概要
ソリューション
HW評価ツール
リソース
Tools and Software
主要製品
Get Started

USB(Universal Serial Bus)は、最も広く使用されている有線接続テクノロジーの1つであり、コンピュータとその周辺機器、家電製品、自動車および工業用まであらゆるアプリケーションで使用されています。USBは、普及が進むにつれて、On-The-Go(OTG)機能を含み、より高いデータレートをサポートするように進化しました。今日、USBは、Type-CコネクタとPower Deliveryの登場で、より高い汎用性と大きな電力供給能力を実現しています。

STのポートフォリオには、OTGおよびUTMI+ ULPI(Ultra low pin interface)のサポートを含むUSBトランシーバがあります。さらに、STM32マイクロコントローラ向けファームウェアおよびアプリケーション・ソフトウェア・パッケージに加えて、専用保護ICもポートフォリオに含まれています。

推奨製品

製品型番
概要
STEVAL-USBPD45C 45 W USB Type-C™ Power Delivery adapter reference design based on STCH03, STM32F051 and STUSB1602A Quick view

主な特徴

  • USB PD 3.0 compliant
  • Universal input mains voltage range: from 90 VAC to 264 VAC (frequency from 45 Hz to 65 Hz)
  • Three fixed PDOs available: 5 V, 9 V, 15 V – 3 A continuous operation
  • Load power limited to 45 W
  • Minimum four-point average efficiency in active mode compliant with CoC ver. 5 – Tier 2 and DOE requirement
  • Efficiency > 50% with Pout = 250 mW
  • < 35 mW no-load standby power
  • Adaptive synchronous rectification with digital driver and controller
  • Load feedforward
  • OVP, UVP, OC, short-circuit protections
  • ESD protection: > 30 kV contact on VBUS and 20 kV contact on CC lines and according to IEC61000-4-2
  • Immunity against surge current on VBUS pin up to 35 A in a 8/20 µs waveform, according to IEC61000-4-5
  • Compact design: 73x51x25 mm
  • RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STM32G081B-EVAL Evaluation board with STM32G081RB MCU Quick view

主な特徴

  • Mother board
    • STM32G081RBT6 microcontroller with 128 Kbytes of Flash memory and 32 Kbytes of RAM in LQFP64 package
    • MCU voltage choice fixed 3.3 V or adjustable from 1.65 V to 3.6 V
    • I2 C compatible serial interface
    • RTC with backup battery
    • 8-Gbyte or more SPI interface microSD card
    • Potentiometer
    • 4 color user LEDs and one LED as MCU low-power alarm
    • Reset, Tamper and User buttons
    • 4-direction control and selection joystick
    • Board connectors:
      • 5 V power jack
      • RS-232 and RS485 communications
      • Stereo audio jack including analog microphone input
      • microSD card
      • Extension I2C connector
      • Motor-control connector
    • Board extension connectors:
      • Daughterboard connectors for legacy peripheral daughter board or USB-C daughterboard
      • Extension connectors for daughterboard or wire-wrap board
    • Flexible power-supply options:
      • 5 V power jack
      • ST-LINK/V2-1 USB connector
      • Daughterboard
    • On-board ST-LINK/V2-1 debugger/programmer with USB re- enumeration capability: mass storage, virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs
  • Legacy peripheral daughterboard
    • IrDA transceiver
    • IR LED and IR receiver
    • Light dependent resistor (LDR)
    • Temperature Sensor
    • Board connectors:
      • Two HDMI connectors with DDC and CEC
      • Smart card slot
  • USB-C and Power Delivery daughterboard
    • Mux for USB3.1 Gen1 / DisplayPort input and Type-C port1 output
    • Mux for Type-C port2 input and DisplayPort output / USB2.0
    • VCONN on Type-C port1
    • USB PD on Type-C port1
    • Board connectors:
      • Type-C port1 DRP (dual-role port)
      • Type-C port2 Sink
      • DisplayPort input
      • DisplayPort output
      • USB 3.1 Gen1 Type-B receptacle
      • USB2.0 Type-A receptacle
      • 19 V power jack for USB PD

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STM32G071B-DISCO USB Type-C and Power Delivery Discovery kit with STM32G071RB MCU Quick view

主な特徴

  • STM32G071RBT6 microcontroller featuring 128 Kbytes of Flash memory and 32 Kbytes of RAM in LQFP64 package
  • Plastic case
  • 1” 128 x 64 pixels OLED LCD module with SPI interface
  • USB Type-C™ interface plug cable and receptacle connector accessible by door with reed sensor detection
  • 3 bidirectional current and power monitors with I2 C interface to measure VBUS , CC1 and CC2 protected and isolated lines
  • On-board DC/DC converter to sustain power supply with VBUS varying from 3 V to 20 V (+/- 5 %)
  • 4 user status LEDs about USB Type-C™ configuration
  • 3 LEDs for power and ST-LINK communication
  • 4-way joystick with selection button
  • 1 reset push-button
  • Board external connectors:
    • USB Type-C™ plug cable
    • USB Type-C™ receptacle connector
    • 8-pin user extension connector including ADC, SPI, USART and I2 C communication signals
    • USB with Micro-AB (ST-LINK)
  • Board internal connectors:
    • 2 x 8-pin GPIOs free pins from microcontroller (accessible internally when case is removed)
    • USB Type-C™ test points for main signals
  • Flexible power-supply options: ST-LINK USB VBUS or USB Type-C™ VBUS
  • On-board ST-LINK/V2-1 debugger/programmer with USB enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube™ MCU Package
  • Support of a wide choice of integrated development environments (IDEs), including IAR™, Keil® and GCC-based IDEs

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-ISB047V1 Qi certified 3-coil 15 W wireless charger TX evaluation kit based on STWBC-MC Quick view

主な特徴

  • STWBC-MC digital controller
  • MP-A15 3-coil array
  • 15 W potential power
  • Flexible input voltage: 5 to 20 V from USB-C or DC jack
  • 5 W mode when connected to 5 V USB input or DC jack
  • Fixed frequency operation
  • WPC Qi1.2.4 standard certified
  • Robust demodulation algorithm, with triple path (V, I, f)
  • Foreign object detection (FOD)
  • Active presence detection
  • UART protocol to control and monitor the system
  • Complete reference design (evaluation board, schematics, PCB layout, firmware and tools)
  • 2-layer PCB
  • Low standby power consumption
  • Flash memory based
  • CE certified
  • RoHS compliant
  • WEEE compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STM32G474E-EVAL Evaluation board with STM32G474QE MCU Quick view

主な特徴

  • Common features
    • 240x320 TFT color LCD display module with SPI interface
    • 16-Gbyte microSD™ card bundled
    • On-board current measurement
    • SAI audio codec
    • Temperature sensor
    • 8-Mbit (512 K x 16-bit) SRAM
    • Two 512-Mbit Quad-SPI NOR Flash memories
    • Four color user LEDs
    • One high brightness LED
    • Reset and wake-up / tamper buttons
    • 4-direction joystick with selection button
    • Light-dependent resistor (LDR)
    • Potentiometer
    • Access to comparator and operational amplifier
    • Board connectors:Analog line input jackStereo headset jackTwo connectors for external speakersmicroSD™ cardEXT_I2C connector supporting I²C busRS-232 port configurable for communication or MCU flashingRS-485 portUSB Type-C™ port supporting USB FS DeviceTwo CAN 2.0A/B-compliant portsConnector for DAC outputJTAG/SWD connectorETM trace debug connectorUser interface through USB virtual COM portEmbedded STLINK-V3E debug and flashing facilityTAG connector 10-pin footprintArm® Cortex® 10-pin 1.27 mm-pitch debug connector over STDC14 footprintCoin cell battery holder
    • Board expansion connectors:Two sets of motor control expansion connectorsBoard expansion extension connectors
    • Flexible power-supply options:ST-LINK USB VBUS , external sources, USB Type-C™ connector, or daughterboard
    • On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
    • Microcontroller supply voltage: fixed 3.3 V or adjustable range from 1.62 V to 3.6 V
    • Comprehensive free software libraries and examples available with the STM32CubeG4 MCU Package
    • Support of a wide choice of integrated development environments (IDEs) including IAR™, Keil® , GCC-based IDEs
  • Board-specific features
    • STM32G474QET6U microcontroller with 512 Kbytes of Flash memory and 96 Kbytes of RAM in LQFP128 package (STM32G474E-EVAL and STM32G474E-EVAL1)
    • STM32G474E-EVAL1 is the board to use for motor control application with solder bridge and resistor configuration
    • STM32G484QET6U with cryptography (STM32G484E-EVAL)
  • Fully compatible with all microcontrollers of the STM32G4x1 and STM32G4x3 lines with "QET6" part number suffix

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STM32G484E-EVAL Evaluation board with STM32G484QE MCU Quick view

主な特徴

  • Common features
    • 240x320 TFT color LCD display module with SPI interface
    • 16-Gbyte microSD™ card bundled
    • On-board current measurement
    • SAI audio codec
    • Temperature sensor
    • 8-Mbit (512 K x 16-bit) SRAM
    • Two 512-Mbit Quad-SPI NOR Flash memories
    • Four color user LEDs
    • One high brightness LED
    • Reset and wake-up / tamper buttons
    • 4-direction joystick with selection button
    • Light-dependent resistor (LDR)
    • Potentiometer
    • Access to comparator and operational amplifier
    • Board connectors:Analog line input jackStereo headset jackTwo connectors for external speakersmicroSD™ cardEXT_I2C connector supporting I²C busRS-232 port configurable for communication or MCU flashingRS-485 portUSB Type-C™ port supporting USB FS DeviceTwo CAN 2.0A/B-compliant portsConnector for DAC outputJTAG/SWD connectorETM trace debug connectorUser interface through USB virtual COM portEmbedded STLINK-V3E debug and flashing facilityTAG connector 10-pin footprintArm® Cortex® 10-pin 1.27 mm-pitch debug connector over STDC14 footprintCoin cell battery holder
    • Board expansion connectors:Two sets of motor control expansion connectorsBoard expansion extension connectors
    • Flexible power-supply options:ST-LINK USB VBUS , external sources, USB Type-C™ connector, or daughterboard
    • On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
    • Microcontroller supply voltage: fixed 3.3 V or adjustable range from 1.62 V to 3.6 V
    • Comprehensive free software libraries and examples available with the STM32CubeG4 MCU Package
    • Support of a wide choice of integrated development environments (IDEs) including IAR™, Keil® , GCC-based IDEs
  • Board-specific features
    • STM32G474QET6U microcontroller with 512 Kbytes of Flash memory and 96 Kbytes of RAM in LQFP128 package (STM32G474E-EVAL and STM32G474E-EVAL1)
    • STM32G474E-EVAL1 is the board to use for motor control application with solder bridge and resistor configuration
    • STM32G484QET6U with cryptography (STM32G484E-EVAL)
  • Fully compatible with all microcontrollers of the STM32G4x1 and STM32G4x3 lines with "QET6" part number suffix

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-ISC005V1 Evaluation board for the STUSB4500 USB Power Delivery controller Quick view

主な特徴

  • USB PD port (sink)
  • STUSB4500 USB Power Delivery controller, certified for:
    • USB type-C™ (rev1.2)
    • USB PD (rev2.0)
    • TID: 1000133
  • Compliant with USB PD (rev3.0)
  • 5 V on-board DC-DC
  • VBUS power switches and discharge path
  • Support to up to 3 power data objects (PDO)
  • Short-to-VBUS protections on CC pins (22 V) and VBUS pins (28 V)
  • Customizable start-up profiles
  • Multiple output paths
  • Compatible with NUCLEO-F072RB development board for configuration and debug interface
  • CE certified
  • RoHS and China RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-ISC004V1 STUSB4710A evaluation board (with on-board DC-DC) Quick view

主な特徴

  • 1 x USB PD port (source)
  • STUSB4710A USB power delivery controller
  • Compliant with:
    • USB Type-C r1.2
    • USB PD r2.0
  • On-board DC-DC
  • VBUS power switches and discharge path
  • Support for up to 5 power data objects (PDO)
  • Short-to-VBUS protections on CC pins (22 V) and VBUS pins (28 V)
  • Customizable start-up profiles
  • Compatible with NUCLEO-F072RB board for configuration and debug interface
  • RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-CCC002V1 STUSB1600A Type-C™ controller evaluation board Quick view

主な特徴

  • 1 full-featured USB Type-C port (Source/Sink/Dual-role)
  • STUSB1600A Type-C controller compliant with USB Type-C standard rel. 1.2 + ECR
  • VBUS power switches and discharge path
  • VCONN support (programmable current limit up to 600 mA)
  • Dead Battery mode support
  • Compatible with NUCLEO-F072RB board for configuration and debug interface

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-USBPD45H USB Power Delivery (Type-C PD) 45 W USB wall power adapter solution based on STCH02 and STUSB4700 Quick view

主な特徴

  • USB wall power adapter input: 85 VAC to 264 VAC
  • USB voltage output: 5 V, 9 V and 15 V
  • Current limit: 3 A for all voltage level profiles
  • Load power limited to 45 W
  • Cable compensation
  • Isolated quasi-resonant flyback
  • Efficiency 90% (approx.)
  • USB Type-C Power Delivery compatible
  • USB-IF certified

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
P-NUCLEO-USB002 STUSB1602 USB Type-C and Power Delivery Nucleo Pack with NUCLEO-F072RB Quick view

主な特徴

  • 32-bit ARM® Cortex® -M0-based microcontroller STM32F072RB with 128 kB Flash and 16 kB SRAM
  • Dual port solution based on certified USB Type-C™ port controller STUSB1602, featuring:
    • Type-C FSM with attach/detach and cable orientation detection
    • USB PD PHY and BMC transceiver
    • High voltage (20 V) technology
    • VBUS voltage monitoring
    • 600 mA VCONN power switch
    • VBUS and VCONN discharge paths
    • Dead-battery support
    • 22 V CC line protection
    • VBUS switch gate drivers
  • Power connector to interface with external power supply (not included)
  • USB 2.0 full speed data communication interface
  • RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-OET004V1 USB Type-C protection and filtering demo PCB Quick view

主な特徴

  • Protection of all lines (data, control and power)
  • Common mode filters for USB 2.0 and USB 3.1 lines on STEVAL-OET004V1D
  • Plug and receptacle enabling insertion of the PCB between host and cable or device and cable

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-USBC2DP USB Type-C™ to DisplayPort™ adapter Quick view

主な特徴

  • Full reference design for USB Type-C to DisplayPort adapter with USB Type-C connector and DisplayPort connector.
  • Single chip solution based on the STM32F072 series 32-bit microcontrollers with integrated USB 2.0 peripheral.
  • Based on certified X-CUBE-USB-PD middleware stack, compliant with the following standards and specifications:
    • USB Type-C Cable and Connector 1.3
    • USB Power Delivery 2.0 and 3.0
    • VESA DisplayPort Alternate Mode on USB Type-C Standard 1.0a
    • USB Device Class Definition for Billboard Devices 1.21
  • EMI filtering and ESD protection circuits.
  • Compact PCB design: 5.5 x 2.3 cm
  • RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-STRKT01 LoRa® IoT tracker Quick view

主な特徴

  • Optimized IoT tracker solution over LoRaWAN™ network with simultaneous multi-constellation GNSS positioning and geofencing support
  • Battery operated solution with smart power management architecture
  • First IoT ST reference embedding a USB Type-C connector and a port controller
  • Environmental and motion sensors
  • Data logging
  • STM32Cube function pack (FP-ATR-LORA1)
  • High flexibility to cover different application profiles:
    • asset tracker
    • people and animal tracker
    • fleet management
  • WEEE and RoHS compliant
  • 2006/66/EC Directive compliant
  • Contains trasmitter module FCC ID: VPYCMABZ and IC ID: 772C-CMABZ
  • CE certified

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
NUCLEO-L552ZE-Q STM32 Nucleo-144 development board with STM32L552ZE MCU, SMPS, supports Arduino, ST Zio and morpho connectivity Quick view

主な特徴

  • Common features
    • STM32 microcontroller in LQFP144 package
    • 3 user LEDs
    • 2 user and reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:SWDST Zio expansion connector including ARDUINO® Uno V3ST morpho expansion connector
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External or internal SMPS to generate Vcore logic supply
    • Ethernet compliant with IEEE-802.3-2002
    • USB OTG full speed or device only
    • Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45
    • Arm® Mbed Enabled™ compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
EVAL-SCS001V1 Fast and easy migration from DC barrel to Type-C Quick view

主な特徴

  • USB Power Delivery SINK port
  • Short-to VBUS protection up to 28 V
  • Low BOM cost, small footprint
  • Status LED

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-STWINWFV1 Wi-Fi expansion for the SensorTile Wireless Industrial Node (STWIN) kit Quick view

主な特徴

  • Wi-Fi adapter for STWIN (STEVAL-STWINKT1)
  • Plugs into STWIN core system board through dedicated 12-pin connector
  • Single 3.3 V power supply input
  • ISM43362-M3G-L44-E Wi-Fi module:
    • 802.11 b/g/n Compatible based on Broadcom MAC/Baseband/Radio device
    • Fully contained TCP/IP stack
    • Host interface: SPI up to 25 MHz
    • Network features ICMP ( Ping), ARP, DHCP,TCP, UDP
    • Low power operation (3.3 V supply) with built-in low power modes
    • Secure Wi-Fi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK
    • CE certified
    • FCC certified
    • IC certified
  • RoHS and China RoHS compliant
  • WEEE compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
製品型番
STEVAL-USBPD45C

45 W USB Type-C™ Power Delivery adapter reference design based on STCH03, STM32F051 and STUSB1602A

主な特徴

  • USB PD 3.0 compliant
  • Universal input mains voltage range: from 90 VAC to 264 VAC (frequency from 45 Hz to 65 Hz)
  • Three fixed PDOs available: 5 V, 9 V, 15 V – 3 A continuous operation
  • Load power limited to 45 W
  • Minimum four-point average efficiency in active mode compliant with CoC ver. 5 – Tier 2 and DOE requirement
  • Efficiency > 50% with Pout = 250 mW
  • < 35 mW no-load standby power
  • Adaptive synchronous rectification with digital driver and controller
  • Load feedforward
  • OVP, UVP, OC, short-circuit protections
  • ESD protection: > 30 kV contact on VBUS and 20 kV contact on CC lines and according to IEC61000-4-2
  • Immunity against surge current on VBUS pin up to 35 A in a 8/20 µs waveform, according to IEC61000-4-5
  • Compact design: 73x51x25 mm
  • RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STM32G081B-EVAL

Evaluation board with STM32G081RB MCU

主な特徴

  • Mother board
    • STM32G081RBT6 microcontroller with 128 Kbytes of Flash memory and 32 Kbytes of RAM in LQFP64 package
    • MCU voltage choice fixed 3.3 V or adjustable from 1.65 V to 3.6 V
    • I2 C compatible serial interface
    • RTC with backup battery
    • 8-Gbyte or more SPI interface microSD card
    • Potentiometer
    • 4 color user LEDs and one LED as MCU low-power alarm
    • Reset, Tamper and User buttons
    • 4-direction control and selection joystick
    • Board connectors:
      • 5 V power jack
      • RS-232 and RS485 communications
      • Stereo audio jack including analog microphone input
      • microSD card
      • Extension I2C connector
      • Motor-control connector
    • Board extension connectors:
      • Daughterboard connectors for legacy peripheral daughter board or USB-C daughterboard
      • Extension connectors for daughterboard or wire-wrap board
    • Flexible power-supply options:
      • 5 V power jack
      • ST-LINK/V2-1 USB connector
      • Daughterboard
    • On-board ST-LINK/V2-1 debugger/programmer with USB re- enumeration capability: mass storage, virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs
  • Legacy peripheral daughterboard
    • IrDA transceiver
    • IR LED and IR receiver
    • Light dependent resistor (LDR)
    • Temperature Sensor
    • Board connectors:
      • Two HDMI connectors with DDC and CEC
      • Smart card slot
  • USB-C and Power Delivery daughterboard
    • Mux for USB3.1 Gen1 / DisplayPort input and Type-C port1 output
    • Mux for Type-C port2 input and DisplayPort output / USB2.0
    • VCONN on Type-C port1
    • USB PD on Type-C port1
    • Board connectors:
      • Type-C port1 DRP (dual-role port)
      • Type-C port2 Sink
      • DisplayPort input
      • DisplayPort output
      • USB 3.1 Gen1 Type-B receptacle
      • USB2.0 Type-A receptacle
      • 19 V power jack for USB PD

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STM32G071B-DISCO

USB Type-C and Power Delivery Discovery kit with STM32G071RB MCU

主な特徴

  • STM32G071RBT6 microcontroller featuring 128 Kbytes of Flash memory and 32 Kbytes of RAM in LQFP64 package
  • Plastic case
  • 1” 128 x 64 pixels OLED LCD module with SPI interface
  • USB Type-C™ interface plug cable and receptacle connector accessible by door with reed sensor detection
  • 3 bidirectional current and power monitors with I2 C interface to measure VBUS , CC1 and CC2 protected and isolated lines
  • On-board DC/DC converter to sustain power supply with VBUS varying from 3 V to 20 V (+/- 5 %)
  • 4 user status LEDs about USB Type-C™ configuration
  • 3 LEDs for power and ST-LINK communication
  • 4-way joystick with selection button
  • 1 reset push-button
  • Board external connectors:
    • USB Type-C™ plug cable
    • USB Type-C™ receptacle connector
    • 8-pin user extension connector including ADC, SPI, USART and I2 C communication signals
    • USB with Micro-AB (ST-LINK)
  • Board internal connectors:
    • 2 x 8-pin GPIOs free pins from microcontroller (accessible internally when case is removed)
    • USB Type-C™ test points for main signals
  • Flexible power-supply options: ST-LINK USB VBUS or USB Type-C™ VBUS
  • On-board ST-LINK/V2-1 debugger/programmer with USB enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube™ MCU Package
  • Support of a wide choice of integrated development environments (IDEs), including IAR™, Keil® and GCC-based IDEs

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-ISB047V1

Qi certified 3-coil 15 W wireless charger TX evaluation kit based on STWBC-MC

主な特徴

  • STWBC-MC digital controller
  • MP-A15 3-coil array
  • 15 W potential power
  • Flexible input voltage: 5 to 20 V from USB-C or DC jack
  • 5 W mode when connected to 5 V USB input or DC jack
  • Fixed frequency operation
  • WPC Qi1.2.4 standard certified
  • Robust demodulation algorithm, with triple path (V, I, f)
  • Foreign object detection (FOD)
  • Active presence detection
  • UART protocol to control and monitor the system
  • Complete reference design (evaluation board, schematics, PCB layout, firmware and tools)
  • 2-layer PCB
  • Low standby power consumption
  • Flash memory based
  • CE certified
  • RoHS compliant
  • WEEE compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STM32G474E-EVAL

Evaluation board with STM32G474QE MCU

主な特徴

  • Common features
    • 240x320 TFT color LCD display module with SPI interface
    • 16-Gbyte microSD™ card bundled
    • On-board current measurement
    • SAI audio codec
    • Temperature sensor
    • 8-Mbit (512 K x 16-bit) SRAM
    • Two 512-Mbit Quad-SPI NOR Flash memories
    • Four color user LEDs
    • One high brightness LED
    • Reset and wake-up / tamper buttons
    • 4-direction joystick with selection button
    • Light-dependent resistor (LDR)
    • Potentiometer
    • Access to comparator and operational amplifier
    • Board connectors:Analog line input jackStereo headset jackTwo connectors for external speakersmicroSD™ cardEXT_I2C connector supporting I²C busRS-232 port configurable for communication or MCU flashingRS-485 portUSB Type-C™ port supporting USB FS DeviceTwo CAN 2.0A/B-compliant portsConnector for DAC outputJTAG/SWD connectorETM trace debug connectorUser interface through USB virtual COM portEmbedded STLINK-V3E debug and flashing facilityTAG connector 10-pin footprintArm® Cortex® 10-pin 1.27 mm-pitch debug connector over STDC14 footprintCoin cell battery holder
    • Board expansion connectors:Two sets of motor control expansion connectorsBoard expansion extension connectors
    • Flexible power-supply options:ST-LINK USB VBUS , external sources, USB Type-C™ connector, or daughterboard
    • On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
    • Microcontroller supply voltage: fixed 3.3 V or adjustable range from 1.62 V to 3.6 V
    • Comprehensive free software libraries and examples available with the STM32CubeG4 MCU Package
    • Support of a wide choice of integrated development environments (IDEs) including IAR™, Keil® , GCC-based IDEs
  • Board-specific features
    • STM32G474QET6U microcontroller with 512 Kbytes of Flash memory and 96 Kbytes of RAM in LQFP128 package (STM32G474E-EVAL and STM32G474E-EVAL1)
    • STM32G474E-EVAL1 is the board to use for motor control application with solder bridge and resistor configuration
    • STM32G484QET6U with cryptography (STM32G484E-EVAL)
  • Fully compatible with all microcontrollers of the STM32G4x1 and STM32G4x3 lines with "QET6" part number suffix

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STM32G484E-EVAL

Evaluation board with STM32G484QE MCU

主な特徴

  • Common features
    • 240x320 TFT color LCD display module with SPI interface
    • 16-Gbyte microSD™ card bundled
    • On-board current measurement
    • SAI audio codec
    • Temperature sensor
    • 8-Mbit (512 K x 16-bit) SRAM
    • Two 512-Mbit Quad-SPI NOR Flash memories
    • Four color user LEDs
    • One high brightness LED
    • Reset and wake-up / tamper buttons
    • 4-direction joystick with selection button
    • Light-dependent resistor (LDR)
    • Potentiometer
    • Access to comparator and operational amplifier
    • Board connectors:Analog line input jackStereo headset jackTwo connectors for external speakersmicroSD™ cardEXT_I2C connector supporting I²C busRS-232 port configurable for communication or MCU flashingRS-485 portUSB Type-C™ port supporting USB FS DeviceTwo CAN 2.0A/B-compliant portsConnector for DAC outputJTAG/SWD connectorETM trace debug connectorUser interface through USB virtual COM portEmbedded STLINK-V3E debug and flashing facilityTAG connector 10-pin footprintArm® Cortex® 10-pin 1.27 mm-pitch debug connector over STDC14 footprintCoin cell battery holder
    • Board expansion connectors:Two sets of motor control expansion connectorsBoard expansion extension connectors
    • Flexible power-supply options:ST-LINK USB VBUS , external sources, USB Type-C™ connector, or daughterboard
    • On-board STLINK-V3E debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port
    • Microcontroller supply voltage: fixed 3.3 V or adjustable range from 1.62 V to 3.6 V
    • Comprehensive free software libraries and examples available with the STM32CubeG4 MCU Package
    • Support of a wide choice of integrated development environments (IDEs) including IAR™, Keil® , GCC-based IDEs
  • Board-specific features
    • STM32G474QET6U microcontroller with 512 Kbytes of Flash memory and 96 Kbytes of RAM in LQFP128 package (STM32G474E-EVAL and STM32G474E-EVAL1)
    • STM32G474E-EVAL1 is the board to use for motor control application with solder bridge and resistor configuration
    • STM32G484QET6U with cryptography (STM32G484E-EVAL)
  • Fully compatible with all microcontrollers of the STM32G4x1 and STM32G4x3 lines with "QET6" part number suffix

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-ISC005V1

Evaluation board for the STUSB4500 USB Power Delivery controller

主な特徴

  • USB PD port (sink)
  • STUSB4500 USB Power Delivery controller, certified for:
    • USB type-C™ (rev1.2)
    • USB PD (rev2.0)
    • TID: 1000133
  • Compliant with USB PD (rev3.0)
  • 5 V on-board DC-DC
  • VBUS power switches and discharge path
  • Support to up to 3 power data objects (PDO)
  • Short-to-VBUS protections on CC pins (22 V) and VBUS pins (28 V)
  • Customizable start-up profiles
  • Multiple output paths
  • Compatible with NUCLEO-F072RB development board for configuration and debug interface
  • CE certified
  • RoHS and China RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-ISC004V1

STUSB4710A evaluation board (with on-board DC-DC)

主な特徴

  • 1 x USB PD port (source)
  • STUSB4710A USB power delivery controller
  • Compliant with:
    • USB Type-C r1.2
    • USB PD r2.0
  • On-board DC-DC
  • VBUS power switches and discharge path
  • Support for up to 5 power data objects (PDO)
  • Short-to-VBUS protections on CC pins (22 V) and VBUS pins (28 V)
  • Customizable start-up profiles
  • Compatible with NUCLEO-F072RB board for configuration and debug interface
  • RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-CCC002V1

STUSB1600A Type-C™ controller evaluation board

主な特徴

  • 1 full-featured USB Type-C port (Source/Sink/Dual-role)
  • STUSB1600A Type-C controller compliant with USB Type-C standard rel. 1.2 + ECR
  • VBUS power switches and discharge path
  • VCONN support (programmable current limit up to 600 mA)
  • Dead Battery mode support
  • Compatible with NUCLEO-F072RB board for configuration and debug interface

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-USBPD45H

USB Power Delivery (Type-C PD) 45 W USB wall power adapter solution based on STCH02 and STUSB4700

主な特徴

  • USB wall power adapter input: 85 VAC to 264 VAC
  • USB voltage output: 5 V, 9 V and 15 V
  • Current limit: 3 A for all voltage level profiles
  • Load power limited to 45 W
  • Cable compensation
  • Isolated quasi-resonant flyback
  • Efficiency 90% (approx.)
  • USB Type-C Power Delivery compatible
  • USB-IF certified

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
P-NUCLEO-USB002

STUSB1602 USB Type-C and Power Delivery Nucleo Pack with NUCLEO-F072RB

主な特徴

  • 32-bit ARM® Cortex® -M0-based microcontroller STM32F072RB with 128 kB Flash and 16 kB SRAM
  • Dual port solution based on certified USB Type-C™ port controller STUSB1602, featuring:
    • Type-C FSM with attach/detach and cable orientation detection
    • USB PD PHY and BMC transceiver
    • High voltage (20 V) technology
    • VBUS voltage monitoring
    • 600 mA VCONN power switch
    • VBUS and VCONN discharge paths
    • Dead-battery support
    • 22 V CC line protection
    • VBUS switch gate drivers
  • Power connector to interface with external power supply (not included)
  • USB 2.0 full speed data communication interface
  • RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-OET004V1

USB Type-C protection and filtering demo PCB

主な特徴

  • Protection of all lines (data, control and power)
  • Common mode filters for USB 2.0 and USB 3.1 lines on STEVAL-OET004V1D
  • Plug and receptacle enabling insertion of the PCB between host and cable or device and cable

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-USBC2DP

USB Type-C™ to DisplayPort™ adapter

主な特徴

  • Full reference design for USB Type-C to DisplayPort adapter with USB Type-C connector and DisplayPort connector.
  • Single chip solution based on the STM32F072 series 32-bit microcontrollers with integrated USB 2.0 peripheral.
  • Based on certified X-CUBE-USB-PD middleware stack, compliant with the following standards and specifications:
    • USB Type-C Cable and Connector 1.3
    • USB Power Delivery 2.0 and 3.0
    • VESA DisplayPort Alternate Mode on USB Type-C Standard 1.0a
    • USB Device Class Definition for Billboard Devices 1.21
  • EMI filtering and ESD protection circuits.
  • Compact PCB design: 5.5 x 2.3 cm
  • RoHS compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber

主な特徴

  • Optimized IoT tracker solution over LoRaWAN™ network with simultaneous multi-constellation GNSS positioning and geofencing support
  • Battery operated solution with smart power management architecture
  • First IoT ST reference embedding a USB Type-C connector and a port controller
  • Environmental and motion sensors
  • Data logging
  • STM32Cube function pack (FP-ATR-LORA1)
  • High flexibility to cover different application profiles:
    • asset tracker
    • people and animal tracker
    • fleet management
  • WEEE and RoHS compliant
  • 2006/66/EC Directive compliant
  • Contains trasmitter module FCC ID: VPYCMABZ and IC ID: 772C-CMABZ
  • CE certified

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
NUCLEO-L552ZE-Q

STM32 Nucleo-144 development board with STM32L552ZE MCU, SMPS, supports Arduino, ST Zio and morpho connectivity

主な特徴

  • Common features
    • STM32 microcontroller in LQFP144 package
    • 3 user LEDs
    • 2 user and reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:SWDST Zio expansion connector including ARDUINO® Uno V3ST morpho expansion connector
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External or internal SMPS to generate Vcore logic supply
    • Ethernet compliant with IEEE-802.3-2002
    • USB OTG full speed or device only
    • Board connectors:USB with Micro-AB or USB Type-C™Ethernet RJ45
    • Arm® Mbed Enabled™ compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
EVAL-SCS001V1

Fast and easy migration from DC barrel to Type-C

主な特徴

  • USB Power Delivery SINK port
  • Short-to VBUS protection up to 28 V
  • Low BOM cost, small footprint
  • Status LED

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
STEVAL-STWINWFV1

Wi-Fi expansion for the SensorTile Wireless Industrial Node (STWIN) kit

主な特徴

  • Wi-Fi adapter for STWIN (STEVAL-STWINKT1)
  • Plugs into STWIN core system board through dedicated 12-pin connector
  • Single 3.3 V power supply input
  • ISM43362-M3G-L44-E Wi-Fi module:
    • 802.11 b/g/n Compatible based on Broadcom MAC/Baseband/Radio device
    • Fully contained TCP/IP stack
    • Host interface: SPI up to 25 MHz
    • Network features ICMP ( Ping), ARP, DHCP,TCP, UDP
    • Low power operation (3.3 V supply) with built-in low power modes
    • Secure Wi-Fi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK
    • CE certified
    • FCC certified
    • IC certified
  • RoHS and China RoHS compliant
  • WEEE compliant

さらに表示

画像

Image
Image

注目リソース

Schematics BOM Gerber
00 ファイルがダウンロード用に選択されています

技術文書

    • 概要 バージョン サイズ アクション
      AN576
      PCB layout optimisation
      3.0
      109.53 KB
      PDF
      AN2484
      STOTG04 in power down mode
      1.2
      669.19 KB
      PDF
      AN316
      Transil™ clamping protection mode
      4.3
      432.1 KB
      PDF
      AN4871
      USB Type-C protection and filtering
      2.1
      2.42 MB
      PDF
      AN5225
      USB Type-C™ Power Delivery using STM32xx Series MCUs and STM32xxx Series MPUs
      2.1
      1.84 MB
      PDF
      AN576

      PCB layout optimisation

      AN2484

      STOTG04 in power down mode

      AN316

      Transil™ clamping protection mode

      AN4871

      USB Type-C protection and filtering

      AN5225

      USB Type-C™ Power Delivery using STM32xx Series MCUs and STM32xxx Series MPUs

    • 概要 バージョン サイズ アクション
      TA0356
      USB Type-C™ and Power Delivery DisplayPort Alternate Mode
      1.0
      6.03 MB
      PDF
      TA0356

      USB Type-C™ and Power Delivery DisplayPort Alternate Mode

    • 概要 バージョン サイズ アクション
      UM2473
      Managing the dynamic input power with the STUSB4500 and the STM32F072RB
      2.0
      1.08 MB
      PDF
      UM2473

      Managing the dynamic input power with the STUSB4500 and the STM32F072RB

プレゼンテーション & トレーニング資料

    • 概要 バージョン サイズ アクション
      STM32 and STM8 embedded software solutions 7.0
      3.12 MB
      PDF
      STM32 for USB Type-C applications 1.0
      2.56 MB
      PDF
      STM32 solutions for USB-C™ & Power Delivery 1.1
      843.01 KB
      PDF
      USB type-C Power Delivery advanced protection fundamentals 1.0
      396.47 KB
      PDF
      USB type-C™ advanced protection solutions quick start guide 2.0
      1.31 MB
      PDF
      USB type-C™ datalines and 'alternate mode' advanced protection fundamentals 1.0
      657.2 KB
      PDF

      STM32 and STM8 embedded software solutions

      STM32 for USB Type-C applications

      STM32 solutions for USB-C™ & Power Delivery

      USB type-C Power Delivery advanced protection fundamentals

      USB type-C™ advanced protection solutions quick start guide

      USB type-C™ datalines and 'alternate mode' advanced protection fundamentals

関連資料

    • 概要 バージョン サイズ アクション
      Power Delivery Protection - Simply cancel ESD and EOS events 1.0
      794.98 KB
      PDF
      Power your device with USB PD! 1.0
      1.18 MB
      PDF
      ST Protection Finder - The new app for Android and iOS 1.0
      1.52 MB
      PDF
      Ultra-low clamping voltage 0201 ESD diodes 1.0
      826.44 KB
      PDF

      Power Delivery Protection - Simply cancel ESD and EOS events

      Power your device with USB PD!

      ST Protection Finder - The new app for Android and iOS

      Ultra-low clamping voltage 0201 ESD diodes

    • 概要 バージョン サイズ アクション
      Power Management Guide 06.2019
      3.86 MB
      PDF
      ST’s solutions for mobile devices 3.2
      2.35 MB
      PDF

      Power Management Guide

      ST’s solutions for mobile devices

設計ツール

    • 製品型番

      Transient voltage suppressor smart selection tool

開発ツール・ハードウェア

    • 製品型番

      Protection product finder application for Android and iOS

      STM32Cube initialization code generator

      Monitoring and configuration software tool for STM32 USB-C and Power Delivery 3.0 applications

ソフトウェア製品

    • 製品型番

      STM32Cube MCU Package for STM32G0 series (HAL, Low-Layer APIs and CMSIS (CORE, DSP, RTOS), USB PD, File system, RTOS) - coming with examples running on ST boards: STM32 Nucleo, Discovery kits and Evaluation boards)

      STM32Cube MCU Package for STM32G4 series (HAL, Low-Layer APIs and CMSIS (CORE, DSP, RTOS), USB, File system, RTOS, Graphic - coming with examples running on ST boards: STM32 Nucleo, Discovery kits and Evaluation boards)

      STM32F105/7, STM32F2 and STM32F4 USB on-the-go Host and device library (UM1021)

      STM32F10x, STM32L1xx and STM32F3xx USB full speed device library (UM0424)

      USB Type-C and Power Delivery software expansion for STM32Cube (UM2073)

評価ツール

    • 製品型番

      USB Power Delivery evaluation board using STM32F072 Type-C Port Manager with FUSB307B Type-C Port Controller from ON Semiconductor

EMI Filtering and Signal Conditioning

品名 概要
ECMF02-2AMX6 Common-mode filter and ESD protection for USB 2.0 and MIPI/MDDI interfaces
ECMF04-4HSWM10 Common mode filter with ESD protection for High Speed Serial interfaces
品名
Common-mode filter and ESD protection for USB 2.0 and MIPI/MDDI interfaces
Common mode filter with ESD protection for High Speed Serial interfaces

Interfaces and Transceivers

品名 概要
STUSB1600 USB Type-C controller (with short-to-VBUS protection)
STUSB1602 USB Type-C controller (with Tx/Rx line driver and BMC)
STUSB1700 USB Type-C controller (with short-to-VBUS protection)
STUSB4500 Standalone USB PD controller for power sinking devices
STUSB4710 Stand-alone USB PD controller (with short-to-VBUS protection)
品名
USB Type-C controller (with short-to-VBUS protection)
USB Type-C controller (with Tx/Rx line driver and BMC)
USB Type-C controller (with short-to-VBUS protection)
Standalone USB PD controller for power sinking devices
Stand-alone USB PD controller (with short-to-VBUS protection)

Microcontrollers & Microprocessors

品名 概要
STM32F072CB Mainstream ARM Cortex-M0 USB line MCU with 128 Kbytes Flash, 48 MHz CPU, USB, CAN and CEC functions
STM32G071GB Mainstream Arm Cortex-M0+ MCU with 128 Kbytes of Flash memory, 36 Kbytes RAM, 64 MHz CPU, 4x USART, timers, ADC, DAC, comm. I/F including USB Type-C and Power Delivery , 1.7-3.6V
STM32G431KB Mainstream Arm Cortex-M4 core with DSP and FPU, 170MHz with 128Kbytes of Flash memory, Math Accelerator, Medium Analog level integration and various comm Interfaces including USB FS 2.0 , USB Type-C and Power Delivery, CAN-FD
品名
Mainstream ARM Cortex-M0 USB line MCU with 128 Kbytes Flash, 48 MHz CPU, USB, CAN and CEC functions
Mainstream Arm Cortex-M0+ MCU with 128 Kbytes of Flash memory, 36 Kbytes RAM, 64 MHz CPU, 4x USART, timers, ADC, DAC, comm. I/F including USB Type-C and Power Delivery , 1.7-3.6V
Mainstream Arm Cortex-M4 core with DSP and FPU, 170MHz with 128Kbytes of Flash memory, Math Accelerator, Medium Analog level integration and various comm Interfaces including USB FS 2.0 , USB Type-C and Power Delivery, CAN-FD

Protection Devices

品名 概要
ESDA25P35-1U1M High-power transient voltage suppressor (TVS)
ESDA7P120-1U1M High-power transient voltage supressor (TVS)
ESDAL DUAL TRANSIL ARRAY FOR ESD PROTECTION
HSP051-4M10 4-line ESD protection for high speed lines
HSP053-4M5 4-line ESD protection for high-speed lines
TCPP01-M12 USB type-C port protection
USBLC6-2SC6Y Automotive very low capacitance ESD protection
品名
High-power transient voltage suppressor (TVS)
High-power transient voltage supressor (TVS)
DUAL TRANSIL ARRAY FOR ESD PROTECTION
4-line ESD protection for high speed lines
4-line ESD protection for high-speed lines
USB type-C port protection
Automotive very low capacitance ESD protection
サポート & フィードバック