-
This microcontroller is a 32-bit system-on-chip (SoC) device intended for use in mid-range engine control and automotive transmission control applications.
It is compatible with devices in ST's SPC56xx family and offers performance and capability above that of the SPC563M devices.
The microcontroller's e200z4 host processor core is built on the Power Architecture technology and designed specifically for embedded applications. In addition to the Power Architecture technology, this core supports instructions for digital signal processing (DSP).
The device has two levels of memory hierarchy consisting of 8 KB of instruction cache, backed by a 128 KB on-chip SRAM and a 2 MB internal flash memory.
For development, the device includes a calibration bus that is accessible only when using the STMicroelectronics calibration tool.主要特性
- 150 MHz e200z4 Power Architecture®core
- Variable length instruction encoding (VLE)
- Superscalar architecture with 2 execution units
- Up to 2 integer or floating point instructions per cycle
- Up to 4 multiply and accumulate operations per cycle
- Memory organization
- 2 MB on-chip flash memory with ECC and read-while-write (RWW)
- 128 KB on-chip SRAM with standby functionality (32 KB) and ECC
- 8 KB instruction cache (with line locking), configurable as 2- or 4-way
- 14 + 3 KB eTPU code and data RAM
- 4 x 4 crossbar switch (XBAR)
- 24-entry MMU
- Fail Safe Protection
- 16-entry Memory Protection Unit (MPU)
- CRC unit with 3 submodules
- Junction temperature sensor
- Interrupt
- Configurable interrupt controller (INTC) with non-maskable interrupt (NMI)
- 64-channel eDMA
- Serial channels
- 3 eSCI modules
- 3 DSPI modules (2 of which support downstream Micro Second Channel [MSC])
- 3 FlexCAN modules with 64 message buffers each
- 1 FlexRay module (V2.1) up to 10 Mbit/s w/dual or single channel, 128 message objects, ECC
- 1 eMIOS (24 unified channels)
- 1 eTPU2 (second generation eTPU)
- 32 standard channels
- 1 reaction module (6 channels with 3 outputs per channel)
- 2 enhanced queued analog-to-digital converters (eQADCs)
- Forty 12-bit input channels
- 688 ns minimum conversion time
- On-chip CAN/SCI Bootstrap loader with Boot Assist Module (BAM)
- Nexus: Class 3+ for core; Class 1 for eTPU
- JTAG (5-pin)
- Development Trigger Semaphore (DTS)
- Clock generation
- On-chip 4-40 MHz main oscillator
- On-chip FMPLL (frequency-modulated phase-locked loop)
- Up to 112 general purpose I/O lines
- Power reduction modes: slow, stop, and standby
- Flexible supply scheme
- 5 V single supply with external ballast
- Multiple external supply: 5 V, 3.3 V , and 1.2 V
- Designed for LQFP176, LBGA208, PBGA324
- 150 MHz e200z4 Power Architecture®core
样片和购买
| 产品型号 | 供货状态 | 包装类型 | CPU Clock Frequency (MHz) (max) | Flash Size (kB) (Data) | Features set | 温度（ºC） | 预算价格(US$) | 数量 | ECCN (US) | Country of Origin | 更多信息 | 从分销商订购 | 从ST订购 | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| min | max | |||||||||||||
| SPC564A70L7COBR | 批量生产 | Tape And Reel | 120 | - | - | -40 | 125 | 10.5 | 1000 | 5A991B4A | MALTA | 查看供货情况 | ||
| SPC564A70L7COBY | 批量生产 | Tray | 120 | - | - | -40 | 125 | 10.5 | 1000 | 5A991B4A | MALTA | 没有经销商，请联系我们的销售办事处 | ||
| SPC564A70L7CFAR | 批量生产 | Tape And Reel | 150 | - | Flexray | -40 | 125 | 11.5 | 1000 | 5A991B4A | MALTA | 查看供货情况 | ||
| SPC564A70L7CFBR | 批量生产 | Tape And Reel | 120 | - | Flexray | -40 | 125 | 10.5 | 1000 | 5A991B4A | MALTA | 查看供货情况 | ||
| SPC564A70L7CFBY | 批量生产 | Tray | 120 | - | Flexray | -40 | 125 | 10.5 | 1000 | 5A991B4A | MALTA | 没有经销商，请联系我们的销售办事处 | ||
| SPC564A70L7CFAY | 批量生产 | Tray | 150 | - | - | -40 | 125 | 11.5 | 1000 | 5A991B4A | MALTA | 没有经销商，请联系我们的销售办事处 | ||
SPC564A70L7COBR
供货状态
批⁠量⁠生⁠产包装类型
Tape And Reel单价(US$)
10.5*SPC564A70L7COBY
供货状态
批⁠量⁠生⁠产包装类型
Tray单价(US$)
10.5*SPC564A70L7CFAR
供货状态
批⁠量⁠生⁠产包装类型
Tape And Reel单价(US$)
11.5*SPC564A70L7CFBR
供货状态
批⁠量⁠生⁠产包装类型
Tape And Reel单价(US$)
10.5*SPC564A70L7CFBY
供货状态
批⁠量⁠生⁠产包装类型
Tray单价(US$)
10.5*SPC564A70L7CFAY
供货状态
批⁠量⁠生⁠产包装类型
Tray单价(US$)
11.5*精选 视频
First Automotive MCUs introducing Phase Change Memory (PCM)
设计工具
开发工具硬件
-
-
Picture 产品型号 制造商 描述 CYCLONE P&E Microcomputer Systems Automated, Stand-Alone Production Programmer, Debug & Test. CYCLONE FX P&E Microcomputer Systems Automated, Stand-Alone Production Programmer, Debug & Test. DCI-GSI2 dSPACE dSPACE DCI-GSI2 is a low latency and high bandwidth on-chip debug interface for bypassing, calibration, measurement and flash programming. Multilink Universal P&E Microcomputer Systems Debug Probe for ARM and other devices. Multilink Universal FX for SPC5 P&E Microcomputer Systems High-Speed Debug Probe for ARM and other devices. PowerDebug JTAG Debugger Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. 
SPC5-CONNECT ST Programmable interface for PC communication to automotive target systems. 
SPC5-UDESTK ST USB/JTAG debugger for SPC5 MCUs with software license included (by PLS) SPC564A70CAL176 ST Calibration system for SPC564A series devices (Andorra 2) MB devices TRACE32 PowerTools Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. UDE/UAD2next for SPC5 PLS UDE/UAD2next for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. UDE/UAD2pro for SPC5 PLS UDE/UAD2pro for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. UDE/UAD3+ for SPC5 PLS UDE/UAD3+ for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. XETK calibration interface ETAS The Ethernet-based ETK, FETK and XETK interfaces provide direct access to the control variables and parameters of an ECU via the parallel data and address bus, or via a serial microcontroller testing or debugging interface. iC5000 On-chip Analyzer iSYSTEM iC5000 belongs to iSYSTEM's premium embedded development tool family for single and multi-core development and testing. iC5700 On-chip Analyzer iSYSTEM iC5700 is iSYSTEM's premium embedded development tool for complex single and multi-core development. iC6000 On-chip Analyzer with Aurora protocol support iSYSTEM iC6000 is iSYSTEM's premium embedded development solution supporting microcontrollers featuring the Aurora physical interface. 产品型号Automated, Stand-Alone Production Programmer, Debug & Test.
Automated, Stand-Alone Production Programmer, Debug & Test.
dSPACE DCI-GSI2 is a low latency and high bandwidth on-chip debug interface for bypassing, calibration, measurement and flash programming.
Debug Probe for ARM and other devices.
High-Speed Debug Probe for ARM and other devices.
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
Programmable interface for PC communication to automotive target systems.
USB/JTAG debugger for SPC5 MCUs with software license included (by PLS)
Calibration system for SPC564A series devices (Andorra 2) MB devices
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
UDE/UAD2next for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
UDE/UAD2pro for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
UDE/UAD3+ for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
The Ethernet-based ETK, FETK and XETK interfaces provide direct access to the control variables and parameters of an ECU via the parallel data and address bus, or via a serial microcontroller testing or debugging interface.
iC5000 belongs to iSYSTEM's premium embedded development tool family for single and multi-core development and testing.
iC5700 is iSYSTEM's premium embedded development tool for complex single and multi-core development.
iC6000 is iSYSTEM's premium embedded development solution supporting microcontrollers featuring the Aurora physical interface.
-
-
-
Picture 产品型号 制造商 描述 ASH/ETEC Ash Ware ETEC C Compiler Toolkit ASH/ETPU Ash Ware ETPU/ETPU2 Development Kit Arctic Studio - Development Tools ARCCORE AUTOSAR and embedded SW configuration. BYTE/eTPU Byte Craft eTPU_C Code Development System Diab Compiler Wind River The Proven Development Tool for Automotive Safety. EB tresos Studio - Development Tools Elektrobit AUTOSAR and embedded SW configuration. ECU Interface Software dSPACE dSPACE ECU Interface Software prepares ECUs, RCP Hardware and HIL Simulators for ECU Interfacing like bypassing, calibration, measurement and testing. ICDPPCNEXUS P&E Microcomputer Systems In-circuit debug software for SPC5 and similar devices. MULTI Integrated Development Environment Green Hills Software MULTI Integrated Development Environment MULTISPC56 Green Hills Software MULTI IDE PROGPPCNEXUS P&E Microcomputer Systems Flash programming software for SPC5 and similar devices. PowerView Debugger IDE Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. SPC5-STUDIO ST Code Generator, Quick resources configurator and Eclipse development environment for SPC5 MCUs SPC5-UDEDEBG ST PLS JTAG debugger software full license or license renewal TargetLink dSPACE The production code generator dSPACE TargetLink generates highly efficient C code straight from MATLAB®/Simulink®/Stateflow®. UNITPPCNEXUS P&E Microcomputer Systems Interface library for SPC5-compatible PEmicro interfaces. WIND-WORKBENCH Wind River Wind River Workbench WinIDEASPC56 iSYSTEM winIDEA IDE isystem.connect iSYSTEM Automate your testing or other embedded debugging activitites with iSYSTEM's SDK. testIDEA iSYSTEM iSYSTEM's testing tools supporting original binary code testing on target together with their BlueBox™ On-Chip Analysers and iTAG Debuggers. winIDEA Open iSYSTEM iSYSTEM's integrated development environment (IDE) supporting its range of iTAG Debuggers for Cortex-M microcontrollers. 产品型号ETEC C Compiler Toolkit
ETPU/ETPU2 Development Kit
AUTOSAR and embedded SW configuration.
eTPU_C Code Development System
The Proven Development Tool for Automotive Safety.
AUTOSAR and embedded SW configuration.
dSPACE ECU Interface Software prepares ECUs, RCP Hardware and HIL Simulators for ECU Interfacing like bypassing, calibration, measurement and testing.
In-circuit debug software for SPC5 and similar devices.
MULTI Integrated Development Environment
MULTI IDE
Flash programming software for SPC5 and similar devices.
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
Code Generator, Quick resources configurator and Eclipse development environment for SPC5 MCUs
PLS JTAG debugger software full license or license renewal
The production code generator dSPACE TargetLink generates highly efficient C code straight from MATLAB®/Simulink®/Stateflow®.
Interface library for SPC5-compatible PEmicro interfaces.
Wind River Workbench
winIDEA IDE
Automate your testing or other embedded debugging activitites with iSYSTEM's SDK.
iSYSTEM's testing tools supporting original binary code testing on target together with their BlueBox™ On-Chip Analysers and iTAG Debuggers.
iSYSTEM's integrated development environment (IDE) supporting its range of iTAG Debuggers for Cortex-M microcontrollers.
-
软件
评估工具
-
-
Picture 产品型号 制造商 描述 
SPC56A-Discovery ST Discovery Plus Kit for SPC56 A line - with SPC564A70L7 MCU 产品型号Discovery Plus Kit for SPC56 A line - with SPC564A70L7 MCU
-
支持和应用
| 产品型号 | 供货状态 | 封装 | 等级规格 | 符合RoHS级别 | 材料声明** |
|---|---|---|---|---|---|
| SPC564A70L7CFAR | 批量生产 | LQFP 176 24x24x1.4 | Automotive | Ecopack2 | |
| SPC564A70L7CFAY | 批量生产 | LQFP 176 24x24x1.4 | Automotive | Ecopack2 | |
| SPC564A70L7CFBR | 批量生产 | LQFP 176 24x24x1.4 | Automotive | Ecopack2 | |
| SPC564A70L7CFBY | 批量生产 | LQFP 176 24x24x1.4 | Automotive | Ecopack2 | |
| SPC564A70L7COBR | 批量生产 | LQFP 176 24x24x1.4 | Automotive | Ecopack2 | |
| SPC564A70L7COBY | 批量生产 | LQFP 176 24x24x1.4 | Automotive | Ecopack2 |
SPC564A70L7CFAR
Package:
LQFP 176 24x24x1.4Material Declaration**:
PDFSPC564A70L7CFAY
Package:
LQFP 176 24x24x1.4Material Declaration**:
PDFSPC564A70L7CFBR
Package:
LQFP 176 24x24x1.4Material Declaration**:
PDFSPC564A70L7CFBY
Package:
LQFP 176 24x24x1.4Material Declaration**:
PDFSPC564A70L7COBR
Package:
LQFP 176 24x24x1.4Material Declaration**:
PDFSPC564A70L7COBY
Package:
LQFP 176 24x24x1.4Material Declaration**:
PDF(**) st.com上提供的材料声明表单可能是基于包装系列中最常用的封装的通用文档。因此，它们可能不是100%适用于特定的设备。有关特定设备的信息，请联系 销售支持 。
