产品概述
描述
The ST1S03 is a step-down DC-DC converter optimized for powering a low voltage digital core in HDD applications and, generally, to replace the high current linear solution when the power dissipation may cause a high heating of the application environment. It provides up to 1.5 A over an input voltage range of 3 V to 16 V. A high switching frequency (1.5 MHz) allows the use of tiny surface-mount components: as well as the resistor divider to set the output voltage value, only an inductor, a Schottky diode and two capacitors are required. Besides, a low output ripple is guaranteed by the current mode PWM topology and by the use of low ESR SMD ceramic capacitors. The device is thermal protected and current limited to prevent damages due to an accidental short-circuit. The ST1S03 device is available in a DFN6D package.
-
所有功能
- Step-down current mode PWM (1.5 MHz) DC-DC converter
- 2% DC output voltage tolerance
- Internal soft-start for STARTUP current limitation and power on delay of 50 - 100 μs
- Typical efficiency: > 70% over all operating conditions
- 1.5 A output current capability
- Not switching quiescent current: max 2.5 mA over temperature range
- Switch VDS: max. 350 mV at ISW= 750 mA
- Uses tiny capacitors and inductors
- Available in DFN6D 3 x 3 mm package with exposed pad
电路原理图
eDesignSuite
eDesignSuite is a comprehensive set of easy-to-use design-aid utilities ready to help you streamline the system development process with a wide range of ST products.
Power Management Design Center
Thermal-electrical Simulators for Components
Signal Conditioning Design Tool
NFC/RFID Calculators
Power Supply Design Tool
SMPS design, by topology, by type and by product PFC design with analog and digitial control Supports various PCB configurations 
LED Lighting Design Tool
Handles AC-DC and DC-DC design in common topologies Displays interactive and annotated schematic Provides current/voltage graphs, Bode plots, efficiency curves and power-loss data 
Digital Power Workbench
Provides a step-by-step optimized design of power section and control loop Generates the STM32Cube embedded software package for custom applications and allows firmware project generation, compatible with multiple STM32 IDEs 
Power Tree Designer
Specify input/output power for each node in the tree Check for consistency Design each individual node 
AC Switches Simulator
Select ratings and application waveforms Get junction temperature and blocking voltage graphs Search and sort suitable devices 
Rectifier Diodes Simulator
Select ratings and application waveforms Estimate power losses Search and sort suitable devices 
STPOWER Studio
Supports long mission profiles Provides power loss and temperature graphs Helps define heatsink thermal properties 
Twister Sim
Help select the right ViPOWER Automotive power device Supports load-compatibility, wiring harness optimization, fault condition impact and diagnostic analysis Supports various PCB configurations 
TVS Simulator
Specify system ratings and surge waveform Search and sort suitable devices 
Active Filters
Handles multi-stage-designs and common topologies Returns circuit component values Provides gain, phase and group delay graphs Low Pass, High Pass and Band Pass 
Comparators
Handles most common configurations Returns circuit components values Provides I/O signal waveforms Inverting, Non Inverting, Window 
Low side Current Sensing
Returns circuit component values Provides current error graphs 
High side Current Sensing
Provides current error graphs. Help to select the right High side current sensing and shunt devices. 
NFC Inductance
Input geometry and substrate properties Get antenna impedance 
UHF Link Budget
Enter forward and reverse link characteristics The tool returns link budget estimate 
NFC Tuning Circuit
Enter antenna parameter and matching target Select the topology of the matching network The tool returns component values for the desired design targets 您可能还会喜欢...
特别推荐
EDA符号、封装和3D模型
STMicroelectronics - ST1S03
Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.
Please select one model supplier :
符号
封装
3D模型
样片和购买
| 产品型号 | Order from distributors | 从ST订购 | 供货状态 | ECCN (US) | ECCN (EU) | 包装类型 | 封装 | 温度（ºC） | Country of Origin | Budgetary Price (US$)*/Qty | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 最小值 | 最大值 | |||||||||||
| ST1S03PUR | distributors 无法联系到经销商，请联系我们的销售办事处 | 批量生产 | EAR99 | NEC | Tape and Reel | DFN6 3x3 | 0 | 125 | PHILIPPINES | | ||