ファン

主な特徴

• Half-bridge configuration
• High voltage rail up to 600 V
• Includes samples of each compatible gate driver in SO8 package
  • L6385E, L6387E, L6388E, L6389E,
  • L6395, L6398, L6399
• Compatible with MOSFETs/IGBTs in
  • DPAK, D2PAK, TO-220, TO-220FP
• dV/dt transient immunity ± 50 V/ns in full temperature range
• Integrated bootstrap diode
• Dedicated high- and low-side driving inputs
• Compact and simplified layout
• Gate drivers in the kit features different functionalities and characteristics
  • UVLO on both - high-side and low-side
  • Internal deadtime, or no deadtime
  • Interlocking for anti cross-conduction protection
  • Ability to drive asymmetrical half-bridges and switched reluctance motors
  • Active high or active low LIN for single input gate driving

さらに表示

主な特徴

• Complete 100 W power inverter solution
• HV supply: 90 to 285 V AC or direct DC at 125 to 400 V DC
• Input inrush limiter based on NTC resistor
• Single shunt resistor current-sensing method
• Overtemperature and overcurrent hardware protection
• Compact and safe design
• Test points available to allow further evaluation
• RoHS compliant

さらに表示

主な特徴

• Extended AC input mains range: 115 or 230 VAC nominal at 50/60 Hz, or DC input voltage between 150 and 350 VDC
• Output current: 0.5 A_RMS to the motor
• Power stage: 3-phase inverter bridge implemented using the STGIPN3H60 SLLIMM-nano intelligent power module
• RoHS compliant

さらに表示

主な特徴

• Maximum input voltage: 265 V AC or 375 V DC
• Minimum input voltage: 90 V AC or 128 V DC
• Output power for applied motor: up to 50 W
• +15 V auxiliary power supply based on the VIPER16 in a non-isolated buck configuration
• Compact design using the SLLIMM™-nano STGIPN3H60 consisting of 600 V IGBTs with gate drivers, op amp for current sensing and comparator
• Passive PFC circuit for power factor correction
• On-board infrared (IR) receiver/demodulator for speed and on/off control using IR remote
• External EEPROM M24C01 for recovery of last speed setting
• Hardware overcurrent protection
• Overtemperature protection with NTC thermistor
• Overvoltage and undervoltage detection
• Based on 32-bit ARM^® Cortex™-M3 core-based microcontroller STM32F100C6T6B
• Firmware based on STM32 PMSM FOC SDK 3.0 motor control firmware library and fully customized for the ceiling fan application
• FOC (field oriented control) sensorless algorithm
• PCB size customized for ceiling fan design
• PCB diameter: 105 mm
• Double-sided layout
• RoHS compliant

さらに表示

主な特徴

• Nominal power: up to 100 W
• Compatible with 3.3 V and 5 V control board
• Single shunt resistor for current reading
• On-board temperature sensor
• Overcurrent protection with boost/disabling capability
• For six-step drives:
  • Current limitation/regulation network
  • BEMF detection network
• MC connector
• Compatible with sinusoidal and trapezoidal control
• RoHS compliant

さらに表示

主な特徴

• Wide-range input voltage (30-270 Vac)
• Maximum power up to 100 W at 230 Vac input
• Based on the STGIPN3H60A SLLIMM™-nano AC motor drive
• Mounts the VIPer06 fixed frequency offline converter from the VIPer™ plus family
• Efficient DC-DC power supply (15 V, 3.3 V)
• DC bus voltage power supply connectors
• External 15 V input
• Dedicated connector for interfacing with the various other ST evaluation boards
• Suitable for sinusoidal FOC drives
• Selectable single or three-shunt current reading topology with fast operational amplifier
• Configurable for direct motor current sampling from shunt resistors
• Hardware overcurrent detecting network
• Temperature sensor
• Hall sensor/quadrature encoder inputs
• RoHS compliant

さらに表示

主な特徴

• Minimum input voltage: 125 VDC or 90 VAC
• Maximum input voltage: 400 VDC or 285 VAC
• Input voltage range with applied input voltage doubler from 65 VAC to 145 VAC
• Voltage range for low-voltage motor control applications from 18 VDC to 35 VDC
• Possibility to use auxiliary +15 V supply voltage
• Maximum output power for motors: up to 1 kW
• Regenerative brake control
• Input inrush limitation with bypass relay
• + 15 V auxiliary power supply based on buck converter with VIPer16
• IGBT power switch STGP10H60DF in a TO- 220 package - compatible with other ST IGBTs or power MOSFETs in the TO-220 package
• Fully populated board design with test points and isolated plastic cover for safety
• Motor control connector for interface with the STM3210B-EVAL board and other ST motor control dedicated kits
• Tachometer input
• Hall/encoder inputs
• Possibility to connect BEMF daughterboard for sensorless six-step control of BLDC motors
• PCB type and size:
  • PCB material: FR-4
  • Double-sided layout
  • Copper thickness: 60 μm
  • Total dimensions of board: 127 mm x 180 mm
• RoHS compliant

さらに表示

主な特徴

• High voltage rail up to 600 V
• dV/dt immunity: 50 V/ns in full temperature range
• Driver current capability: 4 A source/sink
• Comparator for fault protections
• Smart shutdown function
• Integrated bootstrap diode
• Adjustable deadtime
• Interlocking function
• Switching times 15 ns rise/fall with 1 nF load
• 3.3 V, 5 V TTL/CMOS inputs with hysteresis
• Compact and simplified layout
• Bill of material reduction
• Effective fault protection
• Flexible, easy and fast design

さらに表示

主な特徴

• Input voltage: 125 - 400 V_DC
• Nominal power: up to 500 W
• Nominal current: up to 3.0 A
• Input auxiliary voltage: up to 20 V DC
• Single or three-shunt resistors for current sensing (with sensing network)
• Two options for current sensing: dedicated op-amps or through MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Uses the STGIF5CH60TS-L IGBT intelligent power module from the 2^nd series of SLLIMM™ IPMs
• 32-pin motor control connector for interfacing with ST MCU boards
• Universal conception for further evaluation with breadboard and testing pins
• Very compact size
• RoHS compliant

さらに表示