AEK-POW-SPSB081

批量生产
Design Win

Automotive power management IC evaluation board with LIN and CAN-FD

下载数据摘要 Order Direct

产品概述

描述

The AEK-POW-SPSB081 is a power management IC evaluation board with enhanced power management functionalities, such as various standby modes to minimize power consumption with programmable local and remote wake-up capability.

The board is based on the SPSB081 power management system IC, which embeds one low-drop voltage regulator (V1) to supply the system microcontroller and another voltage regulator (V2) to be used as a voltage tracker of V1 or to supply external peripheral loads such as sensors.

V1 has a fixed rail of 5 V and features an overvoltage detection and protection solution, while V2 can work in two different ways: as a voltage tracker of V1, or as an independent voltage regulator programmable via SPI with 5 or 3.3 V.

Four high-side drivers allow supplying and driving LEDs and sensors. These high-side drivers are driven via SPI and can be configured in four different modes: OFF, ON, TIMED (with programmable time), and PWM (configurable via device registers).

Moreover, you can set the high-side driver output to be driven by the DIR pin. This functionality allows the user to generate custom PWM signals for the high-side outputs.

All outputs are short-circuit protected and detect open-load.

The communication protocol used to configure SPSB0815 registers is the SPI, implemented with four wires (MISO, MOSI, CSN, and CLK).

The AEK-POW-SPSB081 also exploits the LIN and CAN transceivers embedded in the IC, allowing the use of the board as a bridge between the microcontroller and the CAN or LIN communication lines.

An external microcontroller (for example, when using an AEK-MCU-C1MLIT1) has to refresh periodically a watchdog TRIG bit in the SPSB081 register via SPI, to maintain the device in active mode.

In case of watchdog failure, the device enters the V1_standby (for energy saving). To wake it up, send a pulse to the WU1_IN pin or just press the S1 button.

By placing a jumper on JP1, the device enters the debug mode where the watchdog is inactive.

Three demos are available in the AutoDevKit ecosystem, each of them based on a different SPC58 microcontroller evaluation board plus an AEK-POW-SPSB081.

The demos show how to use the outputs, configuring them in four different modes: OUT 1 for ON, OUT 2 for TIMED, OUT 3 for PWM and OUT 4 for DIR.

V2 is configured as a linear regulator and changes settings alternatively every 2.5 seconds between 3.3 and 5 V.

CAN connector and CAN_rx/CAN_tx pins are then connected to the microcontroller board.

The CAN test signals transmitted from the microcontroller every five seconds can be effectively decoded through CAN_H/CAN_L pins.

  • 所有功能

    • SPSB0815 power management IC is AEC-Q100 qualified
    • One 5 V low drop voltage regulator (V1) for the microcontroller and peripheral supply, with a current regulation of 250 mA maximum
    • One configurable via SPI low drop voltage regulator (V2) for 5 or 3.3 V, also used as tracker for V1, and with off-board protection, with a current limitation of 100 mA maximum
    • Configurable window watchdog from microcontroller
    • Debug mode available with watchdog disablement
    • ISO 17987-4/2016 compliant LIN transceiver
    • ISO 11898-2/2016 and SAE J2284 compliant CAN-FD transceiver with local failure and bus failure diagnosis
    • 4 high-side drivers (0.14 A, RON = 7 Ω) configurable in four different modes (OFF, ON, TIMED, and PWM) suitable to drive external LED modules or supply external contacts
    • WU1 wake-up pin with programmable cyclic sense functionality
    • DIR pin to drive HS outputs (OUT 1 to OUT 4) manually
    • Programmable periodic system wake-up feature
    • DIAGN output pin to notify system error conditions
    • Current monitoring for all internal high-side drivers
    • Open-load diagnosis for all outputs
    • V1 overvoltage detection and protection
    • Device temperature warning and protection

您可能还会喜欢...

All tools & software

    • 产品型号
      状态
      描述
      类型
      供应商

      STSW-AUTODEVKIT

      批量生产

      AutoDevKit Studio for 32-bit power architecture MCUs

      评估工具软件 ST
      STSW-AUTODEVKIT

      描述:

      AutoDevKit Studio for 32-bit power architecture MCUs
    • 产品型号
      状态
      描述
      类型
      供应商

      SPC5-STUDIO

      批量生产

      SPC5 MCU的代码生成器、快速资源配置器和Eclipse开发环境

      SPC5软件开发工具 ST
      SPC5-STUDIO

      描述:

      SPC5 MCU的代码生成器、快速资源配置器和Eclipse开发环境

质量与可靠性

产品型号 Marketing Status 等级规格 符合RoHS级别 WEEE Compliant 材料声明**
AEK-POW-SPSB081
批量生产
CARD 工业 Ecopack2 Yes

AEK-POW-SPSB081

Package:

CARD

Material Declaration**:

Marketing Status

批量生产

Package

CARD

Grade

Industrial

RoHS Compliance Grade

Ecopack2

(**) st.com上提供的材料声明表单可能是基于包装系列中最常用的封装的通用文档。因此,它们可能不是100%适用于特定的设备。有关特定设备的信息,请联系 销售支持

样片和购买

Swipe or click the button to explore more details Don't show this again
产品型号
供货状态
Budgetary Price (US$)*/Qty
从ST订购
Order from distributors
包装类型
RoHS
Country of Origin
ECCN (US)
ECCN (EU)
供应商
核心产品
AEK-POW-SPSB081
Available at distributors

经销商的可用性 AEK-POW-SPSB081

代理商名称
地区 库存 最小订购量 第三方链接

代理商库存报告日期:

无法联系到经销商,请联系我们的销售办事处

AEK-POW-SPSB081 批量生产

Budgetary Price (US$)*/Qty:
-
包:
包装类型:
RoHS:
Country of Origin:
ECCN (US):
ECCN (EU):

产品型号:

AEK-POW-SPSB081

供应商:

ST

核心产品:

SPSB0815-TR

代理商名称

代理商库存报告日期:

Swipe or click the button to explore more details Don't show this again

(*) 建议转售单价(美元)仅用于预算用途。如需以当地货币计价的报价,请联系您当地的 ST销售办事处 或我们的 经销商