin
    • I²C and UART interface
    • SPI (slave) interface
    • 65 mA selectable (3.3 or 5.0 V) linear regulator
    • CQ (push-pull) and L+ (high side) switches
    • IQ additional IEC61131-2 type 1 digital input
    • L+ and CQ overload and overheating protections with non-dissipative cut-off function
    • QFN-26L (3.5x5x1 mm) package
    • Operating voltage range from 18 to 32.5 V
    • Additional high side switch for L+ heavy loads (IPS161H)
    • LEDs for status and diagnostics
    • Ground and VCC wire break protections
    • EMC compliance with IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
    • Equipped with ST morpho connectors
    • CE certified
    • RoHS and China RoHS compliant
  • NUCLEO-F446RE
    • STM32F446RET6 32-bit Micro-controller based on ARM® Cortex® -M4 core (180 MHz max.) with 512-Kbyte Flash memory and 128 (+4) Kbyte RAM
    • Two types of extension resources: Arduino™ UNO Revision 3 connectivity and ST morpho extension pin headers for full access to all STM32 I/Os
    • Mbed-enabled (http://mbed.org)
    • On-board ST-LINK/V2-1 debugger/programmer with SWD connector: selection-mode switch to use the kit as a standalone ST-LINK/V2-1
    • Two push-buttons: USER and RESET

Show More

P-NUCLEO-IOD01A1

STM32 Nucleo pack for IO-Link device fully compatible with IO-Link v1.1 (PHY and stack)

主要特性

  • Equipped with Arduino UNO R3 connectors and compatible with STEVAL-IOD003V1, X-NUCLEO-IKS01A2 and NUCLEO-L073RZ boards.
  • The STEVAL-IOD003V1 features:
    • IO-Link (PHY) device layer based on L6362A
    • Operating voltage range 6.5 to 35 V
    • Dedicated CQ overload pin (wake-up)
    • Diagnostics pin (UVLO, overtemperature and cut-off)
    • UART interface
    • Linear regulators for independent supply from +24 V bus (12 mA 3.3 V and 100 mA 12 V)
    • LEDs for status and diagnostics
    • Overload and overheating protections with non-dissipative cut-off function
    • Full reverse polarity on IO-Link interface pins
    • EMC protections according to IO-Link v1.1 and IEC 60947-5-2
    • Ground and VCC wire break protections
  • The X-NUCLEO-IKS01A2 features:
    • LSM6DSL 3D accelerometer and 3D gyroscope
    • LSM303AGR 3D accelerometer and 3D magnetometer
    • LPS22HB pressure sensor
    • HTS221 capacitive digital relative humidity and temperature
    • DIL24 socket for additional MEMS adapters and other sensors
    • Free comprehensive development firmware library and samples for all sensors compatible with STM32Cube firmware
  • The NUCLEO-L073RZ features:
    • STM32L073RZT6 32-bit microcontroller based on ARM® Cortex® -M0+ core
    • Pre-programmed IO-Link device stack (v1.1 compatible)
    • Arduino UNO R3 connectivity and ST morpho extension pin headers
    • Mbed-enabled (http://mbed.org)
    • On-board ST-LINK/V2-1 debugger/programmer with SWD connector

Show More

STEVAL-IDP004V1

IO-Link master multi-port evaluation board based on L6360

主要特性

  • Main supply voltage 32 V maximum
  • 4 L6360 IO-Link master devices
  • RS-485 serial interface
  • CAN serial interface
  • USB interface
  • DC-DC converter
  • On-board reverse polarity protection
  • Designed to meet IEC requirement for industrial standards
  • RoHS and WEEE compliant

Show More

STEVAL-IDP003V1

IO-Link industrial modular sensor board based on L6362A

主要特性

  • Main supply voltage: 32 V maximum
  • STM32L071CZ microcontroller
  • IO-Link PHY using the L6362A device for data communication with host unit
  • DC-DC converter and linear regulator on board
  • Integrated reverse polarity protection on L6362A ICs
  • Multi-sensor connection
  • 400 kHz I²C communication
  • PCB designed to accept real industrial sensors (8 mm x 70 mm, with 0.8 mm thickness)
  • Designed to meet IEC industrial standard requirements
  • RoHS compliant

Show More

STEVAL-IFP017V3

Evaluation board for IO-Link transceiver device L6362A

主要特性

  • Operating voltage from 7 to 36 V
  • Operating current up to 300 mA
  • Configurable in push-pull, high-side or low-side
  • Overcurrent protection with cutoff function
  • Overtemperature protection
  • Suitable to drive R, L and C loads
  • Delayed cutoff for quick charging of capacitive loads
  • Able to handle up to 500 mJ inductive loads
  • Full reverse polarity protection on VCC , GND, OUTH, OUTL and I/Q pins
  • Green device status LED (ON or OFF)
  • Red diagnostic LEDs for:
    • cutoff and overtemperature events
    • overload
  • Supports COM1, COM2 and COM3
  • Meets IEC 61000-4-4 (burst), IEC 61000-4-2 (ESD) and EN60947-5-2/IEC 61000-4-5 (surge) requirements
  • RoHS compliant

Show More

STEVAL-IFP016V2

IO-Link communication master transceiver demonstration board based on the L6360

主要特性

  • Supply voltage from 18 V to 32.5 V
  • Fully protected programmable output stages
  • Supports COM1, COM2 and COM3 mode
  • 5 mA IO-Link digital input
  • Additional IEC61131-2 type-1 input
  • 3.3 V / 5 V, 50 mA linear regulator
  • Fast mode I2 C for IC control, configuration and diagnostic
  • Diagnostic dual LED sequence generator and driver
  • 5 V and 3.3 V compatible I/Os
  • Interface compatible with STEVAL-PCC009V2 and STEVAL-PCC009V1
  • EMC immune application against ESD, burst, surge, RF noise, etc., according to IEC61000-4-2, IEC61000-4-4, IEC61000-4-5, and IEC61000-4-6 standards
  • RoHS compliant

Show More

STEVAL-PCC009V2

IBU Motor Control & IPS universal interface

主要特性

  • Supports two modes:
    • application mode: the PC GUI allows SPI, I2 C and UART interfacing and control of the communication parameters
    • DFU mode: allows the user to change the firmware if required to suit specific applications
  • Board power supplied through a USB Mini B-type connector
  • DLL files provided to allow users to create a customized PC GUI
  • RoHS compliant

Show More

STEVAL-IOD003V1

IO-Link (PHY) device evaluation board based on L6362A with Arduino connectors for STM32 Nucleo

主要特性

  • L6362A IO-Link device transceiver main characteristics:
    • IO-Link PHY layer
    • Dedicated overload diagnostics pin
    • UART interface
    • Selectable 12 mA 3.3 V or 10 mA 5.0 V linear regulator
    • Overload and overheating protections with non-dissipative cut-off function
    • Full reverse polarity on IO-Link interface pins
    • EMC protections (as per IO-Link v1.1)
    • Surge protection (as per IEC 60947-5-2)
    • DFN-12L (3x3x0.9 mm) package
  • 6.5 to 35 V operating voltage range
  • On-board 100 mA 12 V linear regulator (L78L)
  • LEDs for status and diagnostics
  • Ground and VCC wire break protections
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • RoHS and China RoHS compliant

Show More

STEVAL-IOM001V1

IO-Link master evaluation board based on L6360 equipped with ST morpho connectors for STM32 Nucleo

主要特性

  • IO-Link master PHY based on L6360
  • Interrupt diagnostics pin
  • I²C and UART interface
  • SPI (slave) interface
  • 65 mA selectable (3.3 or 5.0 V) linear regulator
  • CQ (push-pull) and L+ (high side) switches
  • IQ additional IEC61131-2 type 1 digital input
  • L+ and CQ overload and overheating protections with non-dissipative cut-off function
  • QFN-26L (3.5x5x1 mm) package
  • Operating voltage range from 18 to 32.5 V
  • Additional high side switch for L+ heavy loads (IPS161H)
  • LEDs for status and diagnostics
  • Ground and VCC wire break protections
  • EMC compliance with IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
  • Equipped with ST morpho connectors
  • CE certified
  • RoHS and China RoHS compliant

Show More

00 选择要下载的文档

技术文档

    • 描述 版本 文档大小 操作
      AN5041
      IO-Link evaluation kit using STEVAL-IDP004V1 master evaluation board and STEVAL-IDP003V1 kit
      3.0
      1.96 MB
      PDF
      AN4113
      Managing the Driver Enable signal for RS-485 and IO-Link communications with the STM32F05x USART
      1.3
      142.25 KB
      PDF
      AN3070
      管理驱动器使能信号以使用STM32™的 USART 进行 RS-485 和 IO-Link 通信
      1.4
      467.28 KB
      PDF
      AN4828
      STEVAL-IFP017V3 evaluation board based on the L6362A transceiver for IO-Link and SIO mode communication
      1.0
      992.21 KB
      PDF
      AN5041

      IO-Link evaluation kit using STEVAL-IDP004V1 master evaluation board and STEVAL-IDP003V1 kit

      AN4113

      Managing the Driver Enable signal for RS-485 and IO-Link communications with the STM32F05x USART

      AN3070

      管理驱动器使能信号以使用STM32™的 USART 进行 RS-485 和 IO-Link 通信

      AN4828

      STEVAL-IFP017V3 evaluation board based on the L6362A transceiver for IO-Link and SIO mode communication

    • 描述 版本 文档大小 操作
      UM2421
      Getting started with the P-NUCLEO-IOM01M1 full IO-Link master (PHY plus stack) evaluation board and development system
      3.0
      981.99 KB
      PDF
      UM2421

      Getting started with the P-NUCLEO-IOM01M1 full IO-Link master (PHY plus stack) evaluation board and development system

演示和培训资料

    • 描述 版本 文档大小 操作
      L6360 and L6362A: A smart way to drive industrial sensors and actuators 1.0
      906.99 KB
      PDF
      STM32 and STM8 embedded software solutions 7.0
      3.12 MB
      PDF

      L6360 and L6362A: A smart way to drive industrial sensors and actuators

      STM32 and STM8 embedded software solutions

出版刊物和宣传资料

    • 描述 版本 文档大小 操作
      L6360 and L6362A - Embracing the Industry 4.0 revolution 12.2018
      282.88 KB
      PDF

      L6360 and L6362A - Embracing the Industry 4.0 revolution

    • 描述 版本 文档大小 操作
      Intelligent power switches (IPS) 04.2018
      4.21 MB
      PDF
      Products and solutions for Smart industry 3.0
      3.32 MB
      PDF

      Intelligent power switches (IPS)

      Products and solutions for Smart industry

设计工具

    • 产品型号

      Transient voltage suppressor smart selection tool

开发工具硬件

    • 产品型号

      Protection product finder application for Android and iOS

软件

    • 产品型号

      GUI setup for STEVAL-IDI00xV2 boards

      STSW-IFP016V2 application software setup

      IO-Link demonstration kit firmware

      L6362A IO-Link communication transceiver device IC evaluation software based on STM32Cube

      IO-Link device description software for P-NUCLEO-IOD01A1

      L6360 IO-Link communication transceiver master IC evaluation software based on STM32Cube

    • 产品型号

      Managing the Driver Enable signal for RS-485 and IO-Link communications with the STM32 USART

      Managing the driver enable signal for RS-485 and IO-Link communications with the STM32F05x USART (AN4113)

电源管理

产品型号 描述
L6360 IO-Link communication master transceiver IC
L6362A IO-Link communication transceiver device IC
产品型号
IO-Link communication master transceiver IC
IO-Link communication transceiver device IC

Protection Devices

产品型号 描述
CLT01-38SQ7 High speed digital input current limiter
产品型号
High speed digital input current limiter