血糖仪

主要特性

• STM32L152RBT6 (128 KB Flash memory, 16 KB RAM, 4 KB EEPROM) or STM32L152RCT6 (256 KB Flash memory, 32 KB RAM, 8 KB EEPROM) microcontroller in an LQFP64 package
• On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone ST-LINK/V2 (with SWD connector for programming and debugging)
• Board power supply: through USB bus or from an external 3.3 or 5 V supply voltage
• External application power supply: 3 V and 5 V
• I_DD current measurement
• LCD
  • DIP28 package
  • 24 segments, 4 commons
• Four LEDs:
  • LD1 (red/green) for USB communication
  • LD2 (red) for 3.3 V power-on
  • Two user LEDs, LD3 (green) and LD4 (blue)
• Two pushbuttons (user and reset)
• One linear touch sensor or four touchkeys
• Extension header for LQFP64 I/Os for quick connection to prototyping board and easy probing
• Comprehensive free software including a variety of examples, part of STSW-STM32072 package

Show More

主要特性

• STM32L053C8T6 microcontroller featuring 64 KB of Flash memory, 8 KB RAM in an LQFP48 package.
• On-board ST-LINK/V2-1 with selection mode switch to use the kit as a standalone ST-LINK/V2-1 (with SWD connector for programming and debugging)
• mbed™-enabled (mbed.org)
• USB ST-LINK with re-enumeration capability and three different interfaces:
  • virtual com port
  • mass storage
  • debug port
• Board power supply: through USB bus or from an external 5 V supply voltage
• External application power supply: 3 V and 5 V.
• One linear touch sensor or four touchkeys.
• IDD current measurement.
• 2.04” E-paper display, 172x72 pixels
• Four LEDs:
  • LD1 (red/green) for USB communication
  • LD2 (red) for 3.3 V power-on
  • Two user LEDs: LD3 (green), LD4 (red)
• Two pushbuttons (user and reset)
• Extension header for LQFP48 I/Os for a quick connection to the prototyping board and easy probing
• Comprehensive free software including a variety of examples, part of STM32CubeL0 package

Show More

主要特性

• STM32L496AGI6 microcontroller featuring 1 Mbyte of Flash memory and 320 Kbytes of RAM in an UFBGA169 package
• 1.54 inch 240 x 240 pixel-TFT color LCD with parallel interface
• SAI Audio CODEC, with a stereo headset jack, including analog microphone input
• Stereo digital MEMS microphones
• microSD™ card connector (card included)
• Camera 8 bit-connector
• STMod+ and PMOD connectors
• 8 Mbit-PSRAM
• IDD measurement
• 64 Mbit-Quad-SPI Flash
• 8 LEDs
• Reset push button
• 4 direction-joystick with selection
• USB OTG FS with Micro-AB connector
• Compatible Arduino™ Uno V3 connectors
• On-board ST-LINK/V2-1 debugger
• USB ST-LINK functions: Virtual COM port, mass storage, debug port
• 5 source options for power supply
  • ST-LINK/V2-1 USB connector
  • User USB FS connector
  • VIN from Arduino™ connector
  • 5 V from Arduino™ connector
  • USB charger
• 2 possible supply voltages for the MCU: 1.8 V and 3.3 V
• Comprehensive free software including a variety of examples, part of the STM32Cube package

Show More

主要特性

• Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
• Key features:
  • Low operating input voltage (from 1.4 V to 5.5 V)
  • Current capability from 200 mA to 300 mA
  • Low dropout (down to 160 mV typ.)
  • Ultra-low quiescent current (down to 500 nA typ.)
  • Low noise (down to 6.5 μVRMS typ.)
  • High PSSR (up to 80 dB)
  • Logic controlled electronic shutdown (enable)
  • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
• RoHS compliant

Show More

主要特性

• STM32L4R9AII6 microcontroller with 2-Mbyte Flash memory and 640-Kbyte RAM in UFBGA169 package
• 1.2” 390x390 pixel AMOLED round display panel with 16-million colors depth, MIPI^® DSI interface, and capacitive touch panel
• USB OTG FS
• On-board current measurement
• SAI audio codec
• ST-MEMS digital microphones
• 16-Mbit asynchronous PSRAM
• 512-Mbit Octo-SPI Flash
• 2 user LEDs
• 1 reset push-button
• 4-direction joystick with selection button
• Board connectors:
  • 8-bit camera
  • USB OTG FS with Micro-AB
  • Stereo headset jack including analog microphone input
  • microSD™ card
• Board expansion connectors:
  • Arduino™ Uno V3
  • STMod+
  • PMOD
  • EXT_I2C
• Flexible power-supply options:
  • ST-LINK USB V_BUS or external sources
• On-board ST-LINK/V2-1 debugger/programmer with USBre-enumeration capability: mass storage, virtual COM port and debug port
• Comprehensive free software libraries and examples available with the STM32Cube package
• Support of a wide choice of integrated development environments (IDEs), including IAR™, Keil^® and GCC-based IDEs

Show More