产品概述
描述
This SLLIMM (small low-loss intelligent molded module) nano provides a compact, high-performance AC motor drive in a simple, rugged design. It is composed of six IGBTs and three half-bridge HVICs for gate driving, providing low electromagnetic interference (EMI) characteristics with optimized switching speed. The package is optimized for thermal performance and compactness in built-in motor applications, or other low power applications where assembly space is limited. This IPM includes an operational amplifier, completely uncommitted, and a comparator that can be used to design a fast and efficient protection circuit. SLLIMM is a trademark of STMicroelectronics.
-
所有功能
- IPM 3 A, 600 V, 3-phase IGBT inverter bridge including control ICs for gate driving and freewheeling diodes
- Optimized for low electromagnetic interference
- VCE(sat) negative temperature coefficient
- 3.3 V, 5 V, 15 V CMOS/TTL input comparators with hysteresis and pull-down/pull-up resistors
- Undervoltage lockout
- Internal bootstrap diode
- Interlocking function
- Shutdown function
- Comparator for fault protection against overtemperature and overcurrent
- Op-amp for advanced current sensing
- Optimized pinout for board layout
- NTC for temperature control (UL 1434 CA 2 and 4)
eDesignSuite
eDesignSuite is a comprehensive set of easy-to-use design-aid utilities ready to help you streamline the system development process with a wide range of ST products.
Power Management Design Center
Thermal-electrical Simulators for Components
Signal Conditioning Design Tool
NFC/RFID Calculators
Power Supply Design Tool
SMPS design, by topology, by type and by product PFC design with analog and digitial control Supports various PCB configurations 
LED Lighting Design Tool
Handles AC-DC and DC-DC design in common topologies Displays interactive and annotated schematic Provides current/voltage graphs, Bode plots, efficiency curves and power-loss data 
Digital Power Workbench
Provides a step-by-step optimized design of power section and control loop Generates the STM32Cube embedded software package for custom applications and allows firmware project generation, compatible with multiple STM32 IDEs 
Power Tree Designer
Specify input/output power for each node in the tree Check for consistency Design each individual node 
AC Switches Simulator
Select ratings and application waveforms Get junction temperature and blocking voltage graphs Search and sort suitable devices 
Rectifier Diodes Simulator
Select ratings and application waveforms Estimate power losses Search and sort suitable devices 
STPOWER Studio
Supports long mission profiles Provides power loss and temperature graphs Helps define heatsink thermal properties 
Twister Sim
Help select the right ViPOWER Automotive power device Supports load-compatibility, wiring harness optimization, fault condition impact and diagnostic analysis Supports various PCB configurations 
TVS Simulator
Specify system ratings and surge waveform Search and sort suitable devices 
Active Filters
Handles multi-stage-designs and common topologies Returns circuit component values Provides gain, phase and group delay graphs Low Pass, High Pass and Band Pass 
Comparators
Handles most common configurations Returns circuit components values Provides I/O signal waveforms Inverting, Non Inverting, Window 
Low side Current Sensing
Returns circuit component values Provides current error graphs 
High side Current Sensing
Provides current error graphs. Help to select the right High side current sensing and shunt devices. 
NFC Inductance
Input geometry and substrate properties Get antenna impedance 
UHF Link Budget
Enter forward and reverse link characteristics The tool returns link budget estimate 
NFC Tuning Circuit
Enter antenna parameter and matching target Select the topology of the matching network The tool returns component values for the desired design targets EDA符号、封装和3D模型
STMicroelectronics - STGIPN3H60T-H
Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.
Please select one model supplier :
符号
封装
3D模型
质量与可靠性
| 产品型号 | Marketing Status | 封装 | 等级规格 | 符合RoHS级别 | 材料声明** |
|---|---|---|---|---|---|
| STGIPN3H60T-H | 批量生产 | NDIP-26L | 工业 | Ecopack2 | |
STGIPN3H60T-H
Package:
NDIP-26LMaterial Declaration**:
(**) st.com上提供的材料声明表单可能是基于包装系列中最常用的封装的通用文档。因此，它们可能不是100%适用于特定的设备。有关特定设备的信息，请联系 销售支持。
样片和购买
| 产品型号 | Order from distributors | 从ST订购 | 供货状态 | ECCN (US) | ECCN (EU) | 包装类型 | 封装 | 温度（ºC） | Country of Origin | Budgetary Price (US$)*/Qty | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 最小值 | 最大值 | |||||||||||
| STGIPN3H60T-H | distributors 无法联系到经销商，请联系我们的销售办事处 | 批量生产 | EAR99 | NEC | Tube | NDIP-26L | - | - | CHINA | | ||