STEVAL-MKI125V1 A3G4250D adapter board for standard DIL 24 socket Quick view
主な特徴
Complete A3G4250D pinout for a standard DIL 24 socket Fully compatible with the STEVAL-MKI109V2 motherboard RoHS compliant さらに表示
画像
SPC5-UDEDEBG PLS JTAG debugger software full license or license renewal Quick view
主な特徴
Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board. Supports SPC5x MCUs Supports Multicore, eTPU and GTM debugging Includes FLASH programming capability Support service provided through STMicroelectronics さらに表示
SPC56B-Discovery Discovery Kit for SPC56 B line - with SPC560B54L5 MCU Quick view
主な特徴
SPC560B54L5 32-bit 48 MHz e200z0h CPU, 32-bit Power Architecture® Technology CPU, 768 kB Code Flash in an LQFP144 package. On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers. Board power supply: through external +12 V PSU or from the USB bus (5 V supply voltage). Seven LEDs: D6 for 5 V power on,D2 for Reset, D101, D102, D103 for PLS debugger section, D7 and D8 for PC3 and PC2 outputs Two push buttons (reset and user) A potentiometers for ADC input (user) Two extension headers (2 x 36 pin - 100 mil) for all LQFP144 pins and for quick connection to prototyping boards, additional modules and easy probing. JTAG interface (2 x 7 male 100mil connector) USB port (mini -B) 16 MHz crystal Specification: Board size 100 x 65 mm MCU: SPC560B54L5 - LQFP144 2 extension headers 2 x 36 pin - 100 mil DC connector (+12 V input) Mini USB - B JTAG 2 x 7 - 100 mil connector さらに表示
画像
EV-VN7010AJ VN7010AJ Evaluation Board Quick view
主な特徴
Simple single IC application board dedicated for VN7010AJ Provides electrical connectivity and thermal heat-sinking for easy prototyping General device features Single channel smart high-side driver with MultiSense analog feedback Very low standby current Compatible with 3 V and 5 V CMOS outputs Diagnostic functions Multiplexed analog feedback of: load current with high precision proportional current mirror, VCC supply voltage and TCHIP device temperature Overload and short to ground (power limitation) indication Thermal shutdown indication OFF-state open-load detection Output short to VCC detection Sense enable/disable Protections Undervoltage shutdown Overvoltage clamp Load current limitation Self limiting of fast thermal transients Configurable latch-off on overtemperature or power limitation with dedicated fault reset pin Loss of ground and loss of VCC Reverse battery with external components Electrostatic discharge protection さらに表示
SAMPLES-AUTOPMIC Automotive Voltage Regulators & System Basis Chip Evaluation Tool Quick view
主な特徴
Immediate evaluation of Voltage Regulators, Power Management and Multichannel Power Management with a selection of samples. The kit includes さらに表示
EV-VNH7100BAS VNH7100BAS Evaluation board Quick view
主な特徴
Simple single IC application board dedicated for VNH7100BAS Provides electrical connectivity and thermal heat-sinking for easy prototyping さらに表示
L99LD21-ADIS Led Driver DISCOVERY Quick view
主な特徴
2 soldered L99LD21 flexible LED drivers Board size 100 x 55 mm Two extension headers (2 x 36 pin - 100 mil) for quick connection to SPC560B-DIS discovery board Controllable by dedicated GUI available on www.st.com Free ready to run application firmware available on www.st.com, to support quick evaluation and development さらに表示
AEK-MOT-SM81M1 Stepper motor driver evaluation board based on the L99SM81V for automotive applications Quick view
主な特徴
Board functionality based on L99SM81V programmable stepper motor driver for automotive applications: with micro-stepping and hold functions BEMF monitoring for stall detection programmable configuration via SPI 5 V internal linear voltage regulator (output available on board connector) Board reverse battery protection with STD95N4F3 MOSFET, which can be substituted with two optionally mounted diodes and a jumper Input operating voltage range from 6 V to 28 V Output current up to 1.35 A Board size: 65 mm length x 81 mm width x 11 mm maximum component height WEEE and RoHS compliant All ST components are qualified Automotive grade Part of the AutoDevKit™ initiative Applications: automotive bipolar stepper motor さらに表示
画像
AEK-LED-21DISM1 Digitally controlled LED driver board for automotive lighting applications Quick view
主な特徴
Two embedded L99LD21 high power LED drivers able to supply four independent channels Output current up to 1.69 A each channel Input operating voltage range from 5.5 V to 24 V Programmable via SPI, allowing accurate LED current setting Protections and diagnostics for output short-circuit and open-load, overtemperature, and battery undervoltage. Automotive Limp-Home Mode support Board size: 81 x 100 mm. Maximum components height: 11 mm WEEE and RoHS compliant All ST components are qualified Automotive grade Board designed according to the AutoDevKit initiative さらに表示
画像
AEK-CON-AFLVIP2 Adaptive front lighting connector board with VIPower board slot Quick view
主な特徴
Designed to connect the following elements for a complete automatic front lighting (AFL) adjustment solution for a LED vehicle headlight: An MCU board such as the AEK-MCU-C4MLIT1 with 4x37 connector Two AEK-MOT-SM81M1 stepper motor boards An AEK-LED-21DISM1 LED driver control board with two L99LD21 LED drivers and providing four independent channels An EV-VNx actuator board such as the EV-VN7050AS to switch a headlight colling fan on and off Connected boards are controlled via three separate SPIs Input voltage from 8 VDC to 15 VDC Board size: 65 x 100 mm. Maximum component height: 27 mm Cables included for two stepper motor boards and one LED driver board WEEE and RoHS compliant All ST components are qualified Automotive grade Part of the AutoDevKit initiative さらに表示
画像
STEVAL-MKI109V2 eMotion: ST MEMS adapters motherboard based on STM32F103, compatible with all ST MEMS adapter boards Quick view
主な特徴
Compatible with all available ST MEMS adapter boards Controlled by the STM32F103RET6 high-performance ARM Cortex™ -M3 microcontroller Includes a DIL24 socket for easy MEMS adapter connection 3 V on-board linear voltage regulator DFU compatible for USB microprocessor firmware update USB 2.0 full-speed compliant Debugging connector for SWD/JTAG RoHS compliant さらに表示
画像
STEVAL-MKI110V1 AIS328DQ adapter board for standard DIL24 socket Quick view
主な特徴
Complete AIS328DQ pinout for a standard DIL 24 socket Fully compatible with the STEVAL-MKI109V2 motherboard RoHS compliant さらに表示
画像
SPC58NG-DISP Discovery Kit for SPC58NG - G line Quick view
主な特徴
Featuring SPC58NG84E7, a 32-bit Power Architecture® triple core e200z4, 6MB flash in eLQFP176 package. Device designed to meet ASIL-D safety level and embeds an HSM with 128KB flash memory. 2 Ethernet ports 1 CAN FD port (DB9 connector) JTAG interface (14 pin - 2x7 connector) 2 Push buttons, 4 LEDs for user purposes, reset push button Board Supply: 12 VDC (external power supply) Connector suitable for TFT LCD module Board size 145 x 105 mm さらに表示
画像
SPC58EC-DISP Discovery Kit for SPC58EC - C line Quick view
主な特徴
SPC58EC80E5 is a 32-bit Power Architecture®e200z4d dual core, 4224 kB flash + 128 kB data flash) in eTQFP144. Integrated programmer - debugger. JTAG interface (Standard 7x2 male 100mil). 2 ISO CAN FD port (DB9 connector). 1 Ethernet port. 1 FlexRay, 1 LIN (with transceiver). 1 USB virtual COM Port. Connectors Arduino UNO R3-compatible. 3 Push buttons, 3 LEDs for user purpose. 2 potentiometers for ADC quick evaluation. Reset push button. All GPIOs and signals accessible by a 4x37 0.1" pin grid array allowing connection of the additional boards. 12MHz crystal. Board Supply: 12 VDC (external power supply). Board size 150 x 101 mm. さらに表示
画像
SPC582B-DIS Discovery Kit for SPC582 B line Quick view
主な特徴
SPC582B 32-bit z2 core @80Mhz CPU, 32-bit Power Architecture® Technology CPU, 1MB Code Flash in eQFP64 package. On-board USB-JTAG PLS debugger and dedicated optional connector to plug a stand-alone JTAG debugger. USB Virtual Communication port. Two types of extension resources: Arduino Uno Revision 3 connectivity Extension headers for all device pins and for quick connection to prototyping expansion boards, additional modules and evaluation probing. Flexible board power supply: USB port (mini B - 5V) external sources (DC): 7÷12 V, 5V or 3.3V and 5V Two push buttons: USER and RESET Eight LEDs 3 Integrated Programmer/Debugger 3 LEDs User 1 Reset 1 Power LED: +5V 40MHz Crystal さらに表示
画像
STEVAL-OET003V1 Evaluation board for automotive-grade ESD protection Quick view
主な特徴
Input voltage 5 V 12 V output, step-up converter for transceiver supply voltage LIN transceiver CAN transceiver Automotive-grade ESD protection IEC61000-4-2 compatibility さらに表示
画像
STEVAL-MKI158V1 AIS3624DQ adapter board for a standard DIL24 socket Quick view
主な特徴
Complete AIS3624DQ pin-out for a standard DIL24 socket Fully compatible with STEVAL-MKI109V2 motherboard RoHS compliant さらに表示
画像