ガイダンス & ポジショニング

Key Features

• STM32F407IGH6 microcontroller
• 16-Mbit SRAM
• microSD™ memory-card slot (card provided)
• Boot from user Flash memory, system memory or SRAM
• ISO/IEC 14443 smartcard Type-A and Type-B support
• I² C-bus interface for compatible 64-Kbit EEPROMs, ST MEMSs and I/O expanders
• IEEE 802.3-2002-compliant Ethernet connector
• Two CAN-2.0 A/B channels on the same D-subminiature connector
• RS-232 communications
• IrDA transceiver (up to board version MB786 C-07)
• USB-OTG (HS and FS) ports with Micro-AB connectors
• Induction-motor control connector
• I² S audio DAC, stereo audio jack for headset
• 3.2" 240x320 TFT color LCD with touch screen
• 4 colored LEDs
• Camera module and extension connector for ST-camera plug-in
• Joystick with 4-direction control and selector
• Reset, wakeup, tamper and user buttons
• RTC with backup battery
• Extension connector for daughterboard or wire-wrap board
• JTAG, SW and trace debug support
• Embedded ST-LINK/V2
• Five options for 5-V power supply: power jack, USB-FS connector, USB-HS connector, via ST-LINK/V2 or daughterboard

さらに表示

Key Features

• 4.5 V to 60 V input voltage
• Step-down (buck) conversion
• 3.3 V output voltage
• Up to 3 A DC output current
• 500 kHz switching frequency
• 3.5 ms programmed soft-start
• Compliant with ceramic output capacitors
• 180° out-of-phase synchronization available
• Auto recovery overcurrent and thermal protection
• RoHS and China RoHS compliant
• WEEE compliant (2012/19/UE RAEE II)

さらに表示

Key Features

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F103RET6 high-performance ARM Cortex^™ -M3 microcontroller
• Includes a DIL24 socket for easy MEMS adapter connection
• 3 V on-board linear voltage regulator
• DFU compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Debugging connector for SWD/JTAG
• RoHS compliant

さらに表示

Key Features

• Common features
  • STM32 microcontroller in LQFP64 package
  • 1 user LED shared with Arduino™
  • 1 user and 1 reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External SMPS to generate V_core logic supply
  • 24 MHz HSE
  • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI^® debug connector
  • Arm^® Mbed Enabled™ compliant

さらに表示

Key Features

• Complete LIS2DH12 pinout for a standard DIL 24 socket
• Fully compatible with STEVAL-MKI109V2 motherboard
• RoHS compliant

さらに表示

Key Features

• Common features
  • STM32 microcontroller in LQFP64 package
  • 1 user LED shared with Arduino™
  • 1 user and 1 reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External SMPS to generate V_core logic supply
  • 24 MHz HSE
  • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI^® debug connector
  • Arm^® Mbed Enabled™ compliant

さらに表示

Key Features

• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• 30 μA IQ at light load (LCM V_OUT = 3.3 V)
• 5 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_{DS(on) HS} = 180 mΩ, R_{DS(on) LS} = 110 mΩ
• Thermal shutdown

さらに表示

Key Features

• • 2 MHz or 3 MHz switching frequency
  • 1.2 A max. charging current
  • 20 V tolerant input with OVP
  • Programmable input current limitation and dynamic input current limit
  • Battery overvoltage protection
  • Auto-recharge
  • Integrated current sensing resistor
  • USB compatible
• Voltage mode fuel gauge
  • External sensing resistor not needed
  • Battery swap detection through ID resistor
  • Low battery voltage and low SOC programmable alarms
• 50 mA LDO for system boot in dead battery condition
• USB OTG VBUS generation (500 mA)
  • USB overvoltage protection
  • Programmable battery overcurrent protection
• Automatic 60 mA input pre-bias
• I²C compatible control interface
• Interrupt output pin
• RoHS compliant

さらに表示

Key Features

• Common features
  • STM32 microcontroller in LQFP64 package
  • 1 user LED shared with Arduino™
  • 1 user and 1 reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External SMPS to generate V_core logic supply
  • 24 MHz HSE
  • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI^® debug connector
  • Arm^® Mbed Enabled™ compliant

さらに表示

Key Features

• STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
• X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
• SPBTLE-RF:
  • Bluetooth Low Energy FCC and IC certified module based on Bluetooth^® SMART 4.1 network processor BlueNRG-MS
  • Integrated Balun (BALF-NRG-01D3)
  • Chip antenna
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• Scalable solution, capable of cascading multiple boards for larger systems
• Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
• RoHS compliant

さらに表示

Key Features

• AECQ100 qualification
• 1.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 45 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 5 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

さらに表示

Key Features

• AECQ100 qualification
• 0.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_{Q -SHTDWN}
• Adjustable f _SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 3.3 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 360 mΩ ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

さらに表示

Key Features

• AECQ100 qualification
• 0.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 45 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 5 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 360 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

さらに表示

Key Features

• AECQ100 qualification
• 0.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 μA I_Q at light load (LCM V_IN = 12 V and V_OUT =3.3 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 360 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

さらに表示

Key Features

• AECQ100 qualification
• 1.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 3.3 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

さらに表示

Key Features

• Common features
  • STM32 microcontroller in LQFP64 package
  • 1 user LED shared with Arduino™
  • 1 user and 1 reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External SMPS to generate V_core logic supply
  • 24 MHz HSE
  • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI^® debug connector
  • Arm^® Mbed Enabled™ compliant

さらに表示

Key Features

• Includes the EMIF02-01OABRY highly integrated solution designed to suppress EMI noise and protect against ESD
• Attenuation profile compliant with BroadR Reach™ requirements, from - 40 °C to 125 °C
• Compliant with ISO10605, ISO7637-3 standards
• RoHS compliant

さらに表示

Key Features

• AECQ100 qualification
• 1.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 µA I_Q at light load (LCM V_IN = 12 V and V_OUT = 3.3 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

さらに表示

Key Features

• Input voltage 5 V
• 12 V output, step-up converter for transceiver supply voltage
• LIN transceiver
• CAN transceiver
• Automotive-grade ESD protection
• IEC61000-4-2 compatibility

さらに表示

Key Features

• LSM6DSL MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±245/±500/±1000/±2000 dps)
• LSM303AGR MEMS 3D accelerometer (±2/±4/±8/±16 g) and MEMS3D magnetometer (±50 gauss)
• LPS22HB MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
• HTS221: capacitive digital relative humidity and temperature
• DIL24 socket for additional MEMS adapters and other sensors
• Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
• I²C sensor hub features on LSM6DSL available
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• RoHS compliant

さらに表示

Key Features

• Complete LSM6DSL pinout for a standard DIL24 socket
• Fully compatible with the STEVAL-MKI109V2 and STEVAL-MKI109V3 motherboards
• RoHS compliant

さらに表示

Key Features

• S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
• STM32 Nucleo-64 development board with STM32L152RE MCU
• Suitable for wireless M-Bus systems
• Suitable for SigFox applications
• Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
• Programmable RF output power up to +27 dBm
• Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
• Air data rate from 0.3 to 500 kbps
• Excellent performance of receiver sensitivity (up to -130 dBm)
• Low duty cycle RX/TX operation mode
• Automatic acknowledgement, retransmission and timeout protocol engine
• SPI interface for microcontroller
• USB interface
• RoHS compliant

さらに表示

Key Features

• Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
• Key features:
  • Low operating input voltage (from 1.4 V to 5.5 V)
  • Current capability from 200 mA to 300 mA
  • Low dropout (down to 160 mV typ.)
  • Ultra-low quiescent current (down to 500 nA typ.)
  • Low noise (down to 6.5 μVRMS typ.)
  • High PSSR (up to 80 dB)
  • Logic controlled electronic shutdown (enable)
  • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
• RoHS compliant

さらに表示

Key Features

• Bluetooth^® SMART board based on the BlueNRG-1 Bluetooth low energy system on chip
• Associated BlueNRG-1 development kit SW package including firmware and documentation
• Up to +8 dBm available output power (at antenna connector)
• Excellent receiver sensitivity (-88 dBm)
• Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
• Bluetooth^® low energy compliant, supports master, slave and simultaneous master-and-slave roles
• New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
• SMA connector for antenna or measuring equipment
• 3 user LEDs
• 2 user buttons
• 3D digital accelerometer and 3D digital gyroscope
• MEMS pressure sensor with embedded temperature sensor
• Battery holder
• JTAG debug connector
• USB to serial bridge for providing I/O channel with the BlueNRG-1 device
• Jumper for measuring current for BlueNRG-1 only
• RoHS compliant

さらに表示

Key Features

• Bluetooth^® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
• Associated BlueNRG-2 development kit SW package including firmware and documentation
• Up to +8 dBm available output power (at antenna connector)
• Excellent receiver sensitivity (-88 dBm)
• Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
• Bluetooth^® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
• New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
• SMA connector for antenna or measuring equipment
• 3 user LEDs
• 2 user buttons
• 3D digital accelerometer and 3D digital gyroscope
• MEMS pressure sensor with embedded temperature sensor
• RoHS compliant

さらに表示

Key Features

• S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
• STM32 Nucleo-64 development board with STM32L0 MCU
• Suitable for Wireless M-Bus systems
• Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
• Programmable RF output power up to +16 dBm
• Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
• Air data rate from 0.3 to 500 kbps
• Ultra-low power consumption:
  • 6.7 mA RX
  • 10 mA TX @ +10 dBm
• Excellent performance of receiver sensitivity (up to -130 dBm)
• Low duty cycle RX/TX operation mode
• Automatic acknowledgement, retransmission, and timeout protocol engine
• SPI interface for microcontroller
• USB interface
• RoHS compliant

さらに表示

Key Features

• S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF module tuned for 430-470 MHz frequency bands
• STM32 Nucleo-64 development board with STM32L0 MCU
• Suitable for wireless M-Bus systems
• Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
• Programmable RF output power up to +16 dBm
• Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
• Air data rate from 0.3 to 500 kbps
• Ultra-low power consumption:
  • 6.7 mA RX
  • 10 mA TX at +10 dBm
• Excellent performance of receiver sensitivity (up to -130 dBm)
• Low duty cycle RX/TX operation mode
• Automatic acknowledgement, retransmission and timeout protocol engine
• SPI interface for microcontroller
• USB interface
• RoHS compliant

さらに表示

Key Features

• STM32F417IGH6 microcontroller
• 16-Mbit SRAM
• microSD™ memory-card slot (card provided)
• Boot from user Flash, system memory or SRAM
• ISO/IEC 14443 smartcard Type-A and Type-B support
• I² C-bus interface for compatible 64-Kbit EEPROMs, ST MEMSs and I/O expanders
• IEEE 802.3-2002 compliant Ethernet connector
• Two CAN-2.0 A/B channels on the same D-subminiature connector
• RS-232 communications
• IrDA transceiver (up to board version MB786 C-07)
• USB-OTG (HS and FS) ports with Micro-AB connectors
• Induction-motor control connector
• I² S Audio DAC, stereo audio jack for headset
• 3.2" 240x320 TFT color LCD with touch screen
• 4 colored LEDs
• Camera module and extension connector for ST-camera plug-in
• Joystick with 4-direction control and selector
• Reset, wakeup, tamper and user button
• RTC with backup battery
• Extension connector for daughterboard or wire-wrap board
• JTAG, SW and trace debug support
• Embedded ST-LINK/V2
• Five options for 5-V power supply: power jack, USB-FS connector, USB-HS connector, via ST-LINK/V2 or daughterboard

さらに表示