-
This family of MCUs targets automotive powertrain controller applications for four-cylinder gasoline and diesel engines, chassis control applications, transmission control applications, steering and braking applications, as well as low-end hybrid applications.
Many of the applications are considered to be functionally safe and the family is designed to achieve ISO26262 ASIL-D compliance.
主要特性
- Two main 32-bit Power Architecture® VLE compliant CPU core (e200z4), dual issue, running in lockstep
- Single-precision floating point operations
- 16 KB local instruction SRAM and 64 KB local data SRAM
- 4 KB I-Cache and 2 KB D-Cache
- One 32-bit Power Architecture® VLE compliant I/O processor core (e200z2)
- Single-precision floating point operations
- Lightweight Signal Processing Auxiliary Processing Unit (LSP APU) instruction support for digital signal processing (DSP)
- 16 KB local instruction SRAM and 48 KB local data SRAM
- 2624 KB on-chip flash memory
- Supporting EEPROM emulation (64 KB)
- 64 KB on-chip general-purpose SRAM (+112 KB data RAM included in the CPUs)
- Multi-channel direct memory access controller (eDMA) with 32 channels
- Dual interrupt controller (INTC)
- Dual phase-locked loops, including one Frequency-modulated
- System integration unit lite (SIUL)
- Boot Assist Flash (BAF) supports factory programming using a serial bootload through the asynchronous CAN or LIN/UART
- Generic timer module (GTM122)
- Intelligent complex timer module
- 88 channels (24 input and 64 output)
- 3 programmable fine grain multi-threaded cores
- 26 KB of dedicated SRAM
- Hardware support for engine control, motor control and safety related applications
- Enhanced analog-to-digital converter system with:
- 1 supervisor 12-bit SAR analog converter
- 4 separate fast 12-bit SAR analog converters
- 2 separate 16-bit Sigma-Delta analog converters
- 5 Deserial Serial Peripheral Interface (DSPI) modules
- 5 LIN and UART communication interface (LINFlexD) modules
- 3 MCAN interfaces with advanced shared memory scheme, two supporting ISO CAN-FD and one supporting TTCAN
- One Ethernet controller 10/100 Mbps, compliant IEEE 802.3-2008
- Dual-channel FlexRay controller
- Nexus development interface (NDI) per IEEE-ISTO 5001-2003 standard, with partial support for 2010 standard
- Device and board test support per Joint Test Action Group (JTAG) (IEEE 1149.1)
- Single 5 V +/-10% Power supply supporting cold start conditions (down to 3.0 V)
- Designed for eTQFP144 and eLQFP176
- Two main 32-bit Power Architecture® VLE compliant CPU core (e200z4), dual issue, running in lockstep
精选 视频
First Automotive MCUs introducing Phase Change Memory (PCM)
设计工具
开发工具硬件
-
-
Picture 产品型号 制造商 描述 CYCLONE P&E Microcomputer Systems Automated, Stand-Alone Production Programmer, Debug & Test. CYCLONE FX P&E Microcomputer Systems Automated, Stand-Alone Production Programmer, Debug & Test. DCI-GSI2 dSPACE dSPACE DCI-GSI2 is a low latency and high bandwidth on-chip debug interface for bypassing, calibration, measurement and flash programming. Multilink Universal P&E Microcomputer Systems Debug Probe for ARM and other devices. Multilink Universal FX for SPC5 P&E Microcomputer Systems High-Speed Debug Probe for ARM and other devices. PowerDebug JTAG Debugger Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. 
SPC5-CONNECT ST Programmable interface for PC communication to automotive target systems. 
SPC5-UDESTK ST USB/JTAG debugger for SPC5 MCUs with software license included (by PLS) TRACE32 PowerTools Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. UDE/UAD2next for SPC5 PLS UDE/UAD2next for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. UDE/UAD2pro for SPC5 PLS UDE/UAD2pro for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. UDE/UAD3+ for SPC5 PLS UDE/UAD3+ for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. XETK calibration interface ETAS The Ethernet-based ETK, FETK and XETK interfaces provide direct access to the control variables and parameters of an ECU via the parallel data and address bus, or via a serial microcontroller testing or debugging interface. iC5000 On-chip Analyzer iSYSTEM iC5000 belongs to iSYSTEM's premium embedded development tool family for single and multi-core development and testing. iC5700 On-chip Analyzer iSYSTEM iC5700 is iSYSTEM's premium embedded development tool for complex single and multi-core development. iC6000 On-chip Analyzer with Aurora protocol support iSYSTEM iC6000 is iSYSTEM's premium embedded development solution supporting microcontrollers featuring the Aurora physical interface. 产品型号Automated, Stand-Alone Production Programmer, Debug & Test.
Automated, Stand-Alone Production Programmer, Debug & Test.
dSPACE DCI-GSI2 is a low latency and high bandwidth on-chip debug interface for bypassing, calibration, measurement and flash programming.
Debug Probe for ARM and other devices.
High-Speed Debug Probe for ARM and other devices.
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
Programmable interface for PC communication to automotive target systems.
USB/JTAG debugger for SPC5 MCUs with software license included (by PLS)
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
UDE/UAD2next for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
UDE/UAD2pro for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
UDE/UAD3+ for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
The Ethernet-based ETK, FETK and XETK interfaces provide direct access to the control variables and parameters of an ECU via the parallel data and address bus, or via a serial microcontroller testing or debugging interface.
iC5000 belongs to iSYSTEM's premium embedded development tool family for single and multi-core development and testing.
iC5700 is iSYSTEM's premium embedded development tool for complex single and multi-core development.
iC6000 is iSYSTEM's premium embedded development solution supporting microcontrollers featuring the Aurora physical interface.
-
-
-
Picture 产品型号 制造商 描述 ASH/ETEC Ash Ware ETEC C Compiler Toolkit ASH/ETPU Ash Ware ETPU/ETPU2 Development Kit Arctic Studio - Development Tools ARCCORE AUTOSAR and embedded SW configuration. BYTE/eTPU Byte Craft eTPU_C Code Development System Diab Compiler Wind River The Proven Development Tool for Automotive Safety. EB tresos Studio - Development Tools Elektrobit AUTOSAR and embedded SW configuration. ECU Interface Software dSPACE dSPACE ECU Interface Software prepares ECUs, RCP Hardware and HIL Simulators for ECU Interfacing like bypassing, calibration, measurement and testing. ICDPPCNEXUS P&E Microcomputer Systems In-circuit debug software for SPC5 and similar devices. MULTI Integrated Development Environment Green Hills Software MULTI Integrated Development Environment MULTISPC56 Green Hills Software MULTI IDE PROGPPCNEXUS P&E Microcomputer Systems Flash programming software for SPC5 and similar devices. PowerView Debugger IDE Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. SPC5-STUDIO ST Code Generator, Quick resources configurator and Eclipse development environment for SPC5 MCUs SPC5-UDEDEBG ST PLS JTAG debugger software full license or license renewal TargetLink dSPACE The production code generator dSPACE TargetLink generates highly efficient C code straight from MATLAB®/Simulink®/Stateflow®. UNITPPCNEXUS P&E Microcomputer Systems Interface library for SPC5-compatible PEmicro interfaces. WIND-WORKBENCH Wind River Wind River Workbench WinIDEASPC56 iSYSTEM winIDEA IDE isystem.connect iSYSTEM Automate your testing or other embedded debugging activitites with iSYSTEM's SDK. testIDEA iSYSTEM iSYSTEM's testing tools supporting original binary code testing on target together with their BlueBox™ On-Chip Analysers and iTAG Debuggers. winIDEA Open iSYSTEM iSYSTEM's integrated development environment (IDE) supporting its range of iTAG Debuggers for Cortex-M microcontrollers. 产品型号ETEC C Compiler Toolkit
ETPU/ETPU2 Development Kit
AUTOSAR and embedded SW configuration.
eTPU_C Code Development System
The Proven Development Tool for Automotive Safety.
AUTOSAR and embedded SW configuration.
dSPACE ECU Interface Software prepares ECUs, RCP Hardware and HIL Simulators for ECU Interfacing like bypassing, calibration, measurement and testing.
In-circuit debug software for SPC5 and similar devices.
MULTI Integrated Development Environment
MULTI IDE
Flash programming software for SPC5 and similar devices.
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
Code Generator, Quick resources configurator and Eclipse development environment for SPC5 MCUs
PLS JTAG debugger software full license or license renewal
The production code generator dSPACE TargetLink generates highly efficient C code straight from MATLAB®/Simulink®/Stateflow®.
Interface library for SPC5-compatible PEmicro interfaces.
Wind River Workbench
winIDEA IDE
Automate your testing or other embedded debugging activitites with iSYSTEM's SDK.
iSYSTEM's testing tools supporting original binary code testing on target together with their BlueBox™ On-Chip Analysers and iTAG Debuggers.
iSYSTEM's integrated development environment (IDE) supporting its range of iTAG Debuggers for Cortex-M microcontrollers.
-
