スマート･ウォッチ

主な特徴

• Common features
  • STM32 microcontroller in LQFP64 package
  • 1 user LED shared with Arduino™
  • 1 user and 1 reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External SMPS to generate V_core logic supply
  • 24 MHz HSE
  • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI^® debug connector
  • Arm^® Mbed Enabled™ compliant

さらに表示

主な特徴

• STM32F439IIH6 High Performance MCU ARM® Cortex™-M4F @ 180 MHz with 256 KB of embedded SRAM
• 8 MB external SRAM
• IMU 9 axes inertial sensor: LSM9DS1
• Environmental sensors: Pressure (LPS25HB), Humidity and Temperature (HTS221), UV index (UVIS25M).
• Proximity and ambient light sensors (2x VL6180X)
• Digital MEMS microphone array (4x MP34DT01)
• USB connector
• Micro SD card expansion
• GPIO expansion for pin control and connection to the STM32Nucleo board thanks to the adapter board included in the package

さらに表示

主な特徴

• Compact solution for wearable, motion sensing applications with a complete set of firmware examples
• iOS and Android apps available
• Main components:
  • STM32L151VEY6 – 32-bit ultra-low-power MCU
  • LSM6DS3 – 3D accelerometer + 3D gyroscope
  • LIS3MDL – 3-axis magnetometer
  • LPS25HB – MEMS pressure sensor
  • BlueNRG-MS – BLE network processor
  • BALF-NRG-01D3 - 50 Ω balun with integrated harmonic filter
  • STNS01 – Li-Ion linear battery charger
  • STC3115 – Fuel gauge IC
• 100 mAh Li-Ion battery included, UN38.3 tested and certified
• Micro USB connector for recharging
• SWD connector for debugging and programming capability
• Watch strap with plastic housing included
• Fully tested and certified by FCC (FCC ID: S9N-WESU1) and IC (IC: 8976C-WESU1)
• RoHS compliant

さらに表示

主な特徴

• VL53L0X ranging and gesture detection expansion board (X-NUCLEO-53L0A1).
  • 4-digit display, displaying the distance of a target from the ranging sensor
  • Accurate absolute ranging distance, independent of the reflectance of the target.
• NUCLEO-F401RE STM32 Nucleo board
• Two VL53L0X satellites
• 0.25, 0.5 and 1mm height spacers to simulate air gaps
• Cover glass
• Two 10 pin connectors for VL53L0X satellite boards
• Equipped with Arduino UNO R3 connector.
• RoHS compliant.
• Basic gesture recognition application can be developed using one or two VL53L0X sensors.
• Two VL53L0X satellite boards can be connected on the X-NUCLEO-53L0A1 expansion board in order to integrate the VL53L0X in customer’s application.
• Full system SW supplied, download from www.st.com/VL53L0X in the folder “Design resources”.

さらに表示

主な特徴

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F401VE high-performance ARM Cortex™ - M4 microcontroller
• Software-adjustable power circuitry to set sensor supply voltage from 0 to 3.6 V
• Includes a DIL24 socket for easy MEMS adapter connection
• Adjustable MEMS DIL24 power supply
• DFU-compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Embedded power monitoring circuitry on sensor supply voltage and current
• Debugging connector for SWD/JTAG
• Can be used with PC software like Unico GUI to manage and analyze MEMS sensor data
• RoHS compliant

さらに表示

主な特徴

• Included in the development kit package:
  • SensorTile module (STEVAL-STLCS01V1) with STM32L476JG, LSM6DSM, LSM303AGR, LPS22HB, MP34DT05-A, BlueNRG-MS, BALF-NRG-02D3 and LD39115J18R
  • SensorTile expansion Cradle board equipped with audio DAC, USB port, STM32 Nucleo, Arduino UNO R3 and SWD connector
  • SensorTile Cradle with battery charger, humidity and temperature sensor, SD memory card slot, USB port and breakaway SWD connector
  • 100 mAh Li-Ion battery
  • Plastic box
  • SWD programming cable
• Software libraries and tools
  • STSW-STLKT01: SensorTile firmware package that supports sensors raw data streaming via USB, data logging on SDCard, audio acquisition and audio streaming.
  • FP-SNS-ALLMEMS1 and FP-SNS-MOTENV1: STM32Cube function packs
  • STBLESensor: iOS and Android demo Apps
  • BlueST-SDK: iOS and Android Software Development Kit
• CE certified
• RoHS and China RoHS compliant
• WEEE compliant
• FCC (ID: S9NSTILE01) certified
• IC (IC: 8976C-STILE01) certified with PMN: STEVAL-STLKT01V1; HVIN: STEVAL-STLCS01V1; HMN: STEVAL-STLCX01V1; FVIN: bluenrg_7_1_e_Mode_2-32MHz-XO32K_4M.img
• TYPE certified (006-000482)

さらに表示

主な特徴

• Very compact module for motion, audio, environmental sensing and Bluetooth^® low energy connectivity with a complete set of firmware examples
• Mobile connectivity via the STBLESensor app, available for iOS™ and Android™
• Main components:
  • STM32L476JG – 32-bit ultra-low-power MCU with Cortex^® M4F
  • LSM6DSM – iNEMO inertial module: 3D accelerometer and 3D gyroscope
  • LSM303AGR – Ultra-compact high-performance eCompass module: ultra-low power 3D accelerometer and 3D magnetometer
  • LPS22HB – MEMS nano pressure sensor: 260-1260 hPa absolute digital output barometer
  • MP34DT05-A – 64 dB SNR digital MEMS microphone
  • BlueNRG-MS – Bluetooth low energy network processor
  • BALF-NRG-02D3 – 50 Ω balun with integrated harmonics filter
  • LD39115J18R – 150 mA low quiescent current low noise LDO 1.8 V
• 2 V - 5.5 V power supply range
• External interfaces: UART, SPI, SAI (serial audio interface), I²C, DFSDM, USB OTG, ADC, GPIOs
• Pluggable or solderable interface
• SWD interface for debugging and programming capability
• CE certified
• RoHS and China RoHS compliant
• WEEE compliant
• FCC certified
• IC certified
• TYPE certified

さらに表示

主な特徴

• LSM6DSL MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±245/±500/±1000/±2000 dps)
• LSM303AGR MEMS 3D accelerometer (±2/±4/±8/±16 g) and MEMS3D magnetometer (±50 gauss)
• LPS22HB MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
• HTS221: capacitive digital relative humidity and temperature
• DIL24 socket for additional MEMS adapters and other sensors
• Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
• I²C sensor hub features on LSM6DSL available
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• RoHS compliant

さらに表示

主な特徴

• Common features
  • STM32 microcontroller in LQFP144 package
  • 3 user LEDs
  • 2 user and reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:SWDST Zio expansion connector including Arduino™ Uno V3ST morpho expansion connector
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External or internal SMPS to generate V_core logic supply
  • Ethernet compliant with IEEE-802.3-2002
  • USB OTG full speed or device only
  • Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45
  • Arm^® Mbed Enabled™ compliant

さらに表示

主な特徴

• Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
• Up to 4-Kbit memory with NDEF support
• 54 mm diameter, single layer circular antenna
• Compatible with STM32 Nucleo boards
• Equipped with Arduino™ UNO R3 connector
• Self-powered or powered through the Arduino™ UNO R3 connectors
• Three general purpose LEDs
• Scalable solution, capable of cascading multiple boards for larger systems
• Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
• FCC and IC verified
• RoHS compliant

さらに表示

主な特徴

• Two ready-to-use printed circuit boards (PCB):
  • ST25DV_Discovery_Mboard:
  • STM32F405VGT6 LQFP100 32-bit microcontroller, with 1 Mbyte Flash memory, 192 + 4 Kbytes SRAM.
  • LCD color screen (320 x 200 pixels)
  • Touch screen driver
  • Different color LEDs (power, user, ST link)
  • User push button
  • Joystick for menu selection
  • リセットボタン
  • On board ST link for microcontroller firmware upgrade and debug
  • ST link mini USB
  • User micro USB
  • USB micro or mini connector for board powering
  • Demonstration use cases stored in memory
  • Demonstration edition (optional add-on module) with Bluetooth Low Energy module, Wi-Fi^® module and JTAG 20 pin connector
• ST25DV_Discovery_ANT_C5:
  • 40 mm x 24 mm, 13.56 MHz inductive antenna etched on the PCB
  • ST25DV04K Dynamic NFC / RFID tag
  • I² C interface connector
  • Energy harvesting output (VOUT) with a 10 nF capacitance filtering circuit
  • GPO configurable as RF WIP/BUSY output, to indicate that an RF operation is ongoing

さらに表示

主な特徴

• On-board NFC card reader IC: ST25R3911B
• 47 mm x 34 mm, four turns, 13.56 MHz inductive antenna etched on PCB and associated tuning circuit
• Six general purpose LEDs
• ISO 18092 (NFCIP-1) active P2P
• ISO 14443A and ISO14443B
• ISO 15693
• FeliCa™
• VHBR
  • 6.8 Mbit/s AFE and PCD to PICC framing
  • 3.4 Mbit/s PICC to PCD framing
• Up to 1.4 W output power with differential antenna
• Possibility of driving two antennas in single ended configuration
• Inductive and capacitive wake-up
• Automatic antenna tuning system
• Transparent and Stream modes to implement MIFARE™ Classic compliant or other custom protocols
• Equipped with Arduino™ UNO R3 connector
• Free comprehensive development firmware library compatible with STM32Cube and samples for ST25R3911B
• Scalable solution for multiple board cascade
• FCC certified
• RoHS compliant

さらに表示

主な特徴

• Common features
  • STM32 microcontroller in LQFP144 package
  • 3 user LEDs
  • 2 user and reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:SWDST Zio expansion connector including Arduino™ Uno V3ST morpho expansion connector
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External or internal SMPS to generate V_core logic supply
  • Ethernet compliant with IEEE-802.3-2002
  • USB OTG full speed or device only
  • Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45
  • Arm^® Mbed Enabled™ compliant

さらに表示

主な特徴

• Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
• Key features:
  • Low operating input voltage (from 1.4 V to 5.5 V)
  • Current capability from 200 mA to 300 mA
  • Low dropout (down to 160 mV typ.)
  • Ultra-low quiescent current (down to 500 nA typ.)
  • Low noise (down to 6.5 μVRMS typ.)
  • High PSSR (up to 80 dB)
  • Logic controlled electronic shutdown (enable)
  • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
• RoHS compliant

さらに表示

主な特徴

• Very compact module for motion, audio, environmental sensing and Bluetooth^® low energy connectivity with a complete set of firmware examples
• Mobile connectivity via the STBLESensor app, available for iOS™ and Android™
• Main components:
  • STM32L476JG – 32-bit ultra-low-power MCU with Cortex^® M4F
  • LSM6DSM – iNEMO inertial module: 3D accelerometer and 3D gyroscope
  • LSM303AGR – Ultra-compact high-performance eCompass module: ultra-low power 3D accelerometer and 3D magnetometer
  • LPS22HB – MEMS nano pressure sensor: 260-1260 hPa absolute digital output barometer
  • MP34DT05-A – 64 dB SNR digital MEMS microphone
  • BlueNRG-MS – Bluetooth low energy network processor
  • BALF-NRG-02D3 – 50 Ω balun with integrated harmonic filter
  • LD39115J18R – 150 mA low quiescent current low noise LDO 1.8 V
• 2 V - 5.5 V power supply range
• External interfaces: UART, SPI, SAI (Serial Audio Interface), I²C, DFSDM, USB OTG, ADC, GPIOs
• Solderable only interface (no connector on back side)
• SWD interface for debugging and programming capability
• CE certified
• RoHS and China RoHS compliant
• WEEE compliant
• FCC certified
• IC certified
• TYPE certified

さらに表示

主な特徴

• Contains FCC ID: S9NBCOIN01
• Contains module IC 8976C-BCOIN01 certified with PMN: STEVAL-BCNKT01V1; HVIN: STEVAL-BCNCS01V1; HMN: STEVAL-BCNCR01V1; FVIN: bluenrg_7_2_c_Mode_2-32MHz-XO32K_4M.img
• The development kit package includes:
  • BlueCoin module (STEVAL-BCNCS01V1) with STM32F446, LSM6DSM, LSM303AGR, LPS22HB, 4x MP34DT06J, BlueNRG-MS, BALF-NRG-01D3, STBC03JR
  • CoinStation (STEVAL-BCNST01V1) board
  • BlueCoin Cradle (STEVAL-BCNCR01V1)
  • 130 mAh Li-Po battery
  • Plastic box for housing the BlueCoin cradle and the battery
  • SWD programming cable
• Software libraries and tools:
  • STSW-BCNKT01 firmware package with raw sensor data streaming support via USB, data logging on SDCard, audio acquisition and audio streaming, time-of-flight example and BLE protocol to interface to a Smartphone App
  • FP-AUD-SMARTMIC1: smart audio IN-OUT software expansion for STM32Cube
  • FP-SNS-ALLMEMS1: STM32 ODE function pack for BLE and sensors
  • FP-AUD-BVLINK1: BLE and microphones software expansion for STM32Cube
  • STBLESensor: iOS™ and Android™ demo apps
  • BlueST-SDK: iOS and Android software development kit
  • Compatible with STM32 ecosystem through STM32Cube support

さらに表示

主な特徴

• STWLC33 evaluation board with Würth Elektronik dual mode coil (760308102207)
• Qi 1.2 compliant, supporting extended power profile: up to 15 W/10 V maximum output power
• Backward compatible with Qi baseline power profile: up to 5 W/5 V maximum output power
• PMA-SR1 (AirFuel inductive) compliant: 5 W/5.6 V maximum output power
• Transmitter function based on Qi protocol to charge wearable devices using the same Rx coil (up to 3 W power)
• Total system efficiency up to 80%
• Configurable GPIOs for status indication
• I²C interface for communication with the host system
• Foreign object detection (FOD)
• Complete kit (IC, firmware)
• RoHS compliant

さらに表示

主な特徴

• Bluetooth^® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
• Associated BlueNRG-2 development kit SW package including firmware and documentation
• Up to +8 dBm available output power (at antenna connector)
• Excellent receiver sensitivity (-88 dBm)
• Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
• Bluetooth^® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
• New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
• SMA connector for antenna or measuring equipment
• 3 user LEDs
• 2 user buttons
• 3D digital accelerometer and 3D digital gyroscope
• MEMS pressure sensor with embedded temperature sensor
• RoHS compliant

さらに表示

主な特徴

• 2 on-board MP34DT01-M digital MEMS microphones
• 6 slots to plug in digital microphone coupon boards such as STEVAL-MKI129Vx and STEVAL-MKI155Vx
• Synchronized acquisition and streaming of up to 4 microphones
• Free comprehensive development firmware library and audio capture plus USB streaming sample application which is compatible with STM32Cube firmware
• Compatible with STM32 Nucleo boards
• Equipped with ST morpho connector (upwards and downwards)
• Equipped with Arduino UNO R3 connector (upwards) to allow multiple boards
• RoHS compliant

さらに表示

主な特徴

• 1x VL6180X (proximity, gesture and ambient light sensing module) expansion board.
  • Slider switch controlling 2 functions:
  • 4-digit display, displaying either the distance of a target from the proximity sensor or the lux value from the ambient light sensing (ALS).
  • Excellent ranging accuracy, independent of the reflectance of the target.
• 1x NUCLEO-F401RE board
• Power management access point
• Equipped with Arduino UNO R3 connector.
• RoHS compliant.
• Full system SW supplied, download from www.st.com/vl6180x in the folder “Design resources”.
• 3x VL6180X satellite boards can be connected on the VL6180X expansion board, in order to integrate the VL6180X in customer’s application.
• Basic gesture recognition application can be developed using the VL6180X sensor on the expansion board and/or up to three sensors on the satellite boards.

さらに表示

主な特徴

• Ready-to-use printed circuit board (PCB) including:
  • M24SR64-Y Dynamic NFC/RFID tag
  • 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
  • STM32F103RGT6 64LQFP 32-bit microcontroller, with 1Mbytes of Flash memory
  • LCD Color Screen (320*200 pixels)
  • Different color LEDs
  • USB microB connector for board powering
  • JTAG connector for microcontroller firmware upgrade and debug
  • Joystick for menu selection
• M24SR-DISCO-PREM specific features:
  • Bluetooth module with audio outputs connected to Jack 3.5
  • Headset

さらに表示

主な特徴

• Complete HTS221 pinout (SPI & I²C interface) for a standard DIL 24 socket
• Fully compatible with STEVAL-MKI109V2 motherboard
• RoHS compliant

さらに表示

主な特徴

• M24SR64-Y Dynamic NFC/RFID tag IC
• NFC antenna: 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• Powered through the Arduino UNO R3 connectors
• 3 color LEDs for general purpose

さらに表示