概观
解决方案
HW Evaluation Tools
资源
工具和软件
Key Products
开始

Heat metering systems, also called heat cost allocators, are typically used in multi-resident buildings to optimally allocate heat cost based on usage. They estimate heat consumption by measuring the temperature difference between the room and the radiator with data wirelessly transferred to a central unit. Heat cost allocators are battery powered devices and thus low power design is essential to extend battery lifetime expectancy.

We have a large offering of ultra-low power 8 bits STM8L and STM32L 32 bits microcontrollers and ultra-low power sub-GHz connectivity solutions supporting WM-BUS and proprietary mesh protocols, as well as dual NFC/RFID interface tags for device commissioning and temperature monitoring.

In addition we provide a comprehensive set of HW and SW evaluation and development tools to help design ultra-low power, cost effective heat meters.

型号
描述
B-L072Z-LRWAN1 STM32L0 Discovery kit LoRa, Sigfox, low-power wireless Quick view

主要特性

  • CMWX1ZZABZ-091 LoRa® /Sigfox™ module (Murata)
    • Embedded ultra-low-power STM32L072CZ MCU, based on Arm® Cortex® -M0+ core, with 192 Kbytes of Flash memory, 20 Kbytes of RAM, 20 Kbytes of EEPROM
    • Frequency range: 860 MHz - 930 MHz
    • USB 2.0 FS
    • 4-channel,12-bit ADC, 2 × DAC
    • 6-bit timers, LP-UART, I2 C and SPI
    • Embedded SX1276 transceiver
    • LoRa® , FSK, GFSK, MSK, GMSK, and OOK modulations (+ Sigfox™ compatibility)
    • +14 dBm or +20 dBm selectable output power
    • 157 dB maximum link budget
    • Programmable bit rate up to 300 kbit/s
    • High sensitivity: down to -137 dBm
    • Bullet-proof front end: IIP3 = -12.5 dBm
    • 89 dB blocking immunity
    • Low Rx current of 10 mA, 200 nA register retention
    • Fully integrated synthesizer with a resolution of 61 Hz
    • Built-in bit synchronizer for clock recovery
    • Sync word recognition
    • Preamble detection
    • 127 dB+ dynamic range RSSI
    • LoRaWAN™ Class A certified
  • SMA and U.FL RF interface connectors
  • Including 50-ohm SMA RF antenna
  • 7 LEDs:
    • 4 general-purpose LEDs
    • 5 V power LED
    • ST-LINK-communication LED
    • Fault-power LED
  • 1 user and 1 reset push-buttons
  • On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
  • Arduino™ Uno V3 connectors
  • Board power supply through the USB bus or external VIN/3.3 V supply voltage or batteries
  • 3 × AAA-type battery holder for standalone operation
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® , GCC-based IDEs, Arm® Mbed™

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-LDO001V1 Quad high performance LDO evaluation board based on LDBL20, LDLN025, LD39130S and STLQ020 Quick view

主要特性

  • Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
  • Key features:
    • Low operating input voltage (from 1.4 V to 5.5 V)
    • Current capability from 200 mA to 300 mA
    • Low dropout (down to 160 mV typ.)
    • Ultra-low quiescent current (down to 500 nA typ.)
    • Low noise (down to 6.5 μVRMS typ.)
    • High PSSR (up to 80 dB)
    • Logic controlled electronic shutdown (enable)
    • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-STLCS02V1 SensorTile connectable sensor node: solder only Quick view

主要特性

  • Very compact module for motion, audio, environmental sensing and Bluetooth® low energy connectivity with a complete set of firmware examples
  • Mobile connectivity via the STBLESensor app, available for iOS™ and Android™
  • Main components:
    • STM32L476JG – 32-bit ultra-low-power MCU with Cortex® M4F
    • LSM6DSM – iNEMO inertial module: 3D accelerometer and 3D gyroscope
    • LSM303AGR – Ultra-compact high-performance eCompass module: ultra-low power 3D accelerometer and 3D magnetometer
    • LPS22HB – MEMS nano pressure sensor: 260-1260 hPa absolute digital output barometer
    • MP34DT05-A – 64 dB SNR digital MEMS microphone
    • BlueNRG-MS – Bluetooth low energy network processor
    • BALF-NRG-02D3 – 50 Ω balun with integrated harmonic filter
    • LD39115J18R – 150 mA low quiescent current low noise LDO 1.8 V
  • 2 V - 5.5 V power supply range
  • External interfaces: UART, SPI, SAI (Serial Audio Interface), I²C, DFSDM, USB OTG, ADC, GPIOs
  • Solderable only interface (no connector on back side)
  • SWD interface for debugging and programming capability
  • CE certified
  • RoHS and China RoHS compliant
  • WEEE compliant
  • FCC certified
  • IC certified
  • TYPE certified

Show More

IMAGE

Image
Image

FEATURED RESOURCES

BOM Gerber
STEVAL-BCNKT01V1 BlueCoin Starter kit Quick view

主要特性

  • Contains FCC ID: S9NBCOIN01
  • Contains module IC 8976C-BCOIN01 certified with PMN: STEVAL-BCNKT01V1; HVIN: STEVAL-BCNCS01V1; HMN: STEVAL-BCNCR01V1; FVIN: bluenrg_7_2_c_Mode_2-32MHz-XO32K_4M.img
  • The development kit package includes:
    • BlueCoin module (STEVAL-BCNCS01V1) with STM32F446, LSM6DSM, LSM303AGR, LPS22HB, 4x MP34DT06J, BlueNRG-MS, BALF-NRG-01D3, STBC03JR
    • CoinStation (STEVAL-BCNST01V1) board
    • BlueCoin Cradle (STEVAL-BCNCR01V1)
    • 130 mAh Li-Po battery
    • Plastic box for housing the BlueCoin cradle and the battery
    • SWD programming cable
  • Software libraries and tools:
    • STSW-BCNKT01 firmware package with raw sensor data streaming support via USB, data logging on SDCard, audio acquisition and audio streaming, time-of-flight example and BLE protocol to interface to a Smartphone App
    • FP-AUD-SMARTMIC1: smart audio IN-OUT software expansion for STM32Cube
    • FP-SNS-ALLMEMS1: STM32 ODE function pack for BLE and sensors
    • FP-AUD-BVLINK1: BLE and microphones software expansion for STM32Cube
    • STBLESensor: iOS™ and Android™ demo apps
    • BlueST-SDK: iOS and Android software development kit
    • Compatible with STM32 ecosystem through STM32Cube support

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI868V2 Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP Quick view

主要特性

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for Wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX @ +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission, and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
ST25-TAG-BAG-A The ST25-TAG-BAG-A contains six different items based on ST25TA02K and ST25TA64K, two NFC Forum Type 4 Tag ICs with, respectively, 2- and 64-Kbit EEPROM Quick view

主要特性

  • ST25TA02K with a wet inlay 10*17 mm2 copper antenna
  • ST25TA02K with a wet inlay aluminum antenna
  • ST25TA02K with round- and square-stickers aluminum antennas
  • ST25TA64K with a PET card
  • ST25TA64K with a water-proof tag

Show More

IMAGE

Image
Image
ST25-TAG-BAG-E The ST25-TAG-BAG-E contains eight different items based on ST25TA02K and ST25TA64K, two NFC Forum Type 4 Tag ICs with, respectively, 2-Kbit and 64-Kbit EEPROM Quick view

主要特性

  • ST25TA02K NFC seal
  • ST25TA02K NFC stickers
  • ST25TA02K key fob
  • ST25TA02K NFC bracelet
  • ST25TA64K NFC cards
  • ST25TA02K NFC Secure paper label

Show More

IMAGE

Image
Image
CLOUD-ST25TA02KB Evaluation board for ST25TA series Quick view

主要特性

  • Ready-to-use printed circuit board with
    • ST25TA02KB-P NFC/RFID Tag in UFDFPN5 ECOPACK®2 package
    • 19 mm2 single layer inductive antenna, etched on the PCB
  • Contactless interface
    • TruST25™ digital signature
    • NFC Forum Type 4 Tag
    • ISO/IEC 14443 Type A
    • 106 kbps data rate
    • Internal 50 pF tuning capacitance, enabling design of small inductive antennas
  • Memory
    • 256 Byte (2 Kbit) EEPROM with NDEF data support
    • 200-year data retention
    • 1 million erase-write cycles endurance
    • 128-bit password data protection
    • 20-bit event counter for read or write access with anti-tearing feature
  • Digital pad
    • Configurable general purpose output (GPO) indicating, for example, RF field detection

Show More

IMAGE

Image
Image

FEATURED RESOURCES

BOM Gerber
STEVAL-ISA055V1 0.7 A / 1.2 V synchronous buck converter with enable function based on the ST1S12XX Quick view

主要特性

  • RDS(on) typ. 250 m and 400 m
  • Not switching quiescent current: max 600 μA over temperature range
  • Uses tiny capacitors and inductors
  • Internal soft-start
  • Enable function
  • Step-down current mode PWM (1.7 MHz) DCDC converter
  • 0.7 A output current capability
  • Fixed output voltage of 1.2 V
  • Synchronous rectification
  • Typical efficiency: > 90%
  • 3% DC output voltage tolerance

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA141V1 2 A, 2 MHz, Vout = 3.3 V, high-efficiency dual-mode buck-boost DC-DC converter based on the STBB3J Quick view

主要特性

  • Input voltage range from 1.8 V to 5.5 V
  • 2 A output current at 3.3 V in buck mode (VIN = 3.6 V to 5.5 V)
  • 800 mA output current at 3.3 V in boost mode (VIN 2.0 V)
  • Typical efficiency higher than 94%
  • ±2% DC feedback voltage tolerance
  • Automatic transition between step-down and boost mode
  • Adjustable output voltage from 1.2 V to 5.5 V
  • Power save mode (PS) at light load
  • 2.0 MHz fixed switching frequency
  • Adjustable switching frequency up to 2.4 MHz (external synchronous square signal)
  • Device quiescent current less than 50 µA
  • Load disconnect during shutdown
  • Shutdown and soft-start functions
  • Shutdown current <1 A
  • Available in Flip-Chip 20, pitch = 0.4 mm
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
M24SR-DISCOVERY Discovery kit for the M24SR series - Dynamic NFC/RFID tag Quick view

主要特性

  • Ready-to-use printed circuit board (PCB) including:
    • M24SR64-Y Dynamic NFC/RFID tag
    • 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
    • STM32F103RGT6 64LQFP 32-bit microcontroller, with 1Mbytes of Flash memory
    • LCD Color Screen (320*200 pixels)
    • Different color LEDs
    • USB microB connector for board powering
    • JTAG connector for microcontroller firmware upgrade and debug
    • Joystick for menu selection
  • M24SR-DISCO-PREM specific features:
    • Bluetooth module with audio outputs connected to Jack 3.5
    • Headset

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
NUCLEO-L152RE STM32 Nucleo-64 development board with STM32L152RE MCU, supports Arduino and ST morpho connectivity Quick view

主要特性

  • Common features
    • STM32 microcontroller in LQFP64 package
    • 1 user LED shared with Arduino™
    • 1 user and 1 reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External SMPS to generate Vcore logic supply
    • 24 MHz HSE
    • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
    • Arm® Mbed Enabled™ compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-NFC01A1 Dynamic NFC tag expansion board based on M24SR for STM32 Nucleo Quick view

主要特性

  • M24SR64-Y Dynamic NFC/RFID tag IC
  • NFC antenna: 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • Powered through the Arduino UNO R3 connectors
  • 3 color LEDs for general purpose

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IKS01A1 Motion MEMS and environmental sensor expansion board for STM32 Nucleo Quick view

主要特性

  • LSM6DS0: MEMS 3D accelerometer (±2/±4/±8 g) + 3D gyroscope (±245/±500/±2000 dps)
  • LIS3MDL: MEMS 3D magnetometer (±4/ ±8/ ±12/ 16 gauss)
  • LPS25HB*: MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
  • HTS221: capacitive digital relative humidity and temperature
  • DIL 24-pin socket available for additional MEMS adapters and other sensors (UV index)
  • Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
NUCLEO-L476RG STM32 Nucleo-64 development board with STM32L476RG MCU, supports Arduino and ST morpho connectivity Quick view

主要特性

  • Common features
    • STM32 microcontroller in LQFP64 package
    • 1 user LED shared with Arduino™
    • 1 user and 1 reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External SMPS to generate Vcore logic supply
    • 24 MHz HSE
    • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
    • Arm® Mbed Enabled™ compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IDI003V2 Multi-sensor RF platform sensors board Quick view

主要特性

  • Contains the following ST sensors:
    • Pressure sensor LPS25HB
    • Humidity sensor HTS221
    • Accelerometer LIS3DH
    • Microphone MP34DT01
  • AFE for processing the MP34DT01 microphone signal based on TSV522 low power, low offset op-amp
  • Android app available
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDS01A4 Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo Quick view

主要特性

  • STM32 Nucleo expansion board based on the SPSGRF-868
  • SPGRF-868 characteristics:
    • 868 MHz ETSI-certified module based on low power, low data-rate sub-1 GHz SPIRIT1 transceiver
    • Integrated Balun (BALF-SPI-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • Scalable solution; capable of cascading multiple boards for larger systems
  • Example firmware for point-to-point communication, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDS01A5 Sub-1 GHz RF expansion board based on the SPSGRF-915 module for STM32 Nucleo Quick view

主要特性

  • STM32 Nucleo expansion board based on the SPSGRF-915
  • X-NUCLEO-IDS01A5 contains FCC and IC certified module SPSGRF-915 (FCC ID: S9NSPSGRF and IC: 8976C-SPSGRF)
  • SPGRF-915:
    • 915 MHz FCC and IC certified module based on low-power, low-rate sub-1 GHz SPIRIT1 transceiver
    • Integrated Balun (BALF-SPI-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • Scalable solution; can cascade multiple boards for larger systems
  • Example firmware for point-to-point communication, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDB05A1 Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo Quick view

主要特性

  • STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
  • X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
  • SPBTLE-RF:
    • Bluetooth Low Energy FCC and IC certified module based on Bluetooth® SMART 4.1 network processor BlueNRG-MS
    • Integrated Balun (BALF-NRG-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISB035V1 Li-Ion/Li-Po battery power management evaluation board based on STBC03 Quick view

主要特性

  • Charges single-cell Li-Ion/Li-Po batteries with CC-CV algorithm and charge termination
  • Fast charge current programmable from 1 mA to 650 mA
  • Pre-charge current programmable from 1 mA to 650 mA
  • Adjustable floating voltage up to 4.45 V
  • Integrated always-ON low quiescent LDO regulator
  • Battery overcharge and over-discharge protections
  • Overcurrent protection
  • Shipping mode entry and exit inputs
  • Integrated dual 3 Ω SPDT load switches
  • Digital control inputs
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FET001V1 M41T62LC6F adapter board for a standard DIL 24 socket Quick view

主要特性

  • Complete M41T62LC6F pinout (I²C interface) for a standard DIL 24 socket
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-MKI109V3 Professional MEMS tool: ST MEMS adapters motherboard based on the STM32F401VE and compatible with all ST MEMS adapters Quick view

主要特性

  • Compatible with all available ST MEMS adapter boards
  • Controlled by the STM32F401VE high-performance ARM Cortex™ - M4 microcontroller
  • Software-adjustable power circuitry to set sensor supply voltage from 0 to 3.6 V
  • Includes a DIL24 socket for easy MEMS adapter connection
  • Adjustable MEMS DIL24 power supply
  • DFU-compatible for USB microprocessor firmware update
  • USB 2.0 full-speed compliant
  • Embedded power monitoring circuitry on sensor supply voltage and current
  • Debugging connector for SWD/JTAG
  • Can be used with PC software like Unico GUI to manage and analyze MEMS sensor data
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-STLKT01V1 SensorTile development kit Quick view

主要特性

  • Included in the development kit package:
    • SensorTile module (STEVAL-STLCS01V1) with STM32L476JG, LSM6DSM, LSM303AGR, LPS22HB, MP34DT05-A, BlueNRG-MS, BALF-NRG-02D3 and LD39115J18R
    • SensorTile expansion Cradle board equipped with audio DAC, USB port, STM32 Nucleo, Arduino UNO R3 and SWD connector
    • SensorTile Cradle with battery charger, humidity and temperature sensor, SD memory card slot, USB port and breakaway SWD connector
    • 100 mAh Li-Ion battery
    • Plastic box
    • SWD programming cable
  • Software libraries and tools
    • STSW-STLKT01: SensorTile firmware package that supports sensors raw data streaming via USB, data logging on SDCard, audio acquisition and audio streaming.
    • FP-SNS-ALLMEMS1 and FP-SNS-MOTENV1: STM32Cube function packs
    • STBLESensor: iOS and Android demo Apps
    • BlueST-SDK: iOS and Android Software Development Kit
  • CE certified
  • RoHS and China RoHS compliant
  • WEEE compliant
  • FCC (ID: S9NSTILE01) certified
  • IC (IC: 8976C-STILE01) certified with PMN: STEVAL-STLKT01V1; HVIN: STEVAL-STLCS01V1; HMN: STEVAL-STLCX01V1; FVIN: bluenrg_7_1_e_Mode_2-32MHz-XO32K_4M.img
  • TYPE certified (006-000482)

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-STLCS01V1 SensorTile connectable sensor node: plug or solder Quick view

主要特性

  • Very compact module for motion, audio, environmental sensing and Bluetooth® low energy connectivity with a complete set of firmware examples
  • Mobile connectivity via the STBLESensor app, available for iOS™ and Android™
  • Main components:
    • STM32L476JG – 32-bit ultra-low-power MCU with Cortex® M4F
    • LSM6DSM – iNEMO inertial module: 3D accelerometer and 3D gyroscope
    • LSM303AGR – Ultra-compact high-performance eCompass module: ultra-low power 3D accelerometer and 3D magnetometer
    • LPS22HB – MEMS nano pressure sensor: 260-1260 hPa absolute digital output barometer
    • MP34DT05-A – 64 dB SNR digital MEMS microphone
    • BlueNRG-MS – Bluetooth low energy network processor
    • BALF-NRG-02D3 – 50 Ω balun with integrated harmonics filter
    • LD39115J18R – 150 mA low quiescent current low noise LDO 1.8 V
  • 2 V - 5.5 V power supply range
  • External interfaces: UART, SPI, SAI (serial audio interface), I²C, DFSDM, USB OTG, ADC, GPIOs
  • Pluggable or solderable interface
  • SWD interface for debugging and programming capability
  • CE certified
  • RoHS and China RoHS compliant
  • WEEE compliant
  • FCC certified
  • IC certified
  • TYPE certified

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISB041V1 Li-Ion/Li-Po battery power management evaluation board based on STBC02 Quick view

主要特性

  • Charges single-cell Li-Ion/Li-Po batteries with CC-CV algorithm and charge termination
  • Fast charge current programmable from 1 mA to 450 mA
  • Pre-charge current programmable from 1 mA to 450 mA
  • Adjustable floating voltage up to 4.45 V
  • Integrated always-on low quiescent LDO regulator
  • Battery over-charge and over-discharge protections
  • Overcurrent protection
  • Shipping mode exit input
  • Integrated dual 3 Ω SPDT load switches
  • Integrated smart reset / watchdog logic
  • Single wire control interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IKS01A2 Motion MEMS and environmental sensor expansion board for STM32 Nucleo Quick view

主要特性

  • LSM6DSL MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±245/±500/±1000/±2000 dps)
  • LSM303AGR MEMS 3D accelerometer (±2/±4/±8/±16 g) and MEMS3D magnetometer (±50 gauss)
  • LPS22HB MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
  • HTS221: capacitive digital relative humidity and temperature
  • DIL24 socket for additional MEMS adapters and other sensors
  • Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
  • I²C sensor hub features on LSM6DSL available
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-NFC04A1 Dynamic NFC/RFID tag IC expansion board based on ST25DV04K for STM32 Nucleo Quick view

主要特性

  • Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
  • Up to 4-Kbit memory with NDEF support
  • 54 mm diameter, single layer circular antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino™ UNO R3 connector
  • Self-powered or powered through the Arduino™ UNO R3 connectors
  • Three general purpose LEDs
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
  • FCC and IC verified
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI868V1 Sub-1GHz transceiver development kit based on S2-LP Quick view

主要特性

  • S2-LP narrow band ultra-low power sub-1 GHz transceiver in a standalone RF Module tuned for 860 - 940 MHz frequency bands
  • STM32 Nucleo development board with STM32L152RE MCU
  • Suitable for Wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX at +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX / TX operation mode
  • Automatic acknowledgement, retransmission, and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
ST25DV-DISCOVERY Discovery kit for ST25DV04 Dynamic NFC/RFID tag IC with fast transfer mode capability Quick view

主要特性

  • Two ready-to-use printed circuit boards (PCB):
    • ST25DV_Discovery_Mboard:
    • STM32F405VGT6 LQFP100 32-bit microcontroller, with 1 Mbyte Flash memory, 192 + 4 Kbytes SRAM.
    • LCD color screen (320 x 200 pixels)
    • Touch screen driver
    • Different color LEDs (power, user, ST link)
    • User push button
    • Joystick for menu selection
    • Reset button
    • On board ST link for microcontroller firmware upgrade and debug
    • ST link mini USB
    • User micro USB
    • USB micro or mini connector for board powering
    • Demonstration use cases stored in memory
    • Demonstration edition (optional add-on module) with Bluetooth Low Energy module, Wi-Fi® module and JTAG 20 pin connector
  • ST25DV_Discovery_ANT_C5:
    • 40 mm x 24 mm, 13.56 MHz inductive antenna etched on the PCB
    • ST25DV04K Dynamic NFC / RFID tag
    • I2 C interface connector
    • Energy harvesting output (VOUT) with a 10 nF capacitance filtering circuit
    • GPO configurable as RF WIP/BUSY output, to indicate that an RF operation is ongoing

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI915V1 Sub-1GHz transceiver development kit based on S2-LP Quick view

主要特性

  • S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
  • STM32 Nucleo-64 development board with STM32L152RE MCU
  • Suitable for wireless M-Bus systems
  • Suitable for SigFox applications
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +27 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
型号
B-L072Z-LRWAN1

STM32L0 Discovery kit LoRa, Sigfox, low-power wireless

主要特性

  • CMWX1ZZABZ-091 LoRa® /Sigfox™ module (Murata)
    • Embedded ultra-low-power STM32L072CZ MCU, based on Arm® Cortex® -M0+ core, with 192 Kbytes of Flash memory, 20 Kbytes of RAM, 20 Kbytes of EEPROM
    • Frequency range: 860 MHz - 930 MHz
    • USB 2.0 FS
    • 4-channel,12-bit ADC, 2 × DAC
    • 6-bit timers, LP-UART, I2 C and SPI
    • Embedded SX1276 transceiver
    • LoRa® , FSK, GFSK, MSK, GMSK, and OOK modulations (+ Sigfox™ compatibility)
    • +14 dBm or +20 dBm selectable output power
    • 157 dB maximum link budget
    • Programmable bit rate up to 300 kbit/s
    • High sensitivity: down to -137 dBm
    • Bullet-proof front end: IIP3 = -12.5 dBm
    • 89 dB blocking immunity
    • Low Rx current of 10 mA, 200 nA register retention
    • Fully integrated synthesizer with a resolution of 61 Hz
    • Built-in bit synchronizer for clock recovery
    • Sync word recognition
    • Preamble detection
    • 127 dB+ dynamic range RSSI
    • LoRaWAN™ Class A certified
  • SMA and U.FL RF interface connectors
  • Including 50-ohm SMA RF antenna
  • 7 LEDs:
    • 4 general-purpose LEDs
    • 5 V power LED
    • ST-LINK-communication LED
    • Fault-power LED
  • 1 user and 1 reset push-buttons
  • On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
  • Arduino™ Uno V3 connectors
  • Board power supply through the USB bus or external VIN/3.3 V supply voltage or batteries
  • 3 × AAA-type battery holder for standalone operation
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® , GCC-based IDEs, Arm® Mbed™

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-LDO001V1

Quad high performance LDO evaluation board based on LDBL20, LDLN025, LD39130S and STLQ020

主要特性

  • Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
  • Key features:
    • Low operating input voltage (from 1.4 V to 5.5 V)
    • Current capability from 200 mA to 300 mA
    • Low dropout (down to 160 mV typ.)
    • Ultra-low quiescent current (down to 500 nA typ.)
    • Low noise (down to 6.5 μVRMS typ.)
    • High PSSR (up to 80 dB)
    • Logic controlled electronic shutdown (enable)
    • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-STLCS02V1

SensorTile connectable sensor node: solder only

主要特性

  • Very compact module for motion, audio, environmental sensing and Bluetooth® low energy connectivity with a complete set of firmware examples
  • Mobile connectivity via the STBLESensor app, available for iOS™ and Android™
  • Main components:
    • STM32L476JG – 32-bit ultra-low-power MCU with Cortex® M4F
    • LSM6DSM – iNEMO inertial module: 3D accelerometer and 3D gyroscope
    • LSM303AGR – Ultra-compact high-performance eCompass module: ultra-low power 3D accelerometer and 3D magnetometer
    • LPS22HB – MEMS nano pressure sensor: 260-1260 hPa absolute digital output barometer
    • MP34DT05-A – 64 dB SNR digital MEMS microphone
    • BlueNRG-MS – Bluetooth low energy network processor
    • BALF-NRG-02D3 – 50 Ω balun with integrated harmonic filter
    • LD39115J18R – 150 mA low quiescent current low noise LDO 1.8 V
  • 2 V - 5.5 V power supply range
  • External interfaces: UART, SPI, SAI (Serial Audio Interface), I²C, DFSDM, USB OTG, ADC, GPIOs
  • Solderable only interface (no connector on back side)
  • SWD interface for debugging and programming capability
  • CE certified
  • RoHS and China RoHS compliant
  • WEEE compliant
  • FCC certified
  • IC certified
  • TYPE certified

Show More

IMAGE

Image
Image

FEATURED RESOURCES

BOM Gerber
STEVAL-BCNKT01V1

BlueCoin Starter kit

主要特性

  • Contains FCC ID: S9NBCOIN01
  • Contains module IC 8976C-BCOIN01 certified with PMN: STEVAL-BCNKT01V1; HVIN: STEVAL-BCNCS01V1; HMN: STEVAL-BCNCR01V1; FVIN: bluenrg_7_2_c_Mode_2-32MHz-XO32K_4M.img
  • The development kit package includes:
    • BlueCoin module (STEVAL-BCNCS01V1) with STM32F446, LSM6DSM, LSM303AGR, LPS22HB, 4x MP34DT06J, BlueNRG-MS, BALF-NRG-01D3, STBC03JR
    • CoinStation (STEVAL-BCNST01V1) board
    • BlueCoin Cradle (STEVAL-BCNCR01V1)
    • 130 mAh Li-Po battery
    • Plastic box for housing the BlueCoin cradle and the battery
    • SWD programming cable
  • Software libraries and tools:
    • STSW-BCNKT01 firmware package with raw sensor data streaming support via USB, data logging on SDCard, audio acquisition and audio streaming, time-of-flight example and BLE protocol to interface to a Smartphone App
    • FP-AUD-SMARTMIC1: smart audio IN-OUT software expansion for STM32Cube
    • FP-SNS-ALLMEMS1: STM32 ODE function pack for BLE and sensors
    • FP-AUD-BVLINK1: BLE and microphones software expansion for STM32Cube
    • STBLESensor: iOS™ and Android™ demo apps
    • BlueST-SDK: iOS and Android software development kit
    • Compatible with STM32 ecosystem through STM32Cube support

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI868V2

Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP

主要特性

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for Wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX @ +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission, and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
ST25-TAG-BAG-A

The ST25-TAG-BAG-A contains six different items based on ST25TA02K and ST25TA64K, two NFC Forum Type 4 Tag ICs with, respectively, 2- and 64-Kbit EEPROM

主要特性

  • ST25TA02K with a wet inlay 10*17 mm2 copper antenna
  • ST25TA02K with a wet inlay aluminum antenna
  • ST25TA02K with round- and square-stickers aluminum antennas
  • ST25TA64K with a PET card
  • ST25TA64K with a water-proof tag

Show More

IMAGE

Image
Image
ST25-TAG-BAG-E

The ST25-TAG-BAG-E contains eight different items based on ST25TA02K and ST25TA64K, two NFC Forum Type 4 Tag ICs with, respectively, 2-Kbit and 64-Kbit EEPROM

主要特性

  • ST25TA02K NFC seal
  • ST25TA02K NFC stickers
  • ST25TA02K key fob
  • ST25TA02K NFC bracelet
  • ST25TA64K NFC cards
  • ST25TA02K NFC Secure paper label

Show More

IMAGE

Image
Image
CLOUD-ST25TA02KB

Evaluation board for ST25TA series

主要特性

  • Ready-to-use printed circuit board with
    • ST25TA02KB-P NFC/RFID Tag in UFDFPN5 ECOPACK®2 package
    • 19 mm2 single layer inductive antenna, etched on the PCB
  • Contactless interface
    • TruST25™ digital signature
    • NFC Forum Type 4 Tag
    • ISO/IEC 14443 Type A
    • 106 kbps data rate
    • Internal 50 pF tuning capacitance, enabling design of small inductive antennas
  • Memory
    • 256 Byte (2 Kbit) EEPROM with NDEF data support
    • 200-year data retention
    • 1 million erase-write cycles endurance
    • 128-bit password data protection
    • 20-bit event counter for read or write access with anti-tearing feature
  • Digital pad
    • Configurable general purpose output (GPO) indicating, for example, RF field detection

Show More

IMAGE

Image
Image

FEATURED RESOURCES

BOM Gerber
STEVAL-ISA055V1

0.7 A / 1.2 V synchronous buck converter with enable function based on the ST1S12XX

主要特性

  • RDS(on) typ. 250 m and 400 m
  • Not switching quiescent current: max 600 μA over temperature range
  • Uses tiny capacitors and inductors
  • Internal soft-start
  • Enable function
  • Step-down current mode PWM (1.7 MHz) DCDC converter
  • 0.7 A output current capability
  • Fixed output voltage of 1.2 V
  • Synchronous rectification
  • Typical efficiency: > 90%
  • 3% DC output voltage tolerance

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA141V1

2 A, 2 MHz, Vout = 3.3 V, high-efficiency dual-mode buck-boost DC-DC converter based on the STBB3J

主要特性

  • Input voltage range from 1.8 V to 5.5 V
  • 2 A output current at 3.3 V in buck mode (VIN = 3.6 V to 5.5 V)
  • 800 mA output current at 3.3 V in boost mode (VIN 2.0 V)
  • Typical efficiency higher than 94%
  • ±2% DC feedback voltage tolerance
  • Automatic transition between step-down and boost mode
  • Adjustable output voltage from 1.2 V to 5.5 V
  • Power save mode (PS) at light load
  • 2.0 MHz fixed switching frequency
  • Adjustable switching frequency up to 2.4 MHz (external synchronous square signal)
  • Device quiescent current less than 50 µA
  • Load disconnect during shutdown
  • Shutdown and soft-start functions
  • Shutdown current <1 A
  • Available in Flip-Chip 20, pitch = 0.4 mm
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
M24SR-DISCOVERY

Discovery kit for the M24SR series - Dynamic NFC/RFID tag

主要特性

  • Ready-to-use printed circuit board (PCB) including:
    • M24SR64-Y Dynamic NFC/RFID tag
    • 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
    • STM32F103RGT6 64LQFP 32-bit microcontroller, with 1Mbytes of Flash memory
    • LCD Color Screen (320*200 pixels)
    • Different color LEDs
    • USB microB connector for board powering
    • JTAG connector for microcontroller firmware upgrade and debug
    • Joystick for menu selection
  • M24SR-DISCO-PREM specific features:
    • Bluetooth module with audio outputs connected to Jack 3.5
    • Headset

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
NUCLEO-L152RE

STM32 Nucleo-64 development board with STM32L152RE MCU, supports Arduino and ST morpho connectivity

主要特性

  • Common features
    • STM32 microcontroller in LQFP64 package
    • 1 user LED shared with Arduino™
    • 1 user and 1 reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External SMPS to generate Vcore logic supply
    • 24 MHz HSE
    • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
    • Arm® Mbed Enabled™ compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-NFC01A1

Dynamic NFC tag expansion board based on M24SR for STM32 Nucleo

主要特性

  • M24SR64-Y Dynamic NFC/RFID tag IC
  • NFC antenna: 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • Powered through the Arduino UNO R3 connectors
  • 3 color LEDs for general purpose

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IKS01A1

Motion MEMS and environmental sensor expansion board for STM32 Nucleo

主要特性

  • LSM6DS0: MEMS 3D accelerometer (±2/±4/±8 g) + 3D gyroscope (±245/±500/±2000 dps)
  • LIS3MDL: MEMS 3D magnetometer (±4/ ±8/ ±12/ 16 gauss)
  • LPS25HB*: MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
  • HTS221: capacitive digital relative humidity and temperature
  • DIL 24-pin socket available for additional MEMS adapters and other sensors (UV index)
  • Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
NUCLEO-L476RG

STM32 Nucleo-64 development board with STM32L476RG MCU, supports Arduino and ST morpho connectivity

主要特性

  • Common features
    • STM32 microcontroller in LQFP64 package
    • 1 user LED shared with Arduino™
    • 1 user and 1 reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External SMPS to generate Vcore logic supply
    • 24 MHz HSE
    • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
    • Arm® Mbed Enabled™ compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IDI003V2

Multi-sensor RF platform sensors board

主要特性

  • Contains the following ST sensors:
    • Pressure sensor LPS25HB
    • Humidity sensor HTS221
    • Accelerometer LIS3DH
    • Microphone MP34DT01
  • AFE for processing the MP34DT01 microphone signal based on TSV522 low power, low offset op-amp
  • Android app available
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDS01A4

Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo

主要特性

  • STM32 Nucleo expansion board based on the SPSGRF-868
  • SPGRF-868 characteristics:
    • 868 MHz ETSI-certified module based on low power, low data-rate sub-1 GHz SPIRIT1 transceiver
    • Integrated Balun (BALF-SPI-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • Scalable solution; capable of cascading multiple boards for larger systems
  • Example firmware for point-to-point communication, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDS01A5

Sub-1 GHz RF expansion board based on the SPSGRF-915 module for STM32 Nucleo

主要特性

  • STM32 Nucleo expansion board based on the SPSGRF-915
  • X-NUCLEO-IDS01A5 contains FCC and IC certified module SPSGRF-915 (FCC ID: S9NSPSGRF and IC: 8976C-SPSGRF)
  • SPGRF-915:
    • 915 MHz FCC and IC certified module based on low-power, low-rate sub-1 GHz SPIRIT1 transceiver
    • Integrated Balun (BALF-SPI-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • Scalable solution; can cascade multiple boards for larger systems
  • Example firmware for point-to-point communication, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDB05A1

Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo

主要特性

  • STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
  • X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
  • SPBTLE-RF:
    • Bluetooth Low Energy FCC and IC certified module based on Bluetooth® SMART 4.1 network processor BlueNRG-MS
    • Integrated Balun (BALF-NRG-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISB035V1

Li-Ion/Li-Po battery power management evaluation board based on STBC03

主要特性

  • Charges single-cell Li-Ion/Li-Po batteries with CC-CV algorithm and charge termination
  • Fast charge current programmable from 1 mA to 650 mA
  • Pre-charge current programmable from 1 mA to 650 mA
  • Adjustable floating voltage up to 4.45 V
  • Integrated always-ON low quiescent LDO regulator
  • Battery overcharge and over-discharge protections
  • Overcurrent protection
  • Shipping mode entry and exit inputs
  • Integrated dual 3 Ω SPDT load switches
  • Digital control inputs
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FET001V1

M41T62LC6F adapter board for a standard DIL 24 socket

主要特性

  • Complete M41T62LC6F pinout (I²C interface) for a standard DIL 24 socket
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-MKI109V3

Professional MEMS tool: ST MEMS adapters motherboard based on the STM32F401VE and compatible with all ST MEMS adapters

主要特性

  • Compatible with all available ST MEMS adapter boards
  • Controlled by the STM32F401VE high-performance ARM Cortex™ - M4 microcontroller
  • Software-adjustable power circuitry to set sensor supply voltage from 0 to 3.6 V
  • Includes a DIL24 socket for easy MEMS adapter connection
  • Adjustable MEMS DIL24 power supply
  • DFU-compatible for USB microprocessor firmware update
  • USB 2.0 full-speed compliant
  • Embedded power monitoring circuitry on sensor supply voltage and current
  • Debugging connector for SWD/JTAG
  • Can be used with PC software like Unico GUI to manage and analyze MEMS sensor data
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-STLKT01V1

SensorTile development kit

主要特性

  • Included in the development kit package:
    • SensorTile module (STEVAL-STLCS01V1) with STM32L476JG, LSM6DSM, LSM303AGR, LPS22HB, MP34DT05-A, BlueNRG-MS, BALF-NRG-02D3 and LD39115J18R
    • SensorTile expansion Cradle board equipped with audio DAC, USB port, STM32 Nucleo, Arduino UNO R3 and SWD connector
    • SensorTile Cradle with battery charger, humidity and temperature sensor, SD memory card slot, USB port and breakaway SWD connector
    • 100 mAh Li-Ion battery
    • Plastic box
    • SWD programming cable
  • Software libraries and tools
    • STSW-STLKT01: SensorTile firmware package that supports sensors raw data streaming via USB, data logging on SDCard, audio acquisition and audio streaming.
    • FP-SNS-ALLMEMS1 and FP-SNS-MOTENV1: STM32Cube function packs
    • STBLESensor: iOS and Android demo Apps
    • BlueST-SDK: iOS and Android Software Development Kit
  • CE certified
  • RoHS and China RoHS compliant
  • WEEE compliant
  • FCC (ID: S9NSTILE01) certified
  • IC (IC: 8976C-STILE01) certified with PMN: STEVAL-STLKT01V1; HVIN: STEVAL-STLCS01V1; HMN: STEVAL-STLCX01V1; FVIN: bluenrg_7_1_e_Mode_2-32MHz-XO32K_4M.img
  • TYPE certified (006-000482)

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-STLCS01V1

SensorTile connectable sensor node: plug or solder

主要特性

  • Very compact module for motion, audio, environmental sensing and Bluetooth® low energy connectivity with a complete set of firmware examples
  • Mobile connectivity via the STBLESensor app, available for iOS™ and Android™
  • Main components:
    • STM32L476JG – 32-bit ultra-low-power MCU with Cortex® M4F
    • LSM6DSM – iNEMO inertial module: 3D accelerometer and 3D gyroscope
    • LSM303AGR – Ultra-compact high-performance eCompass module: ultra-low power 3D accelerometer and 3D magnetometer
    • LPS22HB – MEMS nano pressure sensor: 260-1260 hPa absolute digital output barometer
    • MP34DT05-A – 64 dB SNR digital MEMS microphone
    • BlueNRG-MS – Bluetooth low energy network processor
    • BALF-NRG-02D3 – 50 Ω balun with integrated harmonics filter
    • LD39115J18R – 150 mA low quiescent current low noise LDO 1.8 V
  • 2 V - 5.5 V power supply range
  • External interfaces: UART, SPI, SAI (serial audio interface), I²C, DFSDM, USB OTG, ADC, GPIOs
  • Pluggable or solderable interface
  • SWD interface for debugging and programming capability
  • CE certified
  • RoHS and China RoHS compliant
  • WEEE compliant
  • FCC certified
  • IC certified
  • TYPE certified

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISB041V1

Li-Ion/Li-Po battery power management evaluation board based on STBC02

主要特性

  • Charges single-cell Li-Ion/Li-Po batteries with CC-CV algorithm and charge termination
  • Fast charge current programmable from 1 mA to 450 mA
  • Pre-charge current programmable from 1 mA to 450 mA
  • Adjustable floating voltage up to 4.45 V
  • Integrated always-on low quiescent LDO regulator
  • Battery over-charge and over-discharge protections
  • Overcurrent protection
  • Shipping mode exit input
  • Integrated dual 3 Ω SPDT load switches
  • Integrated smart reset / watchdog logic
  • Single wire control interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IKS01A2

Motion MEMS and environmental sensor expansion board for STM32 Nucleo

主要特性

  • LSM6DSL MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±245/±500/±1000/±2000 dps)
  • LSM303AGR MEMS 3D accelerometer (±2/±4/±8/±16 g) and MEMS3D magnetometer (±50 gauss)
  • LPS22HB MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
  • HTS221: capacitive digital relative humidity and temperature
  • DIL24 socket for additional MEMS adapters and other sensors
  • Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
  • I²C sensor hub features on LSM6DSL available
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-NFC04A1

Dynamic NFC/RFID tag IC expansion board based on ST25DV04K for STM32 Nucleo

主要特性

  • Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
  • Up to 4-Kbit memory with NDEF support
  • 54 mm diameter, single layer circular antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino™ UNO R3 connector
  • Self-powered or powered through the Arduino™ UNO R3 connectors
  • Three general purpose LEDs
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
  • FCC and IC verified
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI868V1

Sub-1GHz transceiver development kit based on S2-LP

主要特性

  • S2-LP narrow band ultra-low power sub-1 GHz transceiver in a standalone RF Module tuned for 860 - 940 MHz frequency bands
  • STM32 Nucleo development board with STM32L152RE MCU
  • Suitable for Wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX at +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX / TX operation mode
  • Automatic acknowledgement, retransmission, and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
ST25DV-DISCOVERY

Discovery kit for ST25DV04 Dynamic NFC/RFID tag IC with fast transfer mode capability

主要特性

  • Two ready-to-use printed circuit boards (PCB):
    • ST25DV_Discovery_Mboard:
    • STM32F405VGT6 LQFP100 32-bit microcontroller, with 1 Mbyte Flash memory, 192 + 4 Kbytes SRAM.
    • LCD color screen (320 x 200 pixels)
    • Touch screen driver
    • Different color LEDs (power, user, ST link)
    • User push button
    • Joystick for menu selection
    • Reset button
    • On board ST link for microcontroller firmware upgrade and debug
    • ST link mini USB
    • User micro USB
    • USB micro or mini connector for board powering
    • Demonstration use cases stored in memory
    • Demonstration edition (optional add-on module) with Bluetooth Low Energy module, Wi-Fi® module and JTAG 20 pin connector
  • ST25DV_Discovery_ANT_C5:
    • 40 mm x 24 mm, 13.56 MHz inductive antenna etched on the PCB
    • ST25DV04K Dynamic NFC / RFID tag
    • I2 C interface connector
    • Energy harvesting output (VOUT) with a 10 nF capacitance filtering circuit
    • GPO configurable as RF WIP/BUSY output, to indicate that an RF operation is ongoing

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI915V1

Sub-1GHz transceiver development kit based on S2-LP

主要特性

  • S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
  • STM32 Nucleo-64 development board with STM32L152RE MCU
  • Suitable for wireless M-Bus systems
  • Suitable for SigFox applications
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +27 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
00 Files selected for download

技术文档

    • 描述 版本 文档大小 Action
      AN5085
      Cycling endurance and data retention of EEPROMs in ST25DVxxx products based on CMOS F8H process
      2.0
      306.83 KB
      PDF
      AN4653
      Cycling endurance and data retention of high density EEPROM based on CMOS F8H process
      1.0
      267.34 KB
      PDF
      AN4910
      Data exchange between wired (I²C) and wireless (RF ISO 15693) using fast transfer mode supported by ST25DVxxx
      1.0
      585.2 KB
      PDF
      AN4913
      Energy harvesting delivery impact on ST25DVxxx behavior during RF communication
      1.0
      1.05 MB
      PDF
      AN4503
      环境传感器:用于Android 的硬件抽象层
      1.0
      430.49 KB
      PDF
      AN2866
      How to design a 13.56 MHz customized antenna for ST25 NFC / RFID Tags
      3.0
      615.85 KB
      PDF
      AN2972
      How to design an antenna for dynamic NFC tags
      9.0
      1.59 MB
      PDF
      AN934
      How to use the digital calibration feature in TIMEKEEPER® and serial real-time clock (RTC) products
      4.1
      123.42 KB
      PDF
      AN1216
      Implementing a periodic alarm with TIMEKEEPER® and serial real-time clocks (RTCs)
      2.0
      192.89 KB
      PDF
      AN2648
      Increasing the resolution of analog temperature sensors
      1.4
      161.7 KB
      PDF
      AN923
      Managing century information using serial real-time clocks and TIMEKEEPER® NVRAMs
      4.0
      142.23 KB
      PDF
      AN4911
      NDEF management with ST25DVxxx and ST25TVxxx products
      4.0
      460.67 KB
      PDF
      AN576
      PCB layout optimisation
      3.0
      109.53 KB
      PDF
      AN5046
      Printed circuit board assembly recommendations for STMicroelectronics PowerFLAT packages
      4.0
      4.82 MB
      PDF
      AN1019
      Second source for SNAPHAT® using a dual footprint
      2.1
      66.19 KB
      PDF
      AN4433
      将数据存入M24SR 的NDEF 存储器
      1.0
      523.66 KB
      PDF
      AN316
      Transil™ clamping protection mode
      4.3
      432.1 KB
      PDF
      AN4866
      Water resistant features
      1.0
      1.02 MB
      PDF
      AN5085

      Cycling endurance and data retention of EEPROMs in ST25DVxxx products based on CMOS F8H process

      AN4653

      Cycling endurance and data retention of high density EEPROM based on CMOS F8H process

      AN4910

      Data exchange between wired (I²C) and wireless (RF ISO 15693) using fast transfer mode supported by ST25DVxxx

      AN4913

      Energy harvesting delivery impact on ST25DVxxx behavior during RF communication

      AN4503

      环境传感器:用于Android 的硬件抽象层

      AN2866

      How to design a 13.56 MHz customized antenna for ST25 NFC / RFID Tags

      AN2972

      How to design an antenna for dynamic NFC tags

      AN934

      How to use the digital calibration feature in TIMEKEEPER® and serial real-time clock (RTC) products

      AN1216

      Implementing a periodic alarm with TIMEKEEPER® and serial real-time clocks (RTCs)

      AN2648

      Increasing the resolution of analog temperature sensors

      AN923

      Managing century information using serial real-time clocks and TIMEKEEPER® NVRAMs

      AN4911

      NDEF management with ST25DVxxx and ST25TVxxx products

      AN576

      PCB layout optimisation

      AN5046

      Printed circuit board assembly recommendations for STMicroelectronics PowerFLAT packages

      AN1019

      Second source for SNAPHAT® using a dual footprint

      AN4433

      将数据存入M24SR 的NDEF 存储器

      AN316

      Transil™ clamping protection mode

      AN4866

      Water resistant features

    • 描述 版本 文档大小 Action
      TN1198
      HLGA封装中MEMS传感器的表面贴装指南
      1.0
      240.09 KB
      PDF
      TN0018
      LGA 封装中MEMS 传感器的表面贴装指南
      1.0
      251.2 KB
      PDF
      TN1198

      HLGA封装中MEMS传感器的表面贴装指南

      TN0018

      LGA 封装中MEMS 传感器的表面贴装指南

演示和培训资料

    • 描述 版本 文档大小 Action
      EEPROM 2 Mbit highest density memories 1.0
      2.49 MB
      PDF
      IoT connectivity made easier with STM32 MCUs and LoRa 1.3
      2.85 MB
      PDF
      ST25DV-I2C product presentation 2.2
      2.1 MB
      PDF

      EEPROM 2 Mbit highest density memories

      IoT connectivity made easier with STM32 MCUs and LoRa

      ST25DV-I2C product presentation

出版刊物和宣传资料

    • 描述 版本 文档大小 Action
      Battery management ICs - STBC02/03 Li-Ion charger with load switches and smart reset generator 04.2017
      730.72 KB
      PDF
      NFC / RFID tags M24SR series 2.0
      1.28 MB
      PDF
      NFC /RFID tags ST25TA series 1.0
      1.36 MB
      PDF
      Power Delivery Protection - Simply cancel ESD and EOS events 1.0
      519.6 KB
      PDF
      s2-LP:超低功耗、高性能、Sub-1 HGz RF收发器 3.0
      824.66 KB
      PDF
      ST Protection Finder - The new app for Android and iOS 1.0
      1.52 MB
      PDF
      ST25DV系列动态NFC/RFID标签 ISO/IEC 15693 NFC Forum Type 5 1.1
      265.36 KB
      PDF
      ST25TV series - Tags for Consumer Engagement flyer 1.0
      1.22 MB
      PDF
      Ultra-low clamping voltage 0201 ESD diodes 1.0
      527.9 KB
      PDF

      Battery management ICs - STBC02/03 Li-Ion charger with load switches and smart reset generator

      NFC / RFID tags M24SR series

      NFC /RFID tags ST25TA series

      Power Delivery Protection - Simply cancel ESD and EOS events

      s2-LP:超低功耗、高性能、Sub-1 HGz RF收发器

      ST Protection Finder - The new app for Android and iOS

      ST25DV系列动态NFC/RFID标签 ISO/IEC 15693 NFC Forum Type 5

      ST25TV series - Tags for Consumer Engagement flyer

      Ultra-low clamping voltage 0201 ESD diodes

    • 描述 版本 文档大小 Action
      EEPROM selection guide 2.0
      1,007.87 KB
      PDF
      Linear and Switching Voltage Regulators Selection Guide 3.0
      370.88 KB
      PDF
      Protection devices and integrated EMI filtering selection guide 2.0
      743.69 KB
      PDF

      EEPROM selection guide

      Linear and Switching Voltage Regulators Selection Guide

      Protection devices and integrated EMI filtering selection guide

    • 描述 版本 文档大小 Action
      Power management for handheld and portable 2.0
      1.09 MB
      PDF

      Power management for handheld and portable

设计工具

    • 型号

      Transient voltage suppressor smart selection tool

开发工具硬件

软件

    • 型号

      Embedded software samples for BlueCoin: data streaming via USB and BLE, logging on SD card, gesture recognition, audio acquisition and playback

      Evaluation SW package based on S2-LP

      STEVAL-WESU1 Android/iOS app

    • 型号

      STM32 ODE function pack for IoT node with BLE connectivity, digital microphone, environmental and motion sensors

      STM32Cube function pack for IoT node with BLE connectivity and environmental and motion sensors

      Sensor and DSP algorithm software expansion for STM32Cube

      Sensor and motion algorithm software expansion for STM32Cube

      STM32Cube expansion software for X-NUCLEO-NFC01A1

      Dynamic NFC/RFID tag IC software expansion for STM32Cube

      STM32 Sigfox software expansion for STM32Cube

    • 型号

      Standard C platform-independent drivers for MEMS motion and environmental sensors

    • 型号

      Application executable of the "NFC Tap" Android app for ST25 product family

      Firmware for ST25DV-DISCOVERY kit

      Application executable of the "NFC Tap" iOS app for ST25 product family

      Software Development Kit for ST25 Tags and Dynamic Tags

eDesignSuite

转换器

Input

V This option is required. And must be less than or equal to Volt. Max [V]
V This option is required. And must be greater than or equal to Volt. Min [V]

Output Power

V This option is required and must be a number.
A This option is required and must be a number.

Clocks and Timers

型号 描述
M41T0 Serial real-time clock (RTC)
M41T80 Serial real-time clock (RTC) with alarm
型号
Serial real-time clock (RTC)
Serial real-time clock (RTC) with alarm

EMI Filtering and Signal Conditioning

型号 描述
BALF-NRG-02D3 50Ω / conjugate match balun to BlueNRG transceiver, with integrated harmonic filter
BALF-SPI2-01D3 50 Ω nominal input / conjugate match balun to S2-LP,868 - 930 MHz with integrated harmonic filter
型号
50Ω / conjugate match balun to BlueNRG transceiver, with integrated harmonic filter
50 Ω nominal input / conjugate match balun to S2-LP,868 - 930 MHz with integrated harmonic filter

MEMS and Sensors

型号 描述
HTS221 Capacitive digital sensor for relative humidity and temperature
STTS751 2.25 V low-voltage local digital temperature sensor
型号
Capacitive digital sensor for relative humidity and temperature
2.25 V low-voltage local digital temperature sensor

电源管理

型号 描述
LD39020 200 mA very low quiescent current Linear regulator IC
LD39130S 300 mA very low quiescent current Linear regulator IC with automatic Green mode
LDK120 200 mA low quiescent current very low noise LDO
LDK130 300 mA low quiescent current very low noise LDO
STBC02 Li-Ion linear battery charger with LDO, load switches and reset generator
STBC03 Li-Ion linear battery charger with LDO and load switches
STLQ020 200 mA ultra-low quiescent current LDO
STNS01 Li-Ion Linear Battery Charger with LDO
型号
200 mA very low quiescent current Linear regulator IC
300 mA very low quiescent current Linear regulator IC with automatic Green mode
200 mA low quiescent current very low noise LDO
300 mA low quiescent current very low noise LDO
Li-Ion linear battery charger with LDO, load switches and reset generator
Li-Ion linear battery charger with LDO and load switches
200 mA ultra-low quiescent current LDO
Li-Ion Linear Battery Charger with LDO

Power Transistors

型号 描述
STL120N8F7 N-channel 80 V, 3.7 mOhm typ., 120 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
STL150N3LLH6 N-channel 30 V, 0.0016 Ohm typ., 33 A STripFET(TM) VI DeepGATE(TM) Power MOSFET in PowerFLAT(TM) 5x6 package
STL160N4F7 N-channel 40 V, 2.1 mOhm typ., 120 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
STL20N6F7 N-channel 60 V, 0.0046 Ohm typ., 20 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package
STL50N6F7 N-channel 60 V, 9 mOhm typ., 60 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
型号
N-channel 80 V, 3.7 mOhm typ., 120 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
N-channel 30 V, 0.0016 Ohm typ., 33 A STripFET(TM) VI DeepGATE(TM) Power MOSFET in PowerFLAT(TM) 5x6 package
N-channel 40 V, 2.1 mOhm typ., 120 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
N-channel 60 V, 0.0046 Ohm typ., 20 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package
N-channel 60 V, 9 mOhm typ., 60 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package

Protection Devices

型号 描述
ESDA25P35-1U1M High-power transient voltage suppressor (TVS)
ESDA7P120-1U1M High-power transient voltage supressor (TVS)
SMAJ 400 W TVS in SMA
型号
High-power transient voltage suppressor (TVS)
High-power transient voltage supressor (TVS)
400 W TVS in SMA

Wireless Transceivers, MCUs and Modules

型号 描述
S2-LP Ultra-low power, high performance, sub-1GHz transceiver
型号
Ultra-low power, high performance, sub-1GHz transceiver