製品概要
概要
The CR95HF is an integrated transceiver IC for contactless applications.
The CR95HF manages frame coding and decoding in Reader mode for standard applications such as near field communication (NFC), proximity and vicinity standards.
The CR95HF embeds an Analog Front End to provide the 13.56 MHz Air Interface.
The CR95HF supports ISO/IEC 14443 Type A and B, ISO/IEC 15693 (single or double subcarrier) and ISO/IEC 18092 communication protocols.
The CR95HF also supports the detection, reading and writing of NFC Forum Type 1, 2, 3 and 4 tags.
-
特徴
- CR95HF belongs to the ST25 family which includes all ST’s NFC/RFID tag and reader products
- Operating modes supported:
- Reader/Writer
- Hardware features
- Dedicated internal frame controller
- Highly integrated Analog Front End (AFE) for RF communications
- Transmission and reception modes
- Optimized power management
- Tag Detection mode
- RF communication @13.56 MHz
- ISO/IEC 14443 Type A and B
- ISO/IEC 15693
- ISO/IEC 18092
- MIFARE® Classic compatible 12
- Communication interfaces with a Host Controller
- Serial peripheral interface (SPI) Slave interface
- Universal asynchronous receiver/transmitter (UART)
- Up to 528-byte command/reception buffer (FIFO)
- 32-lead, 5x5 mm, very thin fine pitch quad flat (VFQFPN) ECOPACK®2 package
回路ダイアグラム
eDesignSuite
eDesignSuite is a comprehensive set of easy-to-use design-aid utilities ready to help you streamline the system development process with a wide range of ST products.
Power Management Design Center
Thermal-electrical Simulators for Components
Signal Conditioning Design Tool
NFC/RFID Calculators
Power Supply Design Tool
SMPS design, by topology, by type and by product PFC design with analog and digitial control Supports various PCB configurations 
LED Lighting Design Tool
Handles AC-DC and DC-DC design in common topologies Displays interactive and annotated schematic Provides current/voltage graphs, Bode plots, efficiency curves and power-loss data 
Digital Power Workbench
Provides a step-by-step optimized design of power section and control loop Generates the STM32Cube embedded software package for custom applications and allows firmware project generation, compatible with multiple STM32 IDEs 
Power Tree Designer
Specify input/output power for each node in the tree Check for consistency Design each individual node 
AC Switches Simulator
Select ratings and application waveforms Get junction temperature and blocking voltage graphs Search and sort suitable devices 
Rectifier Diodes Simulator
Select ratings and application waveforms Estimate power losses Search and sort suitable devices 
STPOWER Studio
Supports long mission profiles Provides power loss and temperature graphs Helps define heatsink thermal properties 
Twister Sim
Help select the right ViPOWER Automotive power device Supports load-compatibility, wiring harness optimization, fault condition impact and diagnostic analysis Supports various PCB configurations 
TVS Simulator
Specify system ratings and surge waveform Search and sort suitable devices 
Active Filters
Handles multi-stage-designs and common topologies Returns circuit component values Provides gain, phase and group delay graphs Low Pass, High Pass and Band Pass 
Comparators
Handles most common configurations Returns circuit components values Provides I/O signal waveforms Inverting, Non Inverting, Window 
Low side Current Sensing
Returns circuit component values Provides current error graphs 
High side Current Sensing
Provides current error graphs. Help to select the right High side current sensing and shunt devices. 
NFC Inductance
Input geometry and substrate properties Get antenna impedance 
UHF Link Budget
Enter forward and reverse link characteristics The tool returns link budget estimate 
NFC Tuning Circuit
Enter antenna parameter and matching target Select the topology of the matching network The tool returns component values for the desired design targets おすすめ製品
注目ビデオ
EDAシンボル / フットプリント / 3Dモデル
STMicroelectronics - CR95HF
Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.
Please select one model supplier :
EDAシンボル
フットプリント
3Dモデル
すべてのリソース
| タイトル | バージョン | 更新日 |
|---|
Schematic Pack (1)
| タイトル | バージョン | 更新日 | ||
|---|---|---|---|---|
| ZIP | 1.0 | 01 Aug 2015 | 01 Aug 2015 |
品質 & 信頼性
| 製品型番 | マーケティング･ステータス | パッケージ | グレード | RoHSコンプライアンスグレード | 材料宣誓書** |
|---|---|---|---|---|---|
| CR95HF-VMD5T | 量産中 | VFQFPN 32 5x5x1.0 mm | インダストリアル | Ecopack2 |
(**) st.comで提供している材料宣誓書は、パッケージ･ファミリ内で最も一般的に使用されているパッケージに基づく汎用ドキュメントの場合があります。そのため、特定の製品では100%正確ではない可能性があります。特定の製品情報については、セールスサポートまでお問い合わせください
サンプル & 購入
| 製品型番 | Order from distributors | STから購入 | 製品ステータス | ECCN (US) | ECCN (EU) | 梱包タイプ | パッケージ | 温度（℃） | Country of Origin | ESample Max Qty | Free Samples | Budgetary Price (US$)*/Qty | Country of Origin | ESample Max Qty | Free Samples | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 最小 | 最大 | ||||||||||||||||
| CR95HF-VMD5T | distributors 販売代理店に在庫がない場合は、STのセールス･オフィスまでお問い合わせください | 量産中 | EAR99 | NEC | Tape and Reel | VFQFPN 32 5x5x1.0 mm | -25 | 85 | PHILIPPINES | - | - | | PHILIPPINES | - | - | ||
販売代理店に在庫がない場合は、STのセールス･オフィスまでお問い合わせください
（*）概算用の参考価格（US$）です。現地通貨でのお見積りについては、STのセールス･オフィスまたは販売代理店までお問い合わせください。