STHVUP32

批量生产
Design Win Education

32通道±100 V、±0.4/0.8 A、3/5 电平 RTZ、TR 开关、带集成发射波束成形器的高速超声脉冲发生器

下载数据摘要

产品概述

描述

The STHVUP32 is a 32 channels monolithic high-voltage and high-speed pulser with an integrated beam-former. It is specifically designed for pulse generation in multi-channel low power ultra-portable medical ultrasound applications.

The waveforms generated by STHVUP32 are described with sequences of up to 32 states stored in the device memory. With each state it is possible to configure each individual output channel to be connected to high voltage supplies (positive or negative), clamped to ground or left in high impedance. 

A pure analog section provides each channel four half-bridges (four high-voltage P-channel and four high-voltage N-channel MOSFETs), a clamping-to-ground circuit and a transmitting/receiving switch structure which guarantees an effective isolation during the transmission phase. Each channel features also integrated high-voltage level translators and noise-blocking diodes.

Through a dedicated bit, channels can be programmed as a 3-level output or as a 5-level output. In 3-level mode, the four half-bridges are driven in parallel to provide a default peak current of 800 mA. However, it is also possible to program a low-consumption and low output current modes to decrease the overall power consumption: in this case, it is possible to use only one, two or three half-bridges, therefore the peak current can be reduced to 200, 400 or 600 mA respectively. In 5-level mode, the four half-bridges can be driven independently, and each half-bridge has a current capability of 200 mA. The clamp circuit, used to force the XDCR<31:0> output pins down to ground, has a resistance of 23 Ω and a peak current capability of 0.64 A. The 32 independent T/R switches can be used in a multiplexing configuration.

The STHVUP32 also includes some global blocks: thermal protection circuits, undervoltage checks on VDDP3V3, VDDM3V3 and DVDD, a power-on-reset (POR) on DVDD and a global self-biased supply for the drivers of the high-voltage MOSFET.

All functions are managed by a digital core working at a maximum clock frequency of 200 MHz. This block manages the delay profiles used in the beamformer, the waveform generation and the various global settings and grants that all the device operations are performed in the correct sequence.

  • 所有功能

    • Pulsed wave (PW) and continuous wave (CW) mode operations:
      • 3- or 5-level ±100 V output waveform
      • Programmable ±200 mA or ±400 mA or ±600 mA or ±800 mA source and sink current in 3-level configuration (±400 mA or ±200 mA in 5-level configuration)
    • Fully integrated 23 Ω resistance real clamping-to-ground function
    • Fully integrated 23 Ω resistance transmitting/receiving switches (TR_SW)
      • Compliant with receiver multiplexing function
    • Auxiliary integrated circuits
      • Noise-blocking diodes
      • Thermal protection
      • Undervoltage protection and bias supply checks
    • Programmable power management to optimize the performances for ultra-portable applications
    • Beamforming in transmission mode
      • Programmable single-channel delay for beam steering and focusing
      • Clock frequency up to 200 MHz
      • 5 ns delay resolution
      • From 5 ns to 20 us delay range @ 200 MHz
      • 3 us minimum delay table writing time
    • Embedded memory to store transmission patterns
      • 32 states for waveform definition, with waveform compression algorithm
      • Up to 4 different waveforms for each channel
    • Easy driving control
      • Control through standard Quad Serial Peripheral Interface (QSPI)
      • Few input signals to drive several devices
      • Single interrupt as alert signal
      • Single trigger to manage transmitting (TX) and receiving (RX) phases, fully automatic and programmable
      • Anti-glitch on TRIGGER signal during TX phase
    • Checksum control
    • Very low package thermal resistance
    • Latch-up free due to HV SOI technology
    • Just a few passive components needed
    • Small package: BGA 11.5 mm x 10.5 mm x 1.35 mm with 168 balls and 0.8 mm pitch

EDA符号、封装和3D模型

STMicroelectronics - STHVUP32

Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.

Please select one model supplier :

Symbols

符号

Footprints

封装

3D model

3D模型

质量与可靠性

产品型号 Marketing Status 等级规格 符合RoHS级别 材料声明**
STHVUP32
批量生产
FCBGA168 11.5X10.5X1.35 0.8P 工业 Ecopack2

STHVUP32

Package:

FCBGA168 11.5X10.5X1.35 0.8P

Material Declaration**:

PDF XML

Marketing Status

批量生产

Package

FCBGA168 11.5X10.5X1.35 0.8P

Grade

Industrial

RoHS Compliance Grade

Ecopack2

(**) st.com上提供的材料声明表单可能是基于包装系列中最常用的封装的通用文档。因此,它们可能不是100%适用于特定的设备。有关特定设备的信息,请联系 销售支持

样片和购买

Swipe or click the button to explore more details Don't show this again
产品型号
供货状态
Budgetary Price (US$)*/Qty
从ST订购
Order from distributors
包装类型
RoHS
Country of Origin
ECCN (US)
ECCN (EU)
STHVUP32
Available at distributors

经销商的可用性 STHVUP32

代理商名称
地区 库存 最小订购量 第三方链接

代理商库存报告日期:

无法联系到经销商,请联系我们的销售办事处

STHVUP32 批量生产

Budgetary Price (US$)*/Qty:
-
包:
包装类型:
RoHS:
Country of Origin:
ECCN (US):
ECCN (EU):

产品型号:

STHVUP32

Swipe or click the button to explore more details Don't show this again

(*) 建议转售单价(美元)仅用于预算用途。如需以当地货币计价的报价,请联系您当地的 ST销售办事处 或我们的 经销商