冷暖房空調制御

主な特徴

• Simple single IC application board dedicated for VN7003AH
• Provides electrical connectivity and thermal heat-sinking for easy prototyping
• General device features
  • Single channel smart high-side driver with CurrentSense analog feedback
  • Very low standby current
  • Compatible with 3 V and 5 V CMOS outputs
  • Extreme low voltage operation for deep cold cranking applications (compliant with LV124, revision 2013)
• Diagnostic functions
  • Dedicated high precision proportional load current sense
  • Overload and short to ground (power limitation) indication
  • Thermal shutdown indication
  • OFF-state open-load detection
  • Output short to V_CC detection
  • Sense enable/ disable
• Protections
  • Undervoltage shutdown
  • Overvoltage clamp
  • Load current limitation
  • Self limiting of fast thermal transients
  • Loss of ground and loss of VCC
  • Reverse battery
  • Electrostatic discharge protection

Show More

主な特徴

• Input voltage 5 V
• 12 V output, step-up converter for transceiver supply voltage
• LIN transceiver
• CAN transceiver
• Automotive-grade ESD protection
• IEC61000-4-2 compatibility

Show More

主な特徴

• The SPC570S50Ex 32-bit CPU implements two e200z0h processor cores:
  • Core_0 - Main core (80MHz)
  • Core_0s – Checker (safety)
• On-board USB-JTAG PLS debugger and HW selection mode to use it or a third party JTAG debuggers.
• 256 kByte code size limited debugging free of charge evaluation license included.
• Board power supply through the USB bus (5 V supply voltage) or external +12 V PSU.
• User push buttons and LEDs
• Reset button
• 2 potentiometers for ADC evaluation
• Extension headers (4x37 pin - 100 mil) for all device pins and for quick connection to prototyping expansion boards, additional modules and evaluation probing.
• JTAG interface (2x7 male 100mil)
• USB port (mini - B)
• 40 MHz crystal
• Board size 105 x 150mm

Show More

主な特徴

• SPC560P50L5 32-bit 64MHz e200z0h CPU;32-bit Power Architecture^® Technology CPU, 576 KB Flash in an LQFP144 package.
• Shield Connectors (Arduinocompatible).
• On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers (2 x 7 male 100mil connector).
• Free 128 Kbyte code size limited debugging
• Board power supply: from the USB bus (5 V supply voltage) or through external +12 V PSU.
• All GPIOs and DSPI/USB signals accessible by a 4x37 100mil pin grid array allowing connection of an additional boards for dedicated applications.
• CAN, K-LINE, LIN, FlexRay interfaces.
• Main power switch.
• Reset push button.
• 2 potentiometers for ADC evaluation
• 12 MHz crystal.
• Board size 152 x 103 mm

Show More

主な特徴

• SPC560B54L5 32-bit 48 MHz e200z0h CPU, 32-bit Power Architecture® Technology CPU, 768 kB Code Flash in an LQFP144 package.
• On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers.
• Board power supply: through external +12 V PSU or from the USB bus (5 V supply voltage).
• Seven LEDs: D6 for 5 V power on,D2 for Reset, D101, D102, D103 for PLS debugger section, D7 and D8 for PC3 and PC2 outputs
• Two push buttons (reset and user)
• A potentiometers for ADC input (user)
• Two extension headers (2 x 36 pin - 100 mil) for all LQFP144 pins and for quick connection to prototyping boards, additional modules and easy probing.
• JTAG interface (2 x 7 male 100mil connector)
• USB port (mini -B)
• 16 MHz crystal
• Specification:
  • Board size 100 x 65 mm
  • MCU: SPC560B54L5 - LQFP144
  • 2 extension headers 2 x 36 pin - 100 mil
  • DC connector (+12 V input)
  • Mini USB - B
  • JTAG 2 x 7 - 100 mil connector

Show More

主な特徴

• Board Supply: Single 12 VDC external power supply input. Two regulators provide power voltages 5 V and 3.3 V.
• Main power switch and three power supply status LEDs (+12 V, +5 V and +3.3 V)
• All MCU signals accessible by a 37 x 4 100 mil pin grid array allowing connection of an additional board for dedicated applications.
• JTAG interface (7 x 2 male 100 mil connector)
• Two FlexRay channels with jumper enable and DB9 male connector.
• Two CAN channels with jumper enable and DB9 male connector
• K-Line interface.
• Two LIN interfaces (HW configurable)
• Two potentiometers for analog voltage input
• Three user LEDs.
• 40 MHz crystal.
• Reset push button.
• Specification:
  • Board size 115 x 135mm
  • 12 VDC center positive, 2.1 mm inner diameter.

Show More

主な特徴

• Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board.
• Supports SPC5x MCUs
• Supports Multicore, eTPU and GTM debugging
• Includes FLASH programming capability
• Support service provided through STMicroelectronics

Show More

主な特徴

• SPC582B 32-bit z2 core @80Mhz CPU, 32-bit Power Architecture^® Technology CPU, 1MB Code Flash in eQFP64 package.
• On-board USB-JTAG PLS debugger and dedicated optional connector to plug a stand-alone JTAG debugger.
• USB Virtual Communication port.
• Two types of extension resources:
  • Arduino Uno Revision 3 connectivity
  • Extension headers for all device pins and for quick connection to prototyping expansion boards, additional modules and evaluation probing.
• Flexible board power supply:
  • USB port (mini B - 5V)
  • external sources (DC): 7÷12 V, 5V or 3.3V and 5V
• Two push buttons: USER and RESET
• Eight LEDs
  • 3 Integrated Programmer/Debugger
  • 3 LEDs User
  • 1 Reset
  • 1 Power LED: +5V
• 40MHz Crystal

Show More

主な特徴

• Two separated and signal shielded stages: driver & power
• ISO pulse protection (not soldered)
• Reverse polarity protection available on each battery voltage input: Vs, VSREG, power stage
• Current reference comparator
• PCB temperature sensor
• Hall sensors connector and conditioning circuit
• INH_wake-up button
• Microcontroller configured to be supplied by L99ASC03 5V LDO
• Flash mode configurable
• Compatible with external power boards

Show More

主な特徴

• Immediate evaluation of Voltage Regulators, Power Management and Multichannel Power Management with a selection of samples.
• The kit includes
  • 10 samples

Show More