USB-IF certified solutions for USB type-C and Power Delivery

搜索历史

Please log in to show your saved searches.

概述

解决方案

硬件评估工具

资源

工具和软件

主要产品

开始

快速链接

STM32F0

USB Type -C Interface

Authentication Secure Solution

Load Swtich-30 V P-channel STripFET

USB Type-C protection

产品型号	描述
STEVAL-STWINWFV1	Wi-Fi expansion for the SensorTile Wireless Industrial Node (STWIN) kit	Quick view 主要特性 Wi-Fi adapter for STWIN (STEVAL-STWINKT1) Plugs into STWIN core system board through dedicated 12-pin connector Single 3.3 V power supply input ISM43362-M3G-L44-E Wi-Fi module: 802.11 b/g/n Compatible based on Broadcom MAC/Baseband/Radio device Fully contained TCP/IP stack Host interface: SPI up to 25 MHz Network features ICMP ( Ping), ARP, DHCP,TCP, UDP Low power operation (3.3 V supply) with built-in low power modes Secure Wi-Fi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK CE certified FCC certified IC certified RoHS and China RoHS compliant WEEE compliant Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
EVAL-SCS001V1	Fast and easy migration from DC barrel to Type-C	Quick view 主要特性 USB Power Delivery SINK port Short-to VBUS protection up to 28 V Low BOM cost, small footprint Status LED Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
NUCLEO-L552ZE-Q	STM32 Nucleo-144 development board with STM32L552ZE MCU, SMPS, supports Arduino, ST Zio and morpho connectivity	Quick view 主要特性 Common features STM32 microcontroller in LQFP144 package 3 user LEDs 2 user and reset push-buttons 32.768 kHz crystal oscillator Board connectors:SWDST Zio expansion connector including Arduino™ Uno V3ST morpho expansion connector Flexible power-supply options: ST-LINK, USB V_BUS or external sources On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port Comprehensive free software libraries and examples available with the STM32Cube MCU Package Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs Board-specific features External or internal SMPS to generate V_core logic supply Ethernet compliant with IEEE-802.3-2002 USB OTG full speed or device only Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45 Arm^® Mbed Enabled™ compliant Show More Product Details 下载产品简介图片
STEVAL-STRKT01	LoRa® IoT tracker	Quick view 主要特性 Optimized IoT tracker solution over LoRaWAN™ network with simultaneous multi-constellation GNSS positioning and geofencing support Battery operated solution with smart power management architecture First IoT ST reference embedding a USB Type-C connector and a port controller Environmental and motion sensors Data logging STM32Cube function pack (FP-ATR-LORA1) High flexibility to cover different application profiles: asset tracker people and animal tracker fleet management WEEE and RoHS compliant 2006/66/EC Directive compliant Contains trasmitter module FCC ID: VPYCMABZ and IC ID: 772C-CMABZ CE certified Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STM32G484E-EVAL	Evaluation board with STM32G484QE MCU	Quick view 主要特性 Common features 240x320 TFT color LCD display module with SPI interface 16-Gbyte microSD™ card bundled On-board current measurement SAI audio codec Temperature sensor 8-Mbit (512 K x 16-bit) SRAM Two 512-Mbit Quad-SPI NOR Flash memories Four color user LEDs One high brightness LED Reset and wake-up / tamper buttons 4-direction joystick with selection button Light-dependent resistor (LDR) Potentiometer Access to comparator and operational amplifier Board connectors:Analog line input jackStereo headset jackTwo connectors for external speakersmicroSD™ cardEXT_I2C connector supporting I²C busRS-232 port configurable for communication or MCU flashingRS-485 portUSB Type-C™ port supporting USB FS DeviceTwo CAN 2.0A/B-compliant portsConnector for DAC outputJTAG/SWD connectorETM trace debug connectorUser interface through USB virtual COM portEmbedded STLINK-V3E debug and flashing facilityTAG connector 10-pin footprintArm^® Cortex^® 10-pin 1.27 mm-pitch debug connector over STDC14 footprintCoin cell battery holder Board expansion connectors:Two sets of motor control expansion connectorsBoard expansion extension connectors Flexible power-supply options:ST-LINK USB V_BUS , external sources, USB Type-C™ connector, or daughterboard On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port Microcontroller supply voltage: fixed 3.3 V or adjustable range from 1.62 V to 3.6 V Comprehensive free software libraries and examples available with the STM32CubeG4 MCU Package Support of a wide choice of integrated development environments (IDEs) including IAR™, Keil^® , GCC-based IDEs Board-specific features STM32G474QET6U microcontroller with 512 Kbytes of Flash memory and 96 Kbytes of RAM in LQFP128 package (STM32G474E-EVAL and STM32G474E-EVAL1) STM32G474E-EVAL1 is the board to use for motor control application with solder bridge and resistor configuration STM32G484QET6U with cryptography (STM32G484E-EVAL) Fully compatible with all microcontrollers of the STM32G4x1 and STM32G4x3 lines with "QET6" part number suffix Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STM32G474E-EVAL	Evaluation board with STM32G474QE MCU	Quick view 主要特性 Common features 240x320 TFT color LCD display module with SPI interface 16-Gbyte microSD™ card bundled On-board current measurement SAI audio codec Temperature sensor 8-Mbit (512 K x 16-bit) SRAM Two 512-Mbit Quad-SPI NOR Flash memories Four color user LEDs One high brightness LED Reset and wake-up / tamper buttons 4-direction joystick with selection button Light-dependent resistor (LDR) Potentiometer Access to comparator and operational amplifier Board connectors:Analog line input jackStereo headset jackTwo connectors for external speakersmicroSD™ cardEXT_I2C connector supporting I²C busRS-232 port configurable for communication or MCU flashingRS-485 portUSB Type-C™ port supporting USB FS DeviceTwo CAN 2.0A/B-compliant portsConnector for DAC outputJTAG/SWD connectorETM trace debug connectorUser interface through USB virtual COM portEmbedded STLINK-V3E debug and flashing facilityTAG connector 10-pin footprintArm^® Cortex^® 10-pin 1.27 mm-pitch debug connector over STDC14 footprintCoin cell battery holder Board expansion connectors:Two sets of motor control expansion connectorsBoard expansion extension connectors Flexible power-supply options:ST-LINK USB V_BUS , external sources, USB Type-C™ connector, or daughterboard On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port Microcontroller supply voltage: fixed 3.3 V or adjustable range from 1.62 V to 3.6 V Comprehensive free software libraries and examples available with the STM32CubeG4 MCU Package Support of a wide choice of integrated development environments (IDEs) including IAR™, Keil^® , GCC-based IDEs Board-specific features STM32G474QET6U microcontroller with 512 Kbytes of Flash memory and 96 Kbytes of RAM in LQFP128 package (STM32G474E-EVAL and STM32G474E-EVAL1) STM32G474E-EVAL1 is the board to use for motor control application with solder bridge and resistor configuration STM32G484QET6U with cryptography (STM32G484E-EVAL) Fully compatible with all microcontrollers of the STM32G4x1 and STM32G4x3 lines with "QET6" part number suffix Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STEVAL-ISB047V1	Qi certified 3-coil 15 W wireless charger TX evaluation kit based on STWBC-MC	Quick view 主要特性 STWBC-MC digital controller MP-A15 3-coil array 15 W potential power Flexible input voltage: 5 to 20 V from USB-C or DC jack 5 W mode when connected to 5 V USB input or DC jack Fixed frequency operation WPC Qi1.2.4 standard certified Robust demodulation algorithm, with triple path (V, I, f) Foreign object detection (FOD) Active presence detection UART protocol to control and monitor the system Complete reference design (evaluation board, schematics, PCB layout, firmware and tools) 2-layer PCB Low standby power consumption Flash memory based CE certified RoHS compliant WEEE compliant Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STEVAL-USBC2DP	USB Type-C™ to DisplayPort™ adapter	Quick view 主要特性 Full reference design for USB Type-C to DisplayPort adapter with USB Type-C connector and DisplayPort connector. Single chip solution based on the STM32F072 series 32-bit microcontrollers with integrated USB 2.0 peripheral. Based on certified X-CUBE-USB-PD middleware stack, compliant with the following standards and specifications: USB Type-C Cable and Connector 1.3 USB Power Delivery 2.0 and 3.0 VESA DisplayPort Alternate Mode on USB Type-C Standard 1.0a USB Device Class Definition for Billboard Devices 1.21 EMI filtering and ESD protection circuits. Compact PCB design: 5.5 x 2.3 cm RoHS compliant Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STM32G071B-DISCO	Discovery kit with STM32G071RB MCU	Quick view 主要特性 STM32G071RBT6 microcontroller featuring 128 Kbytes of Flash memory and 32 Kbytes of RAM in LQFP64 package Plastic case 1” 128 x 64 pixels OLED LCD module with SPI interface USB Type-C™ interface plug cable and receptacle connector accessible by door with reed sensor detection 3 bidirectional current and power monitors with I² C interface to measure V_BUS , CC1 and CC2 protected and isolated lines On-board DC/DC converter to sustain power supply with V_BUS varying from 3 V to 20 V (+/- 5 %) 4 user status LEDs about USB Type-C™ configuration 3 LEDs for power and ST-LINK communication 4-way joystick with selection button 1 reset push-button Board external connectors: USB Type-C™ plug cable USB Type-C™ receptacle connector 8-pin user extension connector including ADC, SPI, USART and I² C communication signals USB with Micro-AB (ST-LINK) Board internal connectors: 2 x 8-pin GPIOs free pins from microcontroller (accessible internally when case is removed) USB Type-C™ test points for main signals Flexible power-supply options: ST-LINK USB V_BUS or USB Type-C™ V_BUS On-board ST-LINK/V2-1 debugger/programmer with USB enumeration capability: mass storage, Virtual COM port and debug port Comprehensive free software libraries and examples available with the STM32Cube™ MCU Package Support of a wide choice of integrated development environments (IDEs), including IAR™, Keil^® and GCC-based IDEs Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STM32G081B-EVAL	Evaluation board with STM32G081RB MCU	Quick view 主要特性 Mother board STM32G081RBT6 microcontroller with 128 Kbytes of Flash memory and 32 Kbytes of RAM in LQFP64 package MCU voltage choice fixed 3.3 V or adjustable from 1.65 V to 3.6 V I² C compatible serial interface RTC with backup battery 8-Gbyte or more SPI interface microSD card Potentiometer 4 color user LEDs and one LED as MCU low-power alarm Reset, Tamper and User buttons 4-direction control and selection joystick Board connectors: 5 V power jack RS-232 and RS485 communications Stereo audio jack including analog microphone input microSD card Extension I²C connector Motor-control connector Board extension connectors: Daughterboard connectors for legacy peripheral daughter board or USB-C daughterboard Extension connectors for daughterboard or wire-wrap board Flexible power-supply options: 5 V power jack ST-LINK/V2-1 USB connector Daughterboard On-board ST-LINK/V2-1 debugger/programmer with USB re- enumeration capability: mass storage, virtual COM port and debug port Comprehensive free software libraries and examples available with the STM32Cube package Support of a wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs Legacy peripheral daughterboard IrDA transceiver IR LED and IR receiver Light dependent resistor (LDR) Temperature Sensor Board connectors: Two HDMI connectors with DDC and CEC Smart card slot USB-C and Power Delivery daughterboard Mux for USB3.1 Gen1 / DisplayPort input and Type-C port1 output Mux for Type-C port2 input and DisplayPort output / USB2.0 VCONN on Type-C port1 USB PD on Type-C port1 Board connectors: Type-C port1 DRP (dual-role port) Type-C port2 Sink DisplayPort input DisplayPort output USB 3.1 Gen1 Type-B receptacle USB2.0 Type-A receptacle 19 V power jack for USB PD Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STEVAL-USBPD45C	45 W USB Type-C™ Power Delivery adapter reference design based on STCH03, STM32F051 and STUSB1602A	Quick view 主要特性 USB PD 3.0 compliant Universal input mains voltage range: from 90 V_AC to 264 V_AC (frequency from 45 Hz to 65 Hz) Three fixed PDOs available: 5 V, 9 V, 15 V – 3 A continuous operation Load power limited to 45 W Minimum four-point average efficiency in active mode compliant with CoC ver. 5 – Tier 2 and DOE requirement Efficiency > 50% with Pout = 250 mW < 35 mW no-load standby power Adaptive synchronous rectification with digital driver and controller Load feedforward OVP, UVP, OC, short-circuit protections ESD protection: > 30 kV contact on VBUS and 20 kV contact on CC lines and according to IEC61000-4-2 Immunity against surge current on VBUS pin up to 35 A in a 8/20 µs waveform, according to IEC61000-4-5 Compact design: 73x51x25 mm RoHS compliant Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STEVAL-ISC005V1	Evaluation board for the STUSB4500 USB Power Delivery controller	Quick view 主要特性 USB PD port (sink) STUSB4500 USB Power Delivery controller, certified for: USB type-C™ (rev1.2) USB PD (rev2.0) TID: 1000133 Compliant with USB PD (rev3.0) 5 V on-board DC-DC V_BUS power switches and discharge path Support to up to 3 power data objects (PDO) Short-to-V_BUS protections on CC pins (22 V) and V_BUS pins (28 V) Customizable start-up profiles Multiple output paths Compatible with NUCLEO-F072RB development board for configuration and debug interface CE certified RoHS and China RoHS compliant Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STEVAL-ISC004V1	STUSB4710A evaluation board (with on-board DC-DC)	Quick view 主要特性 1 x USB PD port (source) STUSB4710A USB power delivery controller Compliant with: USB Type-C r1.2 USB PD r2.0 On-board DC-DC V_BUS power switches and discharge path Support for up to 5 power data objects (PDO) Short-to-V_BUS protections on CC pins (22 V) and V_BUS pins (28 V) Customizable start-up profiles Compatible with NUCLEO-F072RB board for configuration and debug interface RoHS compliant Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STEVAL-CCC002V1	STUSB1600A Type-C™ controller evaluation board	Quick view 主要特性 1 full-featured USB Type-C port (Source/Sink/Dual-role) STUSB1600A Type-C controller compliant with USB Type-C standard rel. 1.2 + ECR V_BUS power switches and discharge path V_CONN support (programmable current limit up to 600 mA) Dead Battery mode support Compatible with NUCLEO-F072RB board for configuration and debug interface Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STEVAL-USBPD45H	USB Power Delivery (Type-C PD) 45 W USB wall power adapter solution based on STCH02 and STUSB4700	Quick view 主要特性 USB wall power adapter input: 85 V_AC to 264 V_AC USB voltage output: 5 V, 9 V and 15 V Current limit: 3 A for all voltage level profiles Load power limited to 45 W Cable compensation Isolated quasi-resonant flyback Efficiency 90% (approx.) USB Type-C Power Delivery compatible USB-IF certified Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
STEVAL-OET004V1	USB Type-C protection and filtering demo PCB	Quick view 主要特性 Protection of all lines (data, control and power) Common mode filters for USB 2.0 and USB 3.1 lines on STEVAL-OET004V1D Plug and receptacle enabling insertion of the PCB between host and cable or device and cable Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber
P-NUCLEO-USB002	STUSB1602 USB Type-C and Power Delivery Nucleo Pack with NUCLEO-F072RB	Quick view 主要特性 32-bit ARM^® Cortex^® -M0-based microcontroller STM32F072RB with 128 kB Flash and 16 kB SRAM Dual port solution based on certified USB Type-C™ port controller STUSB1602, featuring: Type-C FSM with attach/detach and cable orientation detection USB PD PHY and BMC transceiver High voltage (20 V) technology V_BUS voltage monitoring 600 mA V_CONN power switch V_BUS and V_CONN discharge paths Dead-battery support 22 V CC line protection V_BUS switch gate drivers Power connector to interface with external power supply (not included) USB 2.0 full speed data communication interface RoHS compliant Show More Product Details 下载产品简介图片特色资源 Schematics BOM Gerber

产品型号

STEVAL-STWINWFV1

Wi-Fi expansion for the SensorTile Wireless Industrial Node (STWIN) kit

快速查看

主要特性

Wi-Fi adapter for STWIN (STEVAL-STWINKT1)
Plugs into STWIN core system board through dedicated 12-pin connector
Single 3.3 V power supply input
ISM43362-M3G-L44-E Wi-Fi module:
- 802.11 b/g/n Compatible based on Broadcom MAC/Baseband/Radio device
- Fully contained TCP/IP stack
- Host interface: SPI up to 25 MHz
- Network features ICMP ( Ping), ARP, DHCP,TCP, UDP
- Low power operation (3.3 V supply) with built-in low power modes
- Secure Wi-Fi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK
- CE certified
- FCC certified
- IC certified
RoHS and China RoHS compliant
WEEE compliant

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

EVAL-SCS001V1

Fast and easy migration from DC barrel to Type-C

快速查看

NUCLEO-L552ZE-Q

STM32 Nucleo-144 development board with STM32L552ZE MCU, SMPS, supports Arduino, ST Zio and morpho connectivity

快速查看

主要特性

Common features
- STM32 microcontroller in LQFP144 package
- 3 user LEDs
- 2 user and reset push-buttons
- 32.768 kHz crystal oscillator
- Board connectors:SWDST Zio expansion connector including Arduino™ Uno V3ST morpho expansion connector
- Flexible power-supply options: ST-LINK, USB V_BUS or external sources
- On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
- Comprehensive free software libraries and examples available with the STM32Cube MCU Package
- Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
Board-specific features
- External or internal SMPS to generate V_core logic supply
- Ethernet compliant with IEEE-802.3-2002
- USB OTG full speed or device only
- Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45
- Arm^® Mbed Enabled™ compliant

Product Details 下载产品简介

图片

STEVAL-STRKT01

LoRa® IoT tracker

快速查看

主要特性

Optimized IoT tracker solution over LoRaWAN™ network with simultaneous multi-constellation GNSS positioning and geofencing support
Battery operated solution with smart power management architecture
First IoT ST reference embedding a USB Type-C connector and a port controller
Environmental and motion sensors
Data logging
STM32Cube function pack (FP-ATR-LORA1)
High flexibility to cover different application profiles:
- asset tracker
- people and animal tracker
- fleet management
WEEE and RoHS compliant
2006/66/EC Directive compliant
Contains trasmitter module FCC ID: VPYCMABZ and IC ID: 772C-CMABZ
CE certified

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STM32G484E-EVAL

Evaluation board with STM32G484QE MCU

快速查看

主要特性

Common features
- 240x320 TFT color LCD display module with SPI interface
- 16-Gbyte microSD™ card bundled
- On-board current measurement
- SAI audio codec
- Temperature sensor
- 8-Mbit (512 K x 16-bit) SRAM
- Two 512-Mbit Quad-SPI NOR Flash memories
- Four color user LEDs
- One high brightness LED
- Reset and wake-up / tamper buttons
- 4-direction joystick with selection button
- Light-dependent resistor (LDR)
- Potentiometer
- Access to comparator and operational amplifier
- Board connectors:Analog line input jackStereo headset jackTwo connectors for external speakersmicroSD™ cardEXT_I2C connector supporting I²C busRS-232 port configurable for communication or MCU flashingRS-485 portUSB Type-C™ port supporting USB FS DeviceTwo CAN 2.0A/B-compliant portsConnector for DAC outputJTAG/SWD connectorETM trace debug connectorUser interface through USB virtual COM portEmbedded STLINK-V3E debug and flashing facilityTAG connector 10-pin footprintArm^® Cortex^® 10-pin 1.27 mm-pitch debug connector over STDC14 footprintCoin cell battery holder
- Board expansion connectors:Two sets of motor control expansion connectorsBoard expansion extension connectors
- Flexible power-supply options:ST-LINK USB V_BUS , external sources, USB Type-C™ connector, or daughterboard
- On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
- Microcontroller supply voltage: fixed 3.3 V or adjustable range from 1.62 V to 3.6 V
- Comprehensive free software libraries and examples available with the STM32CubeG4 MCU Package
- Support of a wide choice of integrated development environments (IDEs) including IAR™, Keil^® , GCC-based IDEs
Board-specific features
- STM32G474QET6U microcontroller with 512 Kbytes of Flash memory and 96 Kbytes of RAM in LQFP128 package (STM32G474E-EVAL and STM32G474E-EVAL1)
- STM32G474E-EVAL1 is the board to use for motor control application with solder bridge and resistor configuration
- STM32G484QET6U with cryptography (STM32G484E-EVAL)
Fully compatible with all microcontrollers of the STM32G4x1 and STM32G4x3 lines with "QET6" part number suffix

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STM32G474E-EVAL

Evaluation board with STM32G474QE MCU

快速查看

主要特性

Common features
- 240x320 TFT color LCD display module with SPI interface
- 16-Gbyte microSD™ card bundled
- On-board current measurement
- SAI audio codec
- Temperature sensor
- 8-Mbit (512 K x 16-bit) SRAM
- Two 512-Mbit Quad-SPI NOR Flash memories
- Four color user LEDs
- One high brightness LED
- Reset and wake-up / tamper buttons
- 4-direction joystick with selection button
- Light-dependent resistor (LDR)
- Potentiometer
- Access to comparator and operational amplifier
- Board connectors:Analog line input jackStereo headset jackTwo connectors for external speakersmicroSD™ cardEXT_I2C connector supporting I²C busRS-232 port configurable for communication or MCU flashingRS-485 portUSB Type-C™ port supporting USB FS DeviceTwo CAN 2.0A/B-compliant portsConnector for DAC outputJTAG/SWD connectorETM trace debug connectorUser interface through USB virtual COM portEmbedded STLINK-V3E debug and flashing facilityTAG connector 10-pin footprintArm^® Cortex^® 10-pin 1.27 mm-pitch debug connector over STDC14 footprintCoin cell battery holder
- Board expansion connectors:Two sets of motor control expansion connectorsBoard expansion extension connectors
- Flexible power-supply options:ST-LINK USB V_BUS , external sources, USB Type-C™ connector, or daughterboard
- On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
- Microcontroller supply voltage: fixed 3.3 V or adjustable range from 1.62 V to 3.6 V
- Comprehensive free software libraries and examples available with the STM32CubeG4 MCU Package
- Support of a wide choice of integrated development environments (IDEs) including IAR™, Keil^® , GCC-based IDEs
Board-specific features
- STM32G474QET6U microcontroller with 512 Kbytes of Flash memory and 96 Kbytes of RAM in LQFP128 package (STM32G474E-EVAL and STM32G474E-EVAL1)
- STM32G474E-EVAL1 is the board to use for motor control application with solder bridge and resistor configuration
- STM32G484QET6U with cryptography (STM32G484E-EVAL)
Fully compatible with all microcontrollers of the STM32G4x1 and STM32G4x3 lines with "QET6" part number suffix

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STEVAL-ISB047V1

Qi certified 3-coil 15 W wireless charger TX evaluation kit based on STWBC-MC

快速查看

主要特性

STWBC-MC digital controller
MP-A15 3-coil array
15 W potential power
Flexible input voltage: 5 to 20 V from USB-C or DC jack
5 W mode when connected to 5 V USB input or DC jack
Fixed frequency operation
WPC Qi1.2.4 standard certified
Robust demodulation algorithm, with triple path (V, I, f)
Foreign object detection (FOD)
Active presence detection
UART protocol to control and monitor the system
Complete reference design (evaluation board, schematics, PCB layout, firmware and tools)
2-layer PCB
Low standby power consumption
Flash memory based
CE certified
RoHS compliant
WEEE compliant

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STEVAL-USBC2DP

USB Type-C™ to DisplayPort™ adapter

快速查看

主要特性

Full reference design for USB Type-C to DisplayPort adapter with USB Type-C connector and DisplayPort connector.
Single chip solution based on the STM32F072 series 32-bit microcontrollers with integrated USB 2.0 peripheral.
Based on certified X-CUBE-USB-PD middleware stack, compliant with the following standards and specifications:
- USB Type-C Cable and Connector 1.3
- USB Power Delivery 2.0 and 3.0
- VESA DisplayPort Alternate Mode on USB Type-C Standard 1.0a
- USB Device Class Definition for Billboard Devices 1.21
EMI filtering and ESD protection circuits.
Compact PCB design: 5.5 x 2.3 cm
RoHS compliant

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STM32G071B-DISCO

Discovery kit with STM32G071RB MCU

快速查看

主要特性

STM32G071RBT6 microcontroller featuring 128 Kbytes of Flash memory and 32 Kbytes of RAM in LQFP64 package
Plastic case
1” 128 x 64 pixels OLED LCD module with SPI interface
USB Type-C™ interface plug cable and receptacle connector accessible by door with reed sensor detection
3 bidirectional current and power monitors with I² C interface to measure V_BUS , CC1 and CC2 protected and isolated lines
On-board DC/DC converter to sustain power supply with V_BUS varying from 3 V to 20 V (+/- 5 %)
4 user status LEDs about USB Type-C™ configuration
3 LEDs for power and ST-LINK communication
4-way joystick with selection button
1 reset push-button
Board external connectors:
- USB Type-C™ plug cable
- USB Type-C™ receptacle connector
- 8-pin user extension connector including ADC, SPI, USART and I² C communication signals
- USB with Micro-AB (ST-LINK)
Board internal connectors:
- 2 x 8-pin GPIOs free pins from microcontroller (accessible internally when case is removed)
- USB Type-C™ test points for main signals
Flexible power-supply options: ST-LINK USB V_BUS or USB Type-C™ V_BUS
On-board ST-LINK/V2-1 debugger/programmer with USB enumeration capability: mass storage, Virtual COM port and debug port
Comprehensive free software libraries and examples available with the STM32Cube™ MCU Package
Support of a wide choice of integrated development environments (IDEs), including IAR™, Keil^® and GCC-based IDEs

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STM32G081B-EVAL

Evaluation board with STM32G081RB MCU

快速查看

主要特性

Mother board
- STM32G081RBT6 microcontroller with 128 Kbytes of Flash memory and 32 Kbytes of RAM in LQFP64 package
- MCU voltage choice fixed 3.3 V or adjustable from 1.65 V to 3.6 V
- I² C compatible serial interface
- RTC with backup battery
- 8-Gbyte or more SPI interface microSD card
- Potentiometer
- 4 color user LEDs and one LED as MCU low-power alarm
- Reset, Tamper and User buttons
- 4-direction control and selection joystick
- Board connectors:
  - 5 V power jack
  - RS-232 and RS485 communications
  - Stereo audio jack including analog microphone input
  - microSD card
  - Extension I²C connector
  - Motor-control connector
- Board extension connectors:
  - Daughterboard connectors for legacy peripheral daughter board or USB-C daughterboard
  - Extension connectors for daughterboard or wire-wrap board
- Flexible power-supply options:
  - 5 V power jack
  - ST-LINK/V2-1 USB connector
  - Daughterboard
- On-board ST-LINK/V2-1 debugger/programmer with USB re- enumeration capability: mass storage, virtual COM port and debug port
- Comprehensive free software libraries and examples available with the STM32Cube package
- Support of a wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs
Legacy peripheral daughterboard
- IrDA transceiver
- IR LED and IR receiver
- Light dependent resistor (LDR)
- Temperature Sensor
- Board connectors:
  - Two HDMI connectors with DDC and CEC
  - Smart card slot
USB-C and Power Delivery daughterboard
- Mux for USB3.1 Gen1 / DisplayPort input and Type-C port1 output
- Mux for Type-C port2 input and DisplayPort output / USB2.0
- VCONN on Type-C port1
- USB PD on Type-C port1
- Board connectors:
  - Type-C port1 DRP (dual-role port)
  - Type-C port2 Sink
  - DisplayPort input
  - DisplayPort output
  - USB 3.1 Gen1 Type-B receptacle
  - USB2.0 Type-A receptacle
  - 19 V power jack for USB PD

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STEVAL-USBPD45C

45 W USB Type-C™ Power Delivery adapter reference design based on STCH03, STM32F051 and STUSB1602A

快速查看

主要特性

USB PD 3.0 compliant
Universal input mains voltage range: from 90 V_AC to 264 V_AC (frequency from 45 Hz to 65 Hz)
Three fixed PDOs available: 5 V, 9 V, 15 V – 3 A continuous operation
Load power limited to 45 W
Minimum four-point average efficiency in active mode compliant with CoC ver. 5 – Tier 2 and DOE requirement
Efficiency > 50% with Pout = 250 mW
< 35 mW no-load standby power
Adaptive synchronous rectification with digital driver and controller
Load feedforward
OVP, UVP, OC, short-circuit protections
ESD protection: > 30 kV contact on VBUS and 20 kV contact on CC lines and according to IEC61000-4-2
Immunity against surge current on VBUS pin up to 35 A in a 8/20 µs waveform, according to IEC61000-4-5
Compact design: 73x51x25 mm
RoHS compliant

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STEVAL-ISC005V1

Evaluation board for the STUSB4500 USB Power Delivery controller

快速查看

主要特性

USB PD port (sink)
STUSB4500 USB Power Delivery controller, certified for:
- USB type-C™ (rev1.2)
- USB PD (rev2.0)
- TID: 1000133
Compliant with USB PD (rev3.0)
5 V on-board DC-DC
V_BUS power switches and discharge path
Support to up to 3 power data objects (PDO)
Short-to-V_BUS protections on CC pins (22 V) and V_BUS pins (28 V)
Customizable start-up profiles
Multiple output paths
Compatible with NUCLEO-F072RB development board for configuration and debug interface
CE certified
RoHS and China RoHS compliant

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STEVAL-ISC004V1

STUSB4710A evaluation board (with on-board DC-DC)

快速查看

主要特性

1 x USB PD port (source)
STUSB4710A USB power delivery controller
Compliant with:
- USB Type-C r1.2
- USB PD r2.0
On-board DC-DC
V_BUS power switches and discharge path
Support for up to 5 power data objects (PDO)
Short-to-V_BUS protections on CC pins (22 V) and V_BUS pins (28 V)
Customizable start-up profiles
Compatible with NUCLEO-F072RB board for configuration and debug interface
RoHS compliant

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STEVAL-CCC002V1

STUSB1600A Type-C™ controller evaluation board

快速查看

主要特性

1 full-featured USB Type-C port (Source/Sink/Dual-role)
STUSB1600A Type-C controller compliant with USB Type-C standard rel. 1.2 + ECR
V_BUS power switches and discharge path
V_CONN support (programmable current limit up to 600 mA)
Dead Battery mode support
Compatible with NUCLEO-F072RB board for configuration and debug interface

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STEVAL-USBPD45H

USB Power Delivery (Type-C PD) 45 W USB wall power adapter solution based on STCH02 and STUSB4700

快速查看

主要特性

USB wall power adapter input: 85 V_AC to 264 V_AC
USB voltage output: 5 V, 9 V and 15 V
Current limit: 3 A for all voltage level profiles
Load power limited to 45 W
Cable compensation
Isolated quasi-resonant flyback
Efficiency 90% (approx.)
USB Type-C Power Delivery compatible
USB-IF certified

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

STEVAL-OET004V1

USB Type-C protection and filtering demo PCB

快速查看

主要特性

Protection of all lines (data, control and power)
Common mode filters for USB 2.0 and USB 3.1 lines on STEVAL-OET004V1D
Plug and receptacle enabling insertion of the PCB between host and cable or device and cable

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

P-NUCLEO-USB002

STUSB1602 USB Type-C and Power Delivery Nucleo Pack with NUCLEO-F072RB

快速查看

主要特性

32-bit ARM^® Cortex^® -M0-based microcontroller STM32F072RB with 128 kB Flash and 16 kB SRAM
Dual port solution based on certified USB Type-C™ port controller STUSB1602, featuring:
- Type-C FSM with attach/detach and cable orientation detection
- USB PD PHY and BMC transceiver
- High voltage (20 V) technology
- V_BUS voltage monitoring
- 600 mA V_CONN power switch
- V_BUS and V_CONN discharge paths
- Dead-battery support
- 22 V CC line protection
- V_BUS switch gate drivers
Power connector to interface with external power supply (not included)
USB 2.0 full speed data communication interface
RoHS compliant

Product Details 下载产品简介

图片

特色资源

Schematics BOM Gerber

00 选择要下载的文档

技术文档

应用手册

描述	版本	文档大小	操作
AN576 PCB layout optimisation	3.0	109.53 KB	PDF
AN2484 STOTG04 in power down mode	1.2	669.19 KB	PDF
AN316 Transil™ clamping protection mode	4.3	432.1 KB	PDF
AN4871 USB Type-C protection and filtering	2.1	2.42 MB	PDF
AN5225 USB Type-C™ Power Delivery using STM32xx Series MCUs and STM32xxx Series MPUs	1.0	1.42 MB	PDF

AN576

PCB layout optimisation

PDF

AN2484

STOTG04 in power down mode

PDF

AN316

Transil™ clamping protection mode

PDF

AN4871

USB Type-C protection and filtering

PDF

AN5225

USB Type-C™ Power Delivery using STM32xx Series MCUs and STM32xxx Series MPUs

PDF

技术文档

	描述	版本	文档大小	操作
	TA0356 USB Type-C™ and Power Delivery DisplayPort Alternate Mode	1.0	6.03 MB	PDF

TA0356

USB Type-C™ and Power Delivery DisplayPort Alternate Mode

PDF

用户手册

	描述	版本	文档大小	操作
	UM2473 Managing the dynamic input power with the STUSB4500 and the STM32F072RB	2.0	1.08 MB	PDF

UM2473

Managing the dynamic input power with the STUSB4500 and the STM32F072RB

PDF

演示和培训资料

简报

描述	版本	文档大小	操作
STM32 and STM8 embedded software solutions	7.0	3.12 MB	PDF
STM32 solutions for USB-C™ & Power Delivery	1.1	843.01 KB	PDF
STM32G0 USB-C solutions marketing presentation	1.0	1.54 MB	PDF
USB type-C Power Delivery advanced protection fundamentals	1.0	396.47 KB	PDF
USB type-C™ advanced protection solutions quick start guide	2.0	1.31 MB	PDF
USB type-C™ datalines and 'alternate mode' advanced protection fundamentals	1.0	657.2 KB	PDF

STM32 and STM8 embedded software solutions

PDF

STM32 solutions for USB-C™ & Power Delivery

PDF

STM32G0 USB-C solutions marketing presentation

PDF

USB type-C Power Delivery advanced protection fundamentals

PDF

USB type-C™ advanced protection solutions quick start guide

PDF

USB type-C™ datalines and 'alternate mode' advanced protection fundamentals

PDF

出版刊物和宣传资料

宣传册

描述	版本	文档大小	操作
Power Delivery Protection - Simply cancel ESD and EOS events	1.0	519.6 KB	PDF
Power your device with USB PD!	1.0	1.18 MB	PDF
ST Protection Finder - The new app for Android and iOS	1.0	1.52 MB	PDF
Ultra-low clamping voltage 0201 ESD diodes	1.0	527.9 KB	PDF

Power Delivery Protection - Simply cancel ESD and EOS events

PDF

Power your device with USB PD!

PDF

ST Protection Finder - The new app for Android and iOS

PDF

Ultra-low clamping voltage 0201 ESD diodes

PDF

手册

	描述	版本	文档大小	操作
	Power Management Guide	06.2019	5.5 MB	PDF
	ST’s solutions for mobile devices	3.2	2.13 MB	PDF

Power Management Guide

PDF

ST’s solutions for mobile devices

PDF

设计工具

Smart selectors

Picture	产品型号	制造商	描述
	SEL-PROT-TVS	--	Transient voltage suppressor smart selection tool

产品型号

SEL-PROT-TVS

Transient voltage suppressor smart selection tool

开发工具硬件

软件开发工具

产品型号	制造商	描述
ST Protection Finder	ST	Protection product finder application for Android and iOS
STM32CubeMX	ST	STM32Cube initialization code generator
STM32CubeMonUCPD	ST	Monitoring and configuration software tool for STM32 USB-C and Power Delivery 3.0 applications

产品型号

ST Protection Finder

Protection product finder application for Android and iOS

STM32CubeMX

STM32Cube initialization code generator

STM32CubeMonUCPD

Monitoring and configuration software tool for STM32 USB-C and Power Delivery 3.0 applications

软件

评估工具软件

产品型号	制造商	描述
STSW-STUSB002	ST	Graphical User Interface for STUSB45
STSW-STUSB003	ST	Software Library for STUSB45
STSW-STUSB004	ST	NVM customization tool for STUSB45

产品型号

STSW-STUSB002

Graphical User Interface for STUSB45

STSW-STUSB003

Software Library for STUSB45

STSW-STUSB004

NVM customization tool for STUSB45

MCU 及 MPU嵌入式软件

产品型号	制造商	描述
STM32CubeG0	ST	STM32Cube MCU Package for STM32G0 series (HAL, Low-Layer APIs and CMSIS (CORE, DSP, RTOS), USB PD, File system, RTOS) - coming with examples running on ST boards: STM32 Nucleo, Discovery kits and Evaluation boards)
STM32CubeG4	ST	STM32Cube MCU Package for STM32G4 series (HAL, Low-Layer APIs and CMSIS (CORE, DSP, RTOS), USB, File system, RTOS, Graphic - coming with examples running on ST boards: STM32 Nucleo, Discovery kits and Evaluation boards)
STSW-STM32046	ST	STM32F105/7, STM32F2 and STM32F4 USB on-the-go Host and device library (UM1021)
STSW-STM32121	ST	STM32F10x, STM32L1xx and STM32F3xx USB full speed device library (UM0424)
X-CUBE-USB-PD	ST	USB Power Delivery on STM32 software expansion for STM32Cube (UM2063)

产品型号

STM32CubeG0

STM32Cube MCU Package for STM32G0 series (HAL, Low-Layer APIs and CMSIS (CORE, DSP, RTOS), USB PD, File system, RTOS) - coming with examples running on ST boards: STM32 Nucleo, Discovery kits and Evaluation boards)

STM32CubeG4

STM32Cube MCU Package for STM32G4 series (HAL, Low-Layer APIs and CMSIS (CORE, DSP, RTOS), USB, File system, RTOS, Graphic - coming with examples running on ST boards: STM32 Nucleo, Discovery kits and Evaluation boards)

STSW-STM32046

STM32F105/7, STM32F2 and STM32F4 USB on-the-go Host and device library (UM1021)

STSW-STM32121

STM32F10x, STM32L1xx and STM32F3xx USB full speed device library (UM0424)

X-CUBE-USB-PD

USB Power Delivery on STM32 software expansion for STM32Cube (UM2063)

评估工具

产品评估工具

Picture	产品型号	制造商	描述
	ON-FUSB3-STM32	ON Semiconductor	STM32F072 Type-C Port Manager evaluation board with FUSB307B Type-C Port Controller from ON Semiconductor

产品型号

ON-FUSB3-STM32

STM32F072 Type-C Port Manager evaluation board with FUSB307B Type-C Port Controller from ON Semiconductor

EMI Filtering and Signal Conditioning

产品型号	描述
ECMF02-2AMX6	Common-mode filter and ESD protection for USB 2.0 and MIPI/MDDI interfaces
ECMF04-4HSWM10	Common mode filter with ESD protection for High Speed Serial interfaces

产品型号

ECMF02-2AMX6

Common-mode filter and ESD protection for USB 2.0 and MIPI/MDDI interfaces

ECMF04-4HSWM10

Common mode filter with ESD protection for High Speed Serial interfaces

Interfaces and Transceivers

产品型号	描述
STUSB1600	USB Type-C controller (with short-to-VBUS protection)
STUSB1602	USB Type-C controller (with Tx/Rx line driver and BMC)
STUSB1700	USB Type-C controller (with short-to-VBUS protection)
STUSB4500	Stand-alone USB PD controller (with sink Auto-run mode)
STUSB4710	Stand-alone USB PD controller (with short-to-VBUS protection)

产品型号

STUSB1600

USB Type-C controller (with short-to-VBUS protection)

STUSB1602

USB Type-C controller (with Tx/Rx line driver and BMC)

STUSB1700

USB Type-C controller (with short-to-VBUS protection)

STUSB4500

Stand-alone USB PD controller (with sink Auto-run mode)

STUSB4710

Stand-alone USB PD controller (with short-to-VBUS protection)

Microcontrollers & Microprocessors

产品型号	描述
STM32F072CB	Mainstream ARM Cortex-M0 USB line MCU with 128 Kbytes Flash, 48 MHz CPU, USB, CAN and CEC functions
STM32G071GB	Mainstream Arm Cortex-M0+ MCU with 128 Kbytes of Flash memory, 36 Kbytes RAM, 64 MHz CPU, 4x USART, timers, ADC, DAC, comm. I/F, 1.7-3.6V
STM32G431KB	Mainstream Arm Cortex-M4 core with DSP and FPU, 170MHz with 128Kbytes of Flash memory, Math Accelerator, Medium Analog level integration

产品型号

STM32F072CB

Mainstream ARM Cortex-M0 USB line MCU with 128 Kbytes Flash, 48 MHz CPU, USB, CAN and CEC functions

STM32G071GB

Mainstream Arm Cortex-M0+ MCU with 128 Kbytes of Flash memory, 36 Kbytes RAM, 64 MHz CPU, 4x USART, timers, ADC, DAC, comm. I/F, 1.7-3.6V

STM32G431KB

Mainstream Arm Cortex-M4 core with DSP and FPU, 170MHz with 128Kbytes of Flash memory, Math Accelerator, Medium Analog level integration

Protection Devices

产品型号	描述
ESDA25P35-1U1M	High-power transient voltage suppressor (TVS)
ESDA7P120-1U1M	High-power transient voltage supressor (TVS)
ESDAL	DUAL TRANSIL ARRAY FOR ESD PROTECTION
HSP051-4M10	4-line ESD protection for high speed lines
HSP053-4M5	4-line ESD protection for high-speed lines
USBLC6-2SC6Y	Automotive very low capacitance ESD protection

产品型号

ESDA25P35-1U1M

High-power transient voltage suppressor (TVS)

ESDA7P120-1U1M

High-power transient voltage supressor (TVS)

ESDAL

DUAL TRANSIL ARRAY FOR ESD PROTECTION

HSP051-4M10

4-line ESD protection for high speed lines

HSP053-4M5

4-line ESD protection for high-speed lines

USBLC6-2SC6Y

Automotive very low capacitance ESD protection

搜索历史

收藏

USB

精选产品

技术文档

演示和培训资料

出版刊物和宣传资料

设计工具

开发工具硬件

软件

评估工具

EMI Filtering and Signal Conditioning

Interfaces and Transceivers

Microcontrollers & Microprocessors

Protection Devices

搜索历史

收藏

USB

精选 产品

精选 视频

技术文档

演示和培训资料

出版刊物和宣传资料

设计工具

开发工具硬件

软件

评估工具

EMI Filtering and Signal Conditioning

Interfaces and Transceivers

Microcontrollers & Microprocessors

Protection Devices

精选产品

精选视频