L9907

批量生产
Education

3 phase gate driver for 6step or FOC controlled Brushless Motors compatible with 48V NET

下载数据手册

Order from our eStore and our distributors

立即购买
概述
资源
工具与软件
解决方案
eDesignSuite
质量与可靠性
Sales Briefcase
开始
样片和购买
Partner products
  • 主要特性

    • AEC-Q100 qualified
    • Supply voltage from 4.2V to 54 V for working in single (12 V systems), double (24 V systems) and 48 V battery applications
    • The device can withstand -7 V to 90 V at the FET high-side Driver pins
    • Low standby current consumption
    • 3.3 V internal regulator supplied by Vcc pin
    • Boost regulator for full Rdson down to 6 V and over voltage protection
    • 3 low-side + 3 high-side drivers
      • PWM operation up to 20 kHz
      • Gate driver current adjustable via SPI in 4 steps. Range set via external resistor. Maximum gate controlled current 600 mA
      • Source connection to each MOSFET
    • Input pin for each gate driver
    • 2-differential current sense amplifiers:
      • Output offset selectable via SPI (0.2*Vcc offset for ground shunt resistors connection, 0.5*Vcc offset for phase shunt resistors connection)
      • All the amplifier gain factors are programmable (10, 30, 50, 100)
    • 8 MHz, 16-bit SPI
      • Full diagnostic
      • Programmable parameters:
        • Cross conduction dead time with a fixed minimum value
        • 4 current steps driving the PowerMOS gates (25%, 50%, 75%, 100%)
        • Phase or ground selection of current sense amplifier
        • Gain values for the current sense amplifiers
        • Zero current output voltage (offset) for the current sense amplifiers
        • Over voltage threshold selection for single or double battery operation
        • Short circuit detection thresholds for the low-side and the high-side MOSFETs (drain to source voltage monitor).
    • Protection and diagnostic
      • FET driver:
        • FET driver supply Undervoltage (UV) diagnostic;
        • Gate to source output voltage limit;
        • Gate to source passive switch off.
      • Power supply pins VB and VCC:
        • Overvoltage (OV), Undervoltage (UV) diagnostic and protection
      • All logic pins withstand 35 V
      • Power MOSFET drain to source voltage drop measurement for overcurrent protection
      • Over-temperature diagnostic and shutdown
      • Fault status flag output

样片和购买

产品型号
封装
包装类型
温度(ºC) 供货状态
ECCN (US)
Country of Origin
Budgetary Price (US$)*/Qty
从ST订购
从分销商订购
最小值
最大值
L9907TR TQFP 64 10x10x1.0 Tape And Reel - -
批量生产
EAR99 MALAYSIA 5.4 / 1k 立即购买 查看供货情况

...的经销商可用性L9907TR

代理商名称
地区 库存 最小订购量 第三方链接
DIGIKEY WORLDWIDE 796 1 马上订购
MOUSER WORLDWIDE 1562 1 马上订购

代理商库存报告日期: 2020-05-20

代理商名称

DIGIKEY

库存

796

Min.Order

1

地区

WORLDWIDE 马上订购

MOUSER

库存

1562

Min.Order

1

地区

WORLDWIDE 马上订购

代理商库存报告日期: 2020-05-20

L9907 TQFP 64 10x10x1.0 Tray - -
批量生产
EAR99 MALAYSIA 5.4 / 1k 没有经销商,请联系我们的销售办事处

L9907TR

封装

TQFP 64 10x10x1.0

包装类型

Tape And Reel

Budgetary Price (US$)*/Qty

5.4 / 1k

...的经销商可用性L9907TR

代理商名称
地区 库存 最小订购量 第三方链接
DIGIKEY WORLDWIDE 796 1 马上订购
MOUSER WORLDWIDE 1562 1 马上订购

代理商库存报告日期: 2020-05-20

代理商名称

DIGIKEY

库存

796

Min.Order

1

地区

WORLDWIDE 马上订购

MOUSER

库存

1562

Min.Order

1

地区

WORLDWIDE 马上订购

代理商库存报告日期: 2020-05-20

Operating Temperature (°C)

(最小值)

-

(最大值)

-

供货状态

批量生产

Budgetary Price (US$)* / Qty

5.4 / 1k

ECCN (US)

EAR99

Country of Origin

MALAYSIA

L9907

封装

TQFP 64 10x10x1.0

包装类型

Tray

Budgetary Price (US$)*/Qty

5.4 / 1k

Operating Temperature (°C)

(最小值)

-

(最大值)

-

供货状态

批量生产

Budgetary Price (US$)* / Qty

5.4 / 1k

ECCN (US)

EAR99

Country of Origin

MALAYSIA

(*) 建议转售单价(美元)仅用于预算用途。如需以当地货币计价的报价,请联系您当地的 ST销售办事处 或我们的 经销商

适合您的资源

评估工具

    • 产品型号

      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V

      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V - high Current version (120Amps)

00 选择要下载的文档

技术文档

    • 描述 版本 文档大小 操作
      DS11800
      Automotive FET driver for 3 phase BLDC motor
      3.0
      787.76 KB
      PDF
      DS11800

      Automotive FET driver for 3 phase BLDC motor

    • 描述 版本 文档大小 操作
      AN5124
      Supply voltage configuration of 3-phase BLDC automotive MOSFET driver L9907
      1.0
      2.64 MB
      PDF
      AN5124

      Supply voltage configuration of 3-phase BLDC automotive MOSFET driver L9907

    • 描述 版本 文档大小 操作
      AN5124
      Supply voltage configuration of 3-phase BLDC automotive MOSFET driver L9907
      1.0
      2.64 MB
      PDF
      AN5124

      Supply voltage configuration of 3-phase BLDC automotive MOSFET driver L9907

出版刊物和宣传资料

    • 描述 版本 文档大小 操作
      ST’s solutions for automotive seating systems 1.0
      1.3 MB
      PDF

      ST’s solutions for automotive seating systems

    • Combining the SPC56P-Discovery board and EVAL-L9907 (up to 20A) or EVAL-L9907H (up to 120A) evaluation board with related Graphical User Interface (GUI) STSW-L9907 or STSW-L9907-H, you can easily evaluate your brushless motor control applications.
      解决方案组件
      产品型号 描述 状态 核心产品 价格 (US$)*
      订购 / 下载
      L9907

      主要特性

      • AEC-Q100 qualified
      • Supply voltage from 4.2V to 54 V for working in single (12 V systems), double (24 V systems) and 48 V battery applications
      • The device can withstand -7 V to 90 V at the FET high-side Driver pins
      • Low standby current consumption
      • 3.3 V internal regulator supplied by Vcc pin
      • Boost regulator for full Rdson down to 6 V and over voltage protection
      • 3 low-side + 3 high-side drivers
        • PWM operation up to 20 kHz
        • Gate driver current adjustable via SPI in 4 steps. Range set via external resistor. Maximum gate controlled current 600 mA
        • Source connection to each MOSFET
      • Input pin for each gate driver
      • 2-differential current sense amplifiers:
        • Output offset selectable via SPI (0.2*Vcc offset for ground shunt resistors connection, 0.5*Vcc offset for phase shunt resistors connection)
        • All the amplifier gain factors are programmable (10, 30, 50, 100)
      • 8 MHz, 16-bit SPI
        • Full diagnostic
        • Programmable parameters:
          • Cross conduction dead time with a fixed minimum value
          • 4 current steps driving the PowerMOS gates (25%, 50%, 75%, 100%)
          • Phase or ground selection of current sense amplifier
          • Gain values for the current sense amplifiers
          • Zero current output voltage (offset) for the current sense amplifiers
          • Over voltage threshold selection for single or double battery operation
          • Short circuit detection thresholds for the low-side and the high-side MOSFETs (drain to source voltage monitor).
      • Protection and diagnostic
        • FET driver:
          • FET driver supply Undervoltage (UV) diagnostic;
          • Gate to source output voltage limit;
          • Gate to source passive switch off.
        • Power supply pins VB and VCC :
          • Overvoltage (OV), Undervoltage (UV) diagnostic and protection
        • All logic pins withstand 35 V
        • Power MOSFET drain to source voltage drop measurement for overcurrent protection
        • Over-temperature diagnostic and shutdown
        • Fault status flag output

      显示较多内容

      3 phase gate driver for 6step or FOC controlled Brushless Motors compatible with 48V NET
      批量生产
      8.98 立即购买
      EVAL-L9907-H

      主要特性

      • Supply voltage range (VBatt): 6 V÷54 V
      • Load Current Capability up to 120 A
      • Device control and diagnostic via SPI
      • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
      • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
      • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
      • Total accessibility to all pins by test points
      • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
      • Possibility to connect external USB adapter for the SPI communication
      • Possibility to use external Boost components by removing jumpers

      显示较多内容

      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V - high Current version (120Amps)
      批量生产
      L9907 269.50 立即购买
      EVAL-L9907

      主要特性

      • Supply voltage range (VBatt): 6 V÷54 V
      • Load Current Capability up to 20 A
      • Device control and diagnostic via SPI
      • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
      • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
      • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
      • Total accessibility to all pins by test points
      • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
      • Possibility to connect external USB adapter for the SPI communication
      • Possibility to use external Boost components by removing jumpers

      显示较多内容

      IMAGE

      EVAL-L9907
      EVAL-L9907
      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V
      批量生产
      L9907 280.0
      SPC56P-Discovery

      主要特性

      • SPC560P50L5 32-bit 64MHz e200z0h CPU;32-bit Power Architecture® Technology CPU, 576 KB Flash in an LQFP144 package.
      • Shield Connectors (Arduinocompatible).
      • On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers (2 x 7 male 100mil connector).
      • Free 128 Kbyte code size limited debugging
      • Board power supply: from the USB bus (5 V supply voltage) or through external +12 V PSU.
      • All GPIOs and DSPI/USB signals accessible by a 4x37 100mil pin grid array allowing connection of an additional boards for dedicated applications.
      • CAN, K-LINE, LIN, FlexRay interfaces.
      • Main power switch.
      • Reset push button.
      • 2 potentiometers for ADC evaluation
      • 12 MHz crystal.
      • Board size 152 x 103 mm

      显示较多内容

      IMAGE

      SPC56P-Discovery
      SPC56P-Discovery

      特色资源

      Gerber
      Discovery Kit for SPC56 P line - with SPC560P50L5 MCU
      批量生产
      98.47 立即购买
      STSW-L9907-H

      主要特性

      • Complete Graphical User Interface (GUI) for EVAL-L9907H evaluation board.

      显示较多内容

      EVAL-L9907-H Graphical User Interface
      批量生产
      -
      软件
      产品型号 Software Version 供货状态 供应商 下载
      STSW-L9907-H 3.0.0 Active ST
      STSW-L9907

      主要特性

      • Complete Graphical User Interface (GUI) for EVAL-L9907 evaluation board.

      显示较多内容

      EVAL-L9907 Graphical User Interface
      批量生产
      -
      软件
      产品型号 Software Version 供货状态 供应商 下载
      STSW-L9907 3.0.0 Active ST
      L9907

      Description:

      3 phase gate driver for 6step or FOC controlled Brushless Motors compatible with 48V NET

      价格 (US$)*

      8.98

      Key features

      • AEC-Q100 qualified
      • Supply voltage from 4.2V to 54 V for working in single (12 V systems), double (24 V systems) and 48 V battery applications
      • The device can withstand -7 V to 90 V at the FET high-side Driver pins
      • Low standby current consumption
      • 3.3 V internal regulator supplied by Vcc pin
      • Boost regulator for full Rdson down to 6 V and over voltage protection
      • 3 low-side + 3 high-side drivers
        • PWM operation up to 20 kHz
        • Gate driver current adjustable via SPI in 4 steps. Range set via external resistor. Maximum gate controlled current 600 mA
        • Source connection to each MOSFET
      • Input pin for each gate driver
      • 2-differential current sense amplifiers:
        • Output offset selectable via SPI (0.2*Vcc offset for ground shunt resistors connection, 0.5*Vcc offset for phase shunt resistors connection)
        • All the amplifier gain factors are programmable (10, 30, 50, 100)
      • 8 MHz, 16-bit SPI
        • Full diagnostic
        • Programmable parameters:
          • Cross conduction dead time with a fixed minimum value
          • 4 current steps driving the PowerMOS gates (25%, 50%, 75%, 100%)
          • Phase or ground selection of current sense amplifier
          • Gain values for the current sense amplifiers
          • Zero current output voltage (offset) for the current sense amplifiers
          • Over voltage threshold selection for single or double battery operation
          • Short circuit detection thresholds for the low-side and the high-side MOSFETs (drain to source voltage monitor).
      • Protection and diagnostic
        • FET driver:
          • FET driver supply Undervoltage (UV) diagnostic;
          • Gate to source output voltage limit;
          • Gate to source passive switch off.
        • Power supply pins VB and VCC :
          • Overvoltage (OV), Undervoltage (UV) diagnostic and protection
        • All logic pins withstand 35 V
        • Power MOSFET drain to source voltage drop measurement for overcurrent protection
        • Over-temperature diagnostic and shutdown
        • Fault status flag output

      显示较多内容

      EVAL-L9907-H

      Description:

      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V - high Current version (120Amps)

      价格 (US$)*

      269.50

      Key features

      • Supply voltage range (VBatt): 6 V÷54 V
      • Load Current Capability up to 120 A
      • Device control and diagnostic via SPI
      • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
      • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
      • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
      • Total accessibility to all pins by test points
      • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
      • Possibility to connect external USB adapter for the SPI communication
      • Possibility to use external Boost components by removing jumpers

      显示较多内容

      FEATURED RESOURCES

      schematics gerber
      EVAL-L9907

      Description:

      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V

      价格 (US$)*

      280.0

      Key features

      • Supply voltage range (VBatt): 6 V÷54 V
      • Load Current Capability up to 20 A
      • Device control and diagnostic via SPI
      • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
      • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
      • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
      • Total accessibility to all pins by test points
      • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
      • Possibility to connect external USB adapter for the SPI communication
      • Possibility to use external Boost components by removing jumpers

      显示较多内容

      IMAGE

      EVAL-L9907
      EVAL-L9907

      FEATURED RESOURCES

      schematics gerber
      SPC56P-Discovery

      Description:

      Discovery Kit for SPC56 P line - with SPC560P50L5 MCU

      价格 (US$)*

      98.47

      Key features

      • SPC560P50L5 32-bit 64MHz e200z0h CPU;32-bit Power Architecture® Technology CPU, 576 KB Flash in an LQFP144 package.
      • Shield Connectors (Arduinocompatible).
      • On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers (2 x 7 male 100mil connector).
      • Free 128 Kbyte code size limited debugging
      • Board power supply: from the USB bus (5 V supply voltage) or through external +12 V PSU.
      • All GPIOs and DSPI/USB signals accessible by a 4x37 100mil pin grid array allowing connection of an additional boards for dedicated applications.
      • CAN, K-LINE, LIN, FlexRay interfaces.
      • Main power switch.
      • Reset push button.
      • 2 potentiometers for ADC evaluation
      • 12 MHz crystal.
      • Board size 152 x 103 mm

      显示较多内容

      IMAGE

      SPC56P-Discovery
      SPC56P-Discovery

      FEATURED RESOURCES

      gerber
      STSW-L9907-H

      Description:

      EVAL-L9907-H Graphical User Interface

      价格 (US$)*

      -
      软件

      Key features

      • Complete Graphical User Interface (GUI) for EVAL-L9907H evaluation board.

      显示较多内容

      产品型号 Software Version 供货状态 供应商 下载
      STSW-L9907-H 3.0.0 Active ST
      STSW-L9907

      Description:

      EVAL-L9907 Graphical User Interface

      价格 (US$)*

      -
      软件

      Key features

      • Complete Graphical User Interface (GUI) for EVAL-L9907 evaluation board.

      显示较多内容

      产品型号 Software Version 供货状态 供应商 下载
      STSW-L9907 3.0.0 Active ST

产品型号 供货状态 封装 等级规格 符合RoHS级别 材料声明**
L9907
批量生产
TQFP 64 10x10x1.0 Automotive Ecopack2
L9907TR
批量生产
TQFP 64 10x10x1.0 Automotive Ecopack2

L9907

Package:

TQFP 64 10x10x1.0

Material Declaration**:

PDF XML

Marketing Status

批量生产

Package

TQFP 64 10x10x1.0

Grade

Automotive

RoHS Compliance Grade

Ecopack2

L9907TR

Package:

TQFP 64 10x10x1.0

Material Declaration**:

PDF XML

Marketing Status

批量生产

Package

TQFP 64 10x10x1.0

Grade

Automotive

RoHS Compliance Grade

Ecopack2

(**) st.com上提供的材料声明表单可能是基于包装系列中最常用的封装的通用文档。因此,它们可能不是100%适用于特定的设备。有关特定设备的信息,请联系 销售支持