バルブ制御

検索履歴

ブックマーク

Please log in to show your saved searches.

概要

ソリューション

HW評価ツール

リソース

ツール & ソフトウェア

主要製品

Get Started

クイックリンク

バルブは、開閉操作や部分的に流路を塞ぐ操作により、媒体（ガス、液体、顆粒、流動固体）の流れを調節します。一般的に2種類のバルブが使用されています。1つは遮断弁で、開または閉のどちらかの状態にしかできません。もう1つは連続的に調整可能な弁で、比例弁や絞り弁などがあります。

電子式バルブ制御ソリューションの設計上、考慮すべき重要な要素は、サイズ、エネルギー効率、信頼性です。

STは、MOSFET、IGBT、トライアックなどの幅広いディスクリート･パワー･スイッチや、インテリジェント･パワー･モジュール（IPM）、モノリシック･インテリジェント･パワー･スイッチ（IPS）、モータ･ドライバ、多種にわたる32bitマイクロコントローラSTM32、湿度/温度センサ、通信ソリューションの提供により、高効率のバルブ設計をサポートしています。

MOSFET and IGBT Drivers

SLLIMM Intelligent Power Modules

Triacs

Intelligent Power Switches

MOSFET and IGBT Drivers

製品型番	概要
STEVAL-IFP010V3	High-side driver based on the VNI2140J	Quick view 主な特徴 Output current: 1 A per channel Shorted-load protection Junction overtemperature protection Case overtemperature protection for thermal independence of the channels Non-simultaneous TCSD (thermal case shutdown) restart for the various channels Protection against loss of ground Current limitation Undervoltage shutdown Open load in off-state and short to V_CC detection Open-drain diagnostic outputs 3.3 V CMOS/TTL compatible inputs Fast demagnetization of inductive loads Conforms to IEC 61131-2 supply voltage: +4 V to +36 V RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-ISA095V1	Up to 3 A step-down switching regulator based on the ST1S14	Quick view 主な特徴 3 A DC output current Operating input voltage from 5.5 V to 48 V 850 kHz internally fixed switching frequency Internal soft-start Internal current limiting Inhibit for zero current consumption 2 mA maximum quiescent current over-temperature range Thermal shutdown RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IHM036V1	Low power motor control board featuring the SLLIMM™ STGIPN3H60 and MCU STM32F100C6T6B	Quick view 主な特徴 Complete 100 W power inverter solution HV supply: 90 to 285 V AC or direct DC at 125 to 400 V DC Input inrush limiter based on NTC resistor Single shunt resistor current-sensing method Overtemperature and overcurrent hardware protection Compact and safe design Test points available to allow further evaluation RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IFP020V1	High side driver based on L6370Q	Quick view 主な特徴 Single-channel topology Galvanic isolation 2.5 A output current 9.5 V to 35 V supply voltage range Short-circuit, overload, and thermal protections Loss of ground and V_S protections Fast demagnetization of inductive loads Open load, output short to V_S detection Two diagnostic outputs Output status LED driver EMC immunity against burst, surge, and ESD RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-ISA099V1	3 A step-down switching demonstration board based on the L7986 in DFN10 package	Quick view 主な特徴 3 A DC output current From 4.5 V to 38 V range input voltage Output voltage adjustable from 0.6 V 250 kHz switching frequency programmable up to 1 MHz Internal soft-start and enable Low dropout operation: 100% duty cycle Voltage feed-forward Zero load current operation Overcurrent and thermal protection RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IHM040V1	BLDC/PMSM driver demonstration board based on STM32 and the SLLIMM nano™	Quick view 主な特徴 Extended AC input mains range: 115 or 230 VAC nominal at 50/60 Hz, or DC input voltage between 150 and 350 VDC Output current: 0.5 A_RMS to the motor Power stage: 3-phase inverter bridge implemented using the STGIPN3H60 SLLIMM-nano intelligent power module RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM
STEVAL-IFP022V1	Eight-channel high-side driver based on the VNI8200XP	Quick view 主な特徴 Operating voltage: from 10.5 to 33 V Operating current: 0.7 A for each channel Reverse polarity protection High-speed opto-isolation for SPI and parallel communication Low-speed opto-isolation for device fault signaling Step-down converter for 3.3 V or 5 V Digital supply voltage LED matrix for channel status signaling Microcontroller interface Designed to meet EMC standard requirements: IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5 RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IHM035V2	3-phase high voltage inverter power board for FOC and scalar motor control based on the STGIPN3H60 (SLLIMM™-nano)	Quick view 主な特徴 Nominal power: up to 100 W Compatible with 3.3 V and 5 V control board Single shunt resistor for current reading On-board temperature sensor Overcurrent protection with boost/disabling capability For six-step drives: Current limitation/regulation network BEMF detection network MC connector Compatible with sinusoidal and trapezoidal control RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IFP015V2	ISO8200B High Side Driver - 8 Channels evaluation board	Quick view 主な特徴 V_CC operating voltage from 10.5 to 33 V 0.7 A for each channel Reverse polarity protection on V_CC and V_DD supply voltage Digital supply voltage V_DD 3.3/5 V Microcontroller interface direct/synchronous mode communication Designed to meet requirements of IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5 standards RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IHM045V1	3-phase high voltage inverter power board for FOC based on the STGIPN3H60A (SLLIMM™-nano)	Quick view 主な特徴 Wide-range input voltage (30-270 Vac) Maximum power up to 100 W at 230 Vac input Based on the STGIPN3H60A SLLIMM™-nano AC motor drive Mounts the VIPer06 fixed frequency offline converter from the VIPer™ plus family Efficient DC-DC power supply (15 V, 3.3 V) DC bus voltage power supply connectors External 15 V input Dedicated connector for interfacing with the various other ST evaluation boards Suitable for sinusoidal FOC drives Selectable single or three-shunt current reading topology with fast operational amplifier Configurable for direct motor current sampling from shunt resistors Hardware overcurrent detecting network Temperature sensor Hall sensor/quadrature encoder inputs RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-ISA152V1	3.3 V/3 A high efficiency step down DC-DC converter (VIN= 4.5 to 60 V) based on the L7987	Quick view 主な特徴 3.3 V output voltage 3 A DC output current 4.5 V to 60 V input voltage 500 kHz switching frequency 3.5 ms programmed soft-start VBIAS switch-over for improved efficiency at light load 180° out of phase synchronization available Open drain PGOOD available Auto recovery overcurrent and thermal protection RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-MKI141V2	HTS221 humidity sensor adapter board for standard DIL24 socket (full pinout)	Quick view 主な特徴 Complete HTS221 pinout (SPI & I²C interface) for a standard DIL 24 socket Fully compatible with STEVAL-MKI109V2 motherboard RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-ISA158V1	38 V - 2 A synchronous step-down switching regulator evaluation board based on the A6986	Quick view 主な特徴 4 V to 38 V operating input voltage Low consumption mode or low noise mode 30 µA I_Q at light load (LCM V_OUT = 3.3 V) 5 µA I_Q-SHTDWN Adjustable f_SW (250 kHz - 2 MHz) Output voltage adjustable from 0.85 V to V_IN Embedded output voltage supervisor Synchronization Adjustable soft-start time Internal current limiting Overvoltage protection Output voltage sequencing Peak current mode architecture R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ Thermal shutdown RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
X-NUCLEO-IHM06A1	Low voltage stepper motor driver expansion board based on the STSPIN220 for STM32 Nucleo	Quick view 主な特徴 Low voltage range: 1.8 to 10 V Microstep adjustment up to the 256^th step Phase current: up to 1.3 A_RMS Current control with adjustable off-time Full protection overcurrent and short circuit protection Thermal shutdown Compatible with Arduino UNO R3 connector Compatible with STM32 Nucleo boards RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
X-NUCLEO-IDS01A4	Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo	Quick view 主な特徴 STM32 Nucleo expansion board based on the SPSGRF-868 SPGRF-868 characteristics: 868 MHz ETSI-certified module based on low power, low data-rate sub-1 GHz SPIRIT1 transceiver Integrated Balun (BALF-SPI-01D3) Chip antenna Compatible with STM32 Nucleo boards Equipped with Arduino UNO R3 connectors Scalable solution; capable of cascading multiple boards for larger systems Example firmware for point-to-point communication, compatible with STM32Cube firmware RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
X-NUCLEO-IDS01A5	Sub-1 GHz RF expansion board based on the SPSGRF-915 module for STM32 Nucleo	Quick view 主な特徴 STM32 Nucleo expansion board based on the SPSGRF-915 X-NUCLEO-IDS01A5 contains FCC and IC certified module SPSGRF-915 (FCC ID: S9NSPSGRF and IC: 8976C-SPSGRF) SPGRF-915: 915 MHz FCC and IC certified module based on low-power, low-rate sub-1 GHz SPIRIT1 transceiver Integrated Balun (BALF-SPI-01D3) Chip antenna Compatible with STM32 Nucleo boards Equipped with Arduino UNO R3 connectors Scalable solution; can cascade multiple boards for larger systems Example firmware for point-to-point communication, compatible with STM32Cube firmware RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
EVAL6491HB	Demonstration board for L6491 gate driver with smart shut down feature	Quick view 主な特徴 High voltage rail up to 600 V dV/dt immunity: 50 V/ns in full temperature range Driver current capability: 4 A source/sink Comparator for fault protections Smart shutdown function Integrated bootstrap diode Adjustable deadtime Interlocking function Switching times 15 ns rise/fall with 1 nF load 3.3 V, 5 V TTL/CMOS inputs with hysteresis Compact and simplified layout Bill of material reduction Effective fault protection Flexible, easy and fast design さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
X-NUCLEO-IDB05A1	Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo	Quick view 主な特徴 STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF) SPBTLE-RF: Bluetooth Low Energy FCC and IC certified module based on Bluetooth^® SMART 4.1 network processor BlueNRG-MS Integrated Balun (BALF-NRG-01D3) Chip antenna Compatible with STM32 Nucleo boards Equipped with Arduino UNO R3 connector Scalable solution, capable of cascading multiple boards for larger systems Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
X-NUCLEO-OUT01A1	Industrial Digital output expansion board based on ISO8200BQ for STM32 Nucleo	Quick view 主な特徴 Enables industrial programmable logic controller (PLC) capabilities on STM32 Nucleo ISO8200BQ galvanic isolated octal high-side smart power solid state-relay Operating voltage from 10.5 V to 33 V Maximum operating output current per channel I_OUT = 700 mA Status LEDs: Fault, Thermal protection Compatible with Arduino^® UNO R3 connector Compliance with EMC standards: IEC61000-4-2: 8kV Contact Discharge and 15kV Air discharge IEC61000-4-3: 4kV Discharge on output and supply line IEC61000-4-5: 2kV Discharge on output and supply line Compatible with STM32 Nucleo boards RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IFP028V1	Single high side driver based on IPS160H	Quick view 主な特徴 Operating voltage from 8 to 60 V Operating current up to 2.5 A Programmable cut-off delay time Reverse polarity protection Galvanic isolation on PCB Input pins compatible with V_CC rails Green LED for channel ON/OFF status Red LED for common diagnostics on: Open load in OFF state Cut-off Thermal protection Red LED functionality on DIAG pin guaranteed from V_CC = 12 V Microcontroller interface IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5 compliant RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
X-NUCLEO-IHM13A1	Low voltage brush DC motor driver expansion board for STM32 Nucleo based on the STSPIN250	Quick view 主な特徴 Low voltage range from 1.8 V to 10 V Current up to 2.6 A r.m.s. Current control with adjustable off-time Full overcurrent and short circuit protection Thermal shutdown Compatible with Arduino UNO R3 connector Compatible with STM32 Nucleo boards RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IFP034V1	Single high side driver based on IPS161H	Quick view 主な特徴 Operating voltage range: 8 to 60 V Operating current: 0.5 A max Programmable cut-off delay time Reverse polarity protection Galvanic isolation on PCB Input pins compatible with V_CC rails Green LED for channel ON/OFF status Red LED for Common Diagnostics on: open load in OFF state cut-off thermal protection Microcontroller interface Compliant with IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5 RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-FKI915V1	Sub-1GHz transceiver development kit based on S2-LP	Quick view 主な特徴 S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier STM32 Nucleo-64 development board with STM32L152RE MCU Suitable for wireless M-Bus systems Suitable for SigFox applications Associated S2-LP development kit including, documentation, firmware for STM32L and GUI Programmable RF output power up to +27 dBm Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK Air data rate from 0.3 to 500 kbps Excellent performance of receiver sensitivity (up to -130 dBm) Low duty cycle RX/TX operation mode Automatic acknowledgement, retransmission and timeout protocol engine SPI interface for microcontroller USB interface RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
EVALSTDRV600HB8	Demonstration board kit for L638xE and L639x high-voltage gate drivers	Quick view 主な特徴 Half-bridge configuration High voltage rail up to 600 V Includes samples of each compatible gate driver in SO8 package L6385E, L6387E, L6388E, L6389E, L6395, L6398, L6399 Compatible with MOSFETs/IGBTs in DPAK, D2PAK, TO-220, TO-220FP dV/dt transient immunity ± 50 V/ns in full temperature range Integrated bootstrap diode Dedicated high- and low-side driving inputs Compact and simplified layout Gate drivers in the kit features different functionalities and characteristics UVLO on both - high-side and low-side Internal deadtime, or no deadtime Interlocking for anti cross-conduction protection Ability to drive asymmetrical half-bridges and switched reluctance motors Active high or active low LIN for single input gate driving さらに表示製品の詳細データブリーフダウンロード注目リソース Schematics BOM Gerber
STEVAL-IDB007V1M	Evaluation platform based on the SPBTLE-1S module	Quick view 主な特徴 Bluetooth^® SMART board with the SPBTLE-1S certified module based on the BlueNRG-1 Bluetooth low energy system-on-chip Associated BlueNRG-1 development kit SW package including firmware and documentation Up to +5 dBm available output power Bluetooth^® low energy v4.2 compliant, supports master, slave and simultaneous master-and-slave roles Integrated balun which integrates a matching network and harmonics filter SMA connector for antenna or measuring equipment 3 user LEDs 2 user buttons 3D digital accelerometer and 3D digital gyroscope MEMS pressure sensor with embedded temperature sensor Battery holder JTAG debug connector USB to serial bridge for providing I/O channel with the BlueNRG-1 device Jumper for measuring current for BlueNRG-1 only RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IPMNG8Q	600 W motor control power board based on STGIPQ8C60T-HZ SLLIMM™-nano IPM	Quick view 主な特徴 Input voltage: from 125 to 400 V_DC Nominal power: up to 600 W Nominal current: up to 4.8 A_rms Input auxiliary voltage: up to 20 V_DC Single- or three-shunt resistors for current sensing (with sensing network) Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input IGBT intelligent power module: 2^nd series SLLIMM-nano IPM (STGIPQ8C60T-HZ – full molded package) Motor control connector (32 pins) interfacing with ST MCU boards Universal design for further evaluation with bread board and testing pins Very compact size RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IPMNM1N	60 W motor control power board based on STIPN1M50T-H SLLIMM™nano IPM MOSFET	Quick view 主な特徴 Input voltage: from 125 to 400 V_DC Nominal power: up to 60 W Nominal current: up to 0.35 Arms Input auxiliary voltage: up to 20 V_DC Single- or three-shunt resistors for current sensing (with sensing network) Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input Intelligent power module: SLLIMM-nano IPM MOSFET-based (STIPN1M50T-H – full molded package) Motor control connector (32 pins) interfacing with ST MCU boards Universal design for further evaluation with bread board and testing pins Very compact size RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IPMNM2N	100 W motor control power board based on STIPN2M50T-H SLLIMM™nano IPM MOSFET	Quick view 主な特徴 Input voltage: from 125 to 400 V_DC Nominal power: up to 100 W Nominal current: up to 0.6 A_rms Input auxiliary voltage: up to 20 V_DC Single- or three-shunt resistors for current sensing (with sensing network) Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input Intelligent power module: SLLIMM-nano IPM MOSFET-based (STIPN2M50T-H – full molded package) Motor control connector (32 pins) interfacing with ST MCU boards Universal design for further evaluation with bread board and testing pins Very compact size RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IDB008V2	Evaluation platform based on the BlueNRG-2	Quick view 主な特徴 Bluetooth^® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip Associated BlueNRG-2 development kit SW package including firmware and documentation Up to +8 dBm available output power (at antenna connector) Excellent receiver sensitivity (-88 dBm) Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm Bluetooth^® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter SMA connector for antenna or measuring equipment 3 user LEDs 2 user buttons 3D digital accelerometer and 3D digital gyroscope MEMS pressure sensor with embedded temperature sensor RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
X-NUCLEO-IHM17M1	Low voltage three-phase brushless DC motor driver expansion board based on STSPIN233 for STM32 Nucleo	Quick view 主な特徴 Low voltage range from 1.8 V to 10 V Current up to 1.3 A_rms Full overcurrent protection and short-circuit protection Thermal shutdown Compatible with STM32 Nucleo boards Equipped with ST morpho connectors Hall/Encoder motor sensor connector and circuit Potentiometer available for speed regulation RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
EVALKITSTKNX	Miniature transceiver STKNX evaluation and development kit	Quick view 主な特徴 Full KNX twisted pair device development kit based on the STKNX miniature transceiver Controlled by STM32F103 microcontroller 32-bit Cortex^® -M3 - 16 MHz - 128 kB Flash Twisted pair TP1-256 support Compatible with ETS engineering tool software Test firmware already downloaded in the board to demonstrate features Includes originally TAPKO KNX protocol stack KAIstack Supported development environments: AC6 OpenSTM32 (Linux^® , Windows^® and Mac OS-X) or Atollic TrueSTUDIO^® (Linux and Windows) JTAG debug through isolated USB host interface (ST-LINK/V2-1 on-board) Standard serial wire debug (SWD) and JTAG interfaces available on standard HE10 20-pin connector Connectors for extension board compatible with Arduino™ and ST Morpho standards UART through isolated USB host interface for connecting a PC No external supply needed during SW development in “desktop mode” (KNX disconnected), USB supply only Power supply flexibility exploiting whole supplies options offered by STKNX 1 button and 1 LED for KNX programming 4 buttons and 4 LEDs for basic KNX sensors and actuators emulation Optional 32.768 kHz crystal for RTC mode Optional CPU reset control from STKNX STKNX area routed on 2 PCB layers only, for reference layout Compliant with bus family standard EN 50491 Complete reference design suitable to implement products compatibles with KNX standards: CENELEC EN 50090 (EU HBES) CEN EN 13321-1/2 (EU BA) ISO/IEC 14543-3 (World HES) GB/T 20965 (Chinese HBC) ANSI/ASHRAE Standard 135 (USA) Includes optional isolation mode for developing SELV product according to EN 61140 Operating temperature range -40 °C to +85 °C さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-FKI868V2	Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP	Quick view 主な特徴 S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands STM32 Nucleo-64 development board with STM32L0 MCU Suitable for Wireless M-Bus systems Associated S2-LP development kit including, documentation, firmware for STM32L and GUI Programmable RF output power up to +16 dBm Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK Air data rate from 0.3 to 500 kbps Ultra-low power consumption: 6.7 mA RX 10 mA TX @ +10 dBm Excellent performance of receiver sensitivity (up to -130 dBm) Low duty cycle RX/TX operation mode Automatic acknowledgement, retransmission, and timeout protocol engine SPI interface for microcontroller USB interface RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-FKI433V2	Sub-1GHz (430-470 MHz) transceiver development kit based on S2-LP	Quick view 主な特徴 S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF module tuned for 430-470 MHz frequency bands STM32 Nucleo-64 development board with STM32L0 MCU Suitable for wireless M-Bus systems Associated S2-LP development kit including, documentation, firmware for STM32L and GUI Programmable RF output power up to +16 dBm Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK Air data rate from 0.3 to 500 kbps Ultra-low power consumption: 6.7 mA RX 10 mA TX at +10 dBm Excellent performance of receiver sensitivity (up to -130 dBm) Low duty cycle RX/TX operation mode Automatic acknowledgement, retransmission and timeout protocol engine SPI interface for microcontroller USB interface RoHS compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
X-NUCLEO-OUT02A1	Industrial digital output expansion board based on ISO8200AQ for STM32 Nucleo	Quick view 主な特徴 Based on the ISO8200AQ whose main characteristics are: Embedded 4kV galvanic isolation Radio frequency communication between the logic and process sides for maximum noise immunity Very low power dissipation (R_ON(MAX) = 220 mΩ) Fast decay for inductive loads 20 MHz SPI I/F on logic side V_CC power good diagnostics Overload and overheating protections with thermal shutdown and diagnostics QFN-32L (9x11x1 mm) package 10.5 to 33 V operating voltage range Green LED (x8) for output on/off status Red LED for process supply power good fault Red LED for overload and overheating Supply reverse polarity protection EMC compliance according to IEC61000-4-2, IEC61000-4-3, IEC61000-4-5 Compatible with STM32 Nucleo boards Equipped with Arduino™ UNO R3 connectors CE certified RoHS and China RoHS compliant WEEE compliant さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber
STEVAL-IFP005V2	High side driver demonstration board based on the VN751PT	Quick view 主な特徴 RoHS compliant Transil addition between TRIAC A2-G terminals Overvoltage protection is not implemented on the board but some solder pads are available to implement it in two different ways: Free development area with hole matrix available for application breadboard adaptation 3 independent application programsHand dryer with infrared sensor and T1235H-6T switchBathroom fan with humidity sensor and ACS108 switchMulti-entrance room controller with push button and BTB08-600SW switch Capacitive power supply (680 nF capacitor EPCOS B32923C36845 V ±10%Average output current: 16 mAStandby power losses < 0.3 W @ 230 V Two potentiometers for setting sensor sensitivity and TRIAC turn-off delay ICC connector for software adjustment Varistor addition between mains voltage Program selector (U2) さらに表示製品の詳細データブリーフダウンロード画像注目リソース Schematics BOM Gerber

製品型番

STEVAL-IFP010V3

High-side driver based on the VNI2140J

クイック･ビュー

主な特徴

Output current: 1 A per channel
Shorted-load protection
Junction overtemperature protection
Case overtemperature protection for thermal independence of the channels
Non-simultaneous TCSD (thermal case shutdown) restart for the various channels
Protection against loss of ground
Current limitation
Undervoltage shutdown
Open load in off-state and short to V_CC detection
Open-drain diagnostic outputs
3.3 V CMOS/TTL compatible inputs
Fast demagnetization of inductive loads
Conforms to IEC 61131-2 supply voltage: +4 V to +36 V
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-ISA095V1

Up to 3 A step-down switching regulator based on the ST1S14

クイック･ビュー

主な特徴

3 A DC output current
Operating input voltage from 5.5 V to 48 V
850 kHz internally fixed switching frequency
Internal soft-start
Internal current limiting
Inhibit for zero current consumption
2 mA maximum quiescent current over-temperature range
Thermal shutdown
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IHM036V1

Low power motor control board featuring the SLLIMM™ STGIPN3H60 and MCU STM32F100C6T6B

クイック･ビュー

主な特徴

Complete 100 W power inverter solution
HV supply: 90 to 285 V AC or direct DC at 125 to 400 V DC
Input inrush limiter based on NTC resistor
Single shunt resistor current-sensing method
Overtemperature and overcurrent hardware protection
Compact and safe design
Test points available to allow further evaluation
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IFP020V1

High side driver based on L6370Q

クイック･ビュー

主な特徴

Single-channel topology
Galvanic isolation
2.5 A output current
9.5 V to 35 V supply voltage range
Short-circuit, overload, and thermal protections
Loss of ground and V_S protections
Fast demagnetization of inductive loads
Open load, output short to V_S detection
Two diagnostic outputs
Output status LED driver
EMC immunity against burst, surge, and ESD
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-ISA099V1

3 A step-down switching demonstration board based on the L7986 in DFN10 package

クイック･ビュー

主な特徴

3 A DC output current
From 4.5 V to 38 V range input voltage
Output voltage adjustable from 0.6 V
250 kHz switching frequency programmable up to 1 MHz
Internal soft-start and enable
Low dropout operation: 100% duty cycle
Voltage feed-forward
Zero load current operation
Overcurrent and thermal protection
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IHM040V1

BLDC/PMSM driver demonstration board based on STM32 and the SLLIMM nano™

クイック･ビュー

主な特徴

Extended AC input mains range: 115 or 230 VAC nominal at 50/60 Hz, or DC input voltage between 150 and 350 VDC
Output current: 0.5 A_RMS to the motor
Power stage: 3-phase inverter bridge implemented using the STGIPN3H60 SLLIMM-nano intelligent power module
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM

STEVAL-IFP022V1

Eight-channel high-side driver based on the VNI8200XP

クイック･ビュー

主な特徴

Operating voltage: from 10.5 to 33 V
Operating current: 0.7 A for each channel
Reverse polarity protection
High-speed opto-isolation for SPI and parallel communication
Low-speed opto-isolation for device fault signaling
Step-down converter for 3.3 V or 5 V
Digital supply voltage
LED matrix for channel status signaling
Microcontroller interface
Designed to meet EMC standard requirements: IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IHM035V2

3-phase high voltage inverter power board for FOC and scalar motor control based on the STGIPN3H60 (SLLIMM™-nano)

クイック･ビュー

主な特徴

Nominal power: up to 100 W
Compatible with 3.3 V and 5 V control board
Single shunt resistor for current reading
On-board temperature sensor
Overcurrent protection with boost/disabling capability
For six-step drives:
- Current limitation/regulation network
- BEMF detection network
MC connector
Compatible with sinusoidal and trapezoidal control
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IFP015V2

ISO8200B High Side Driver - 8 Channels evaluation board

クイック･ビュー

主な特徴

V_CC operating voltage from 10.5 to 33 V
0.7 A for each channel
Reverse polarity protection on V_CC and V_DD supply voltage
Digital supply voltage V_DD 3.3/5 V
Microcontroller interface direct/synchronous mode communication
Designed to meet requirements of IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5 standards
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IHM045V1

3-phase high voltage inverter power board for FOC based on the STGIPN3H60A (SLLIMM™-nano)

クイック･ビュー

主な特徴

Wide-range input voltage (30-270 Vac)
Maximum power up to 100 W at 230 Vac input
Based on the STGIPN3H60A SLLIMM™-nano AC motor drive
Mounts the VIPer06 fixed frequency offline converter from the VIPer™ plus family
Efficient DC-DC power supply (15 V, 3.3 V)
DC bus voltage power supply connectors
External 15 V input
Dedicated connector for interfacing with the various other ST evaluation boards
Suitable for sinusoidal FOC drives
Selectable single or three-shunt current reading topology with fast operational amplifier
Configurable for direct motor current sampling from shunt resistors
Hardware overcurrent detecting network
Temperature sensor
Hall sensor/quadrature encoder inputs
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-ISA152V1

3.3 V/3 A high efficiency step down DC-DC converter (VIN= 4.5 to 60 V) based on the L7987

クイック･ビュー

主な特徴

3.3 V output voltage
3 A DC output current
4.5 V to 60 V input voltage
500 kHz switching frequency
3.5 ms programmed soft-start
VBIAS switch-over for improved efficiency at light load
180° out of phase synchronization available
Open drain PGOOD available
Auto recovery overcurrent and thermal protection
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-MKI141V2

HTS221 humidity sensor adapter board for standard DIL24 socket (full pinout)

クイック･ビュー

STEVAL-ISA158V1

38 V - 2 A synchronous step-down switching regulator evaluation board based on the A6986

クイック･ビュー

主な特徴

4 V to 38 V operating input voltage
Low consumption mode or low noise mode
30 µA I_Q at light load (LCM V_OUT = 3.3 V)
5 µA I_Q-SHTDWN
Adjustable f_SW (250 kHz - 2 MHz)
Output voltage adjustable from 0.85 V to V_IN
Embedded output voltage supervisor
Synchronization
Adjustable soft-start time
Internal current limiting
Overvoltage protection
Output voltage sequencing
Peak current mode architecture
R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
Thermal shutdown
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

X-NUCLEO-IHM06A1

Low voltage stepper motor driver expansion board based on the STSPIN220 for STM32 Nucleo

クイック･ビュー

主な特徴

Low voltage range: 1.8 to 10 V
Microstep adjustment up to the 256^th step
Phase current: up to 1.3 A_RMS
Current control with adjustable off-time
Full protection overcurrent and short circuit protection
Thermal shutdown
Compatible with Arduino UNO R3 connector
Compatible with STM32 Nucleo boards
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

X-NUCLEO-IDS01A4

Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo

クイック･ビュー

主な特徴

STM32 Nucleo expansion board based on the SPSGRF-868
SPGRF-868 characteristics:
- 868 MHz ETSI-certified module based on low power, low data-rate sub-1 GHz SPIRIT1 transceiver
- Integrated Balun (BALF-SPI-01D3)
- Chip antenna
Compatible with STM32 Nucleo boards
Equipped with Arduino UNO R3 connectors
Scalable solution; capable of cascading multiple boards for larger systems
Example firmware for point-to-point communication, compatible with STM32Cube firmware
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

X-NUCLEO-IDS01A5

Sub-1 GHz RF expansion board based on the SPSGRF-915 module for STM32 Nucleo

クイック･ビュー

主な特徴

STM32 Nucleo expansion board based on the SPSGRF-915
X-NUCLEO-IDS01A5 contains FCC and IC certified module SPSGRF-915 (FCC ID: S9NSPSGRF and IC: 8976C-SPSGRF)
SPGRF-915:
- 915 MHz FCC and IC certified module based on low-power, low-rate sub-1 GHz SPIRIT1 transceiver
- Integrated Balun (BALF-SPI-01D3)
- Chip antenna
Compatible with STM32 Nucleo boards
Equipped with Arduino UNO R3 connectors
Scalable solution; can cascade multiple boards for larger systems
Example firmware for point-to-point communication, compatible with STM32Cube firmware
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

EVAL6491HB

Demonstration board for L6491 gate driver with smart shut down feature

クイック･ビュー

主な特徴

High voltage rail up to 600 V
dV/dt immunity: 50 V/ns in full temperature range
Driver current capability: 4 A source/sink
Comparator for fault protections
Smart shutdown function
Integrated bootstrap diode
Adjustable deadtime
Interlocking function
Switching times 15 ns rise/fall with 1 nF load
3.3 V, 5 V TTL/CMOS inputs with hysteresis
Compact and simplified layout
Bill of material reduction
Effective fault protection
Flexible, easy and fast design

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

X-NUCLEO-IDB05A1

Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo

クイック･ビュー

主な特徴

STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
SPBTLE-RF:
- Bluetooth Low Energy FCC and IC certified module based on Bluetooth^® SMART 4.1 network processor BlueNRG-MS
- Integrated Balun (BALF-NRG-01D3)
- Chip antenna
Compatible with STM32 Nucleo boards
Equipped with Arduino UNO R3 connector
Scalable solution, capable of cascading multiple boards for larger systems
Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

X-NUCLEO-OUT01A1

Industrial Digital output expansion board based on ISO8200BQ for STM32 Nucleo

クイック･ビュー

主な特徴

Enables industrial programmable logic controller (PLC) capabilities on STM32 Nucleo
ISO8200BQ galvanic isolated octal high-side smart power solid state-relay
Operating voltage from 10.5 V to 33 V
Maximum operating output current per channel I_OUT = 700 mA
Status LEDs: Fault, Thermal protection
Compatible with Arduino^® UNO R3 connector
Compliance with EMC standards:
- IEC61000-4-2: 8kV Contact Discharge and 15kV Air discharge
- IEC61000-4-3: 4kV Discharge on output and supply line
- IEC61000-4-5: 2kV Discharge on output and supply line
Compatible with STM32 Nucleo boards
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IFP028V1

Single high side driver based on IPS160H

クイック･ビュー

主な特徴

Operating voltage from 8 to 60 V
Operating current up to 2.5 A
Programmable cut-off delay time
Reverse polarity protection
Galvanic isolation on PCB
Input pins compatible with V_CC rails
Green LED for channel ON/OFF status
Red LED for common diagnostics on:
- Open load in OFF state
- Cut-off
- Thermal protection
- Red LED functionality on DIAG pin guaranteed from V_CC = 12 V
Microcontroller interface
IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5 compliant
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

X-NUCLEO-IHM13A1

Low voltage brush DC motor driver expansion board for STM32 Nucleo based on the STSPIN250

クイック･ビュー

主な特徴

Low voltage range from 1.8 V to 10 V
Current up to 2.6 A r.m.s.
Current control with adjustable off-time
Full overcurrent and short circuit protection
Thermal shutdown
Compatible with Arduino UNO R3 connector
Compatible with STM32 Nucleo boards
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IFP034V1

Single high side driver based on IPS161H

クイック･ビュー

主な特徴

Operating voltage range: 8 to 60 V
Operating current: 0.5 A max
Programmable cut-off delay time
Reverse polarity protection
Galvanic isolation on PCB
Input pins compatible with V_CC rails
Green LED for channel ON/OFF status
Red LED for Common Diagnostics on:
- open load in OFF state
- cut-off
- thermal protection
Microcontroller interface
Compliant with IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-FKI915V1

Sub-1GHz transceiver development kit based on S2-LP

クイック･ビュー

主な特徴

S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
STM32 Nucleo-64 development board with STM32L152RE MCU
Suitable for wireless M-Bus systems
Suitable for SigFox applications
Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
Programmable RF output power up to +27 dBm
Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
Air data rate from 0.3 to 500 kbps
Excellent performance of receiver sensitivity (up to -130 dBm)
Low duty cycle RX/TX operation mode
Automatic acknowledgement, retransmission and timeout protocol engine
SPI interface for microcontroller
USB interface
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

EVALSTDRV600HB8

Demonstration board kit for L638xE and L639x high-voltage gate drivers

クイック･ビュー

主な特徴

Half-bridge configuration
High voltage rail up to 600 V
Includes samples of each compatible gate driver in SO8 package
- L6385E, L6387E, L6388E, L6389E,
- L6395, L6398, L6399
Compatible with MOSFETs/IGBTs in
- DPAK, D2PAK, TO-220, TO-220FP
dV/dt transient immunity ± 50 V/ns in full temperature range
Integrated bootstrap diode
Dedicated high- and low-side driving inputs
Compact and simplified layout
Gate drivers in the kit features different functionalities and characteristics
- UVLO on both - high-side and low-side
- Internal deadtime, or no deadtime
- Interlocking for anti cross-conduction protection
- Ability to drive asymmetrical half-bridges and switched reluctance motors
- Active high or active low LIN for single input gate driving

さらに表示

製品の詳細データブリーフダウンロード

注目リソース

Schematics BOM Gerber

STEVAL-IDB007V1M

Evaluation platform based on the SPBTLE-1S module

クイック･ビュー

主な特徴

Bluetooth^® SMART board with the SPBTLE-1S certified module based on the BlueNRG-1 Bluetooth low energy system-on-chip
Associated BlueNRG-1 development kit SW package including firmware and documentation
Up to +5 dBm available output power
Bluetooth^® low energy v4.2 compliant, supports master, slave and simultaneous master-and-slave roles
Integrated balun which integrates a matching network and harmonics filter
SMA connector for antenna or measuring equipment
3 user LEDs
2 user buttons
3D digital accelerometer and 3D digital gyroscope
MEMS pressure sensor with embedded temperature sensor
Battery holder
JTAG debug connector
USB to serial bridge for providing I/O channel with the BlueNRG-1 device
Jumper for measuring current for BlueNRG-1 only
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IPMNG8Q

600 W motor control power board based on STGIPQ8C60T-HZ SLLIMM™-nano IPM

クイック･ビュー

主な特徴

Input voltage: from 125 to 400 V_DC
Nominal power: up to 600 W
Nominal current: up to 4.8 A_rms
Input auxiliary voltage: up to 20 V_DC
Single- or three-shunt resistors for current sensing (with sensing network)
Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
Overcurrent hardware protection
IPM temperature monitoring and protection
Hall sensor or encoder input
IGBT intelligent power module:
- 2^nd series SLLIMM-nano IPM (STGIPQ8C60T-HZ – full molded package)
Motor control connector (32 pins) interfacing with ST MCU boards
Universal design for further evaluation with bread board and testing pins
Very compact size
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IPMNM1N

60 W motor control power board based on STIPN1M50T-H SLLIMM™nano IPM MOSFET

クイック･ビュー

主な特徴

Input voltage: from 125 to 400 V_DC
Nominal power: up to 60 W
Nominal current: up to 0.35 Arms
Input auxiliary voltage: up to 20 V_DC
Single- or three-shunt resistors for current sensing (with sensing network)
Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
Overcurrent hardware protection
IPM temperature monitoring and protection
Hall sensor or encoder input
Intelligent power module:
- SLLIMM-nano IPM MOSFET-based (STIPN1M50T-H – full molded package)
Motor control connector (32 pins) interfacing with ST MCU boards
Universal design for further evaluation with bread board and testing pins
Very compact size
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IPMNM2N

100 W motor control power board based on STIPN2M50T-H SLLIMM™nano IPM MOSFET

クイック･ビュー

主な特徴

Input voltage: from 125 to 400 V_DC
Nominal power: up to 100 W
Nominal current: up to 0.6 A_rms
Input auxiliary voltage: up to 20 V_DC
Single- or three-shunt resistors for current sensing (with sensing network)
Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
Overcurrent hardware protection
IPM temperature monitoring and protection
Hall sensor or encoder input
Intelligent power module:
- SLLIMM-nano IPM MOSFET-based (STIPN2M50T-H – full molded package)
Motor control connector (32 pins) interfacing with ST MCU boards
Universal design for further evaluation with bread board and testing pins
Very compact size
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IDB008V2

Evaluation platform based on the BlueNRG-2

クイック･ビュー

主な特徴

Bluetooth^® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
Associated BlueNRG-2 development kit SW package including firmware and documentation
Up to +8 dBm available output power (at antenna connector)
Excellent receiver sensitivity (-88 dBm)
Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
Bluetooth^® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
SMA connector for antenna or measuring equipment
3 user LEDs
2 user buttons
3D digital accelerometer and 3D digital gyroscope
MEMS pressure sensor with embedded temperature sensor
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

X-NUCLEO-IHM17M1

Low voltage three-phase brushless DC motor driver expansion board based on STSPIN233 for STM32 Nucleo

クイック･ビュー

主な特徴

Low voltage range from 1.8 V to 10 V
Current up to 1.3 A_rms
Full overcurrent protection and short-circuit protection
Thermal shutdown
Compatible with STM32 Nucleo boards
Equipped with ST morpho connectors
Hall/Encoder motor sensor connector and circuit
Potentiometer available for speed regulation
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

EVALKITSTKNX

Miniature transceiver STKNX evaluation and development kit

クイック･ビュー

主な特徴

Full KNX twisted pair device development kit based on the STKNX miniature transceiver
Controlled by STM32F103 microcontroller 32-bit Cortex^® -M3 - 16 MHz - 128 kB Flash
Twisted pair TP1-256 support
Compatible with ETS engineering tool software
Test firmware already downloaded in the board to demonstrate features
Includes originally TAPKO KNX protocol stack KAIstack
Supported development environments: AC6 OpenSTM32 (Linux^® , Windows^® and Mac OS-X) or Atollic TrueSTUDIO^® (Linux and Windows)
JTAG debug through isolated USB host interface (ST-LINK/V2-1 on-board)
Standard serial wire debug (SWD) and JTAG interfaces available on standard HE10 20-pin connector
Connectors for extension board compatible with Arduino™ and ST Morpho standards
UART through isolated USB host interface for connecting a PC
No external supply needed during SW development in “desktop mode” (KNX disconnected), USB supply only
Power supply flexibility exploiting whole supplies options offered by STKNX
1 button and 1 LED for KNX programming
4 buttons and 4 LEDs for basic KNX sensors and actuators emulation
Optional 32.768 kHz crystal for RTC mode
Optional CPU reset control from STKNX
STKNX area routed on 2 PCB layers only, for reference layout
Compliant with bus family standard EN 50491
Complete reference design suitable to implement products compatibles with KNX standards:
- CENELEC EN 50090 (EU HBES)
- CEN EN 13321-1/2 (EU BA)
- ISO/IEC 14543-3 (World HES)
- GB/T 20965 (Chinese HBC)
- ANSI/ASHRAE Standard 135 (USA)
Includes optional isolation mode for developing SELV product according to EN 61140
Operating temperature range -40 °C to +85 °C

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-FKI868V2

Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP

クイック･ビュー

主な特徴

S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
STM32 Nucleo-64 development board with STM32L0 MCU
Suitable for Wireless M-Bus systems
Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
Programmable RF output power up to +16 dBm
Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
Air data rate from 0.3 to 500 kbps
Ultra-low power consumption:
- 6.7 mA RX
- 10 mA TX @ +10 dBm
Excellent performance of receiver sensitivity (up to -130 dBm)
Low duty cycle RX/TX operation mode
Automatic acknowledgement, retransmission, and timeout protocol engine
SPI interface for microcontroller
USB interface
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-FKI433V2

Sub-1GHz (430-470 MHz) transceiver development kit based on S2-LP

クイック･ビュー

主な特徴

S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF module tuned for 430-470 MHz frequency bands
STM32 Nucleo-64 development board with STM32L0 MCU
Suitable for wireless M-Bus systems
Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
Programmable RF output power up to +16 dBm
Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
Air data rate from 0.3 to 500 kbps
Ultra-low power consumption:
- 6.7 mA RX
- 10 mA TX at +10 dBm
Excellent performance of receiver sensitivity (up to -130 dBm)
Low duty cycle RX/TX operation mode
Automatic acknowledgement, retransmission and timeout protocol engine
SPI interface for microcontroller
USB interface
RoHS compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

X-NUCLEO-OUT02A1

Industrial digital output expansion board based on ISO8200AQ for STM32 Nucleo

クイック･ビュー

主な特徴

Based on the ISO8200AQ whose main characteristics are:
- Embedded 4kV galvanic isolation
- Radio frequency communication between the logic and process sides for maximum noise immunity
- Very low power dissipation (R_ON(MAX) = 220 mΩ)
- Fast decay for inductive loads
- 20 MHz SPI I/F on logic side
- V_CC power good diagnostics
- Overload and overheating protections with thermal shutdown and diagnostics
- QFN-32L (9x11x1 mm) package
10.5 to 33 V operating voltage range
Green LED (x8) for output on/off status
Red LED for process supply power good fault
Red LED for overload and overheating
Supply reverse polarity protection
EMC compliance according to IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
Compatible with STM32 Nucleo boards
Equipped with Arduino™ UNO R3 connectors
CE certified
RoHS and China RoHS compliant
WEEE compliant

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

STEVAL-IFP005V2

High side driver demonstration board based on the VN751PT

クイック･ビュー

主な特徴

RoHS compliant
Transil addition between TRIAC A2-G terminals
Overvoltage protection is not implemented on the board but some solder pads are available to implement it in two different ways:
Free development area with hole matrix available for application breadboard adaptation
3 independent application programsHand dryer with infrared sensor and T1235H-6T switchBathroom fan with humidity sensor and ACS108 switchMulti-entrance room controller with push button and BTB08-600SW switch
Capacitive power supply (680 nF capacitor EPCOS B32923C36845 V ±10%Average output current: 16 mAStandby power losses < 0.3 W @ 230 V
Two potentiometers for setting sensor sensitivity and TRIAC turn-off delay
ICC connector for software adjustment
Varistor addition between mains voltage
Program selector (U2)

さらに表示

製品の詳細データブリーフダウンロード

画像

注目リソース

Schematics BOM Gerber

00 ファイルがダウンロード用に選択されています

技術文書

アプリケーションノート

概要	バージョン	サイズ	アクション
AN4607 Basics on the thyristor (SCR) structure and its application	2.0	317.41 KB	PDF
AN4966 Design guidelines for the shutdown function in the SLLIMM-nano series	1.0	1.54 MB	PDF
AN4373 Galvanically-isolated 8 channel high-side driver based on the ISO8200B and ISO8200BQ	2.0	2.02 MB	PDF
AN4030 Gate to cathode capacitor, impact on Triac immunity and reliability	1.0	223.75 KB	PDF
AN4722 HTS221 digital humidity sensor: hardware guidelines for system integration	1.0	844.49 KB	PDF
AN4363 How to select the Triac, ACS, or ACST that fits your application	2.1	361.44 KB	PDF
AN4608 How to select the right thyristor (SCR) for your application	1.0	895.7 KB	PDF
AN4544 IGBT datasheet tutorial	1.1	2.4 MB	PDF
AN2648 Increasing the resolution of analog temperature sensors	1.4	161.7 KB	PDF
AN441 Inductive load control with AC switches	3.2	712.21 KB	PDF
AN4909 Intelligent power switches for 48 V battery applications	1.0	1.07 MB	PDF
AN4564 Is a positive power supply mandatory for my application, or could a negative output work also?	1.0	384.04 KB	PDF
AN994 L638xE application guide	7.1	560.1 KB	PDF
AN1299 L638xE tricks and tips	3.0	718.2 KB	PDF
AN4193 Low duty cycle operation with the SPIRIT1 transceiver	2.0	225.38 KB	PDF
AN4242 New generation of 650 V SiC diodes	2.0	4.75 MB	PDF
AN3168 Non-insulated SCR / Triac control circuits	1.2	315.8 KB	PDF
AN4642 Overview of the BLE Profiles application for X-CUBE-BLE1, expansion for STM32Cube	3.0	2.31 MB	PDF
AN2703 Parameter list for SCRs, TRIACs, AC switches, and DIACS	2.6	98.99 KB	PDF
AN5046 Printed circuit board assembly recommendations for STMicroelectronics PowerFLAT packages	4.0	4.82 MB	PDF
AN440 QII and QIII TRIAC triggering with positive power supply	3.4	97.11 KB	PDF
AN437 RC snubber circuit design for TRIACs	2.6	587.73 KB	PDF
AN533 SCRs, TRIACs, and AC switches, thermal management precautions for handling and mounting	3.6	217.19 KB	PDF
AN4840 SLLIMM™-nano 2nd series small low-loss intelligent molded module	1.0	3.63 MB	PDF
AN4043 SLLIMM™-nano small low-loss intelligent molded module	2.0	8.28 MB	PDF
AN4198 SPIRIT1: increasing the output power	1.0	387.86 KB	PDF
AN2684 STEVAL-IFP006V1: designing with VNI4140K quad high-side smart power solid-state relay ICs	1.2	763.53 KB	PDF
AN4781 STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H	2.0	3.82 MB	PDF
AN4998 STEVAL-IFP034V1 evaluation board for the IPS161H single high side driver	2.0	6.08 MB	PDF
AN4923 STSPIN220: step-mode selection and on-the-fly switching to full-step	1.0	404.43 KB	PDF
AN4999 STSPIN32F0 overcurrent protection	1.0	1.2 MB	PDF
AN439 Snubberless™ and logic level TRIAC behavior at turn-off	3.4	458.5 KB	PDF
AN308 TRIAC analog control circuits for inductive loads	4.2	141.89 KB	PDF
AN442 TRIACS AND MICROCONTROLLERS - THE EASY CONNECTION	2.1	55.99 KB	PDF
AN3169 Technology performance comparison of Triacs subjected to fast transient voltages	1.1	169.53 KB	PDF
AN302 Thyristors and TRIACs: holding current - an important parameter	3.5	138.63 KB	PDF
AN303 Thyristors and TRIACs: latching current	3.4	164.96 KB	PDF
AN4772 wM-Bus (2013) firmware stack overview	1.0	786.08 KB	PDF

AN4607

Basics on the thyristor (SCR) structure and its application

品名	概要
STPSC12065	650 V power Schottky silicon carbide diode
STPSC20065	650 V power Schottky silicon carbide diode
STPSC20H12	1200 V, 20 A High surge Silicon Carbide Power Schottky Diode

品名	概要
BALF-NRG-02D3	50Ω / conjugate match balun to BlueNRG transceiver, with integrated harmonic filter
BALF-SPI-01D3	50Ω nominal input / conjugate match balun to SPIRIT1, with integrated harmonic filter

品名	概要
HTS221	Capacitive digital sensor for relative humidity and temperature
STLM20	Analog temperature sensor, ultra-low current 2.4 V, high precision
STTS751	2.25 V low-voltage local digital temperature sensor

品名	概要
STSPIN220	Low voltage stepper motor driver
STSPIN233	Low voltage three phase and three sense motor driver
STSPIN250	Low voltage brush DC motor driver

品名	概要
IPS160H	Single high-side switch for safety integrity level (SIL2 and SIL3) compliant systems
IPS161H	Single high-side switch for safety integrity level (SIL2 and SIL3) compliant systems
ISO8200B	Galvanic isolated octal high side smart power solid state relay
ISO8200BQ	Galvanic isolated octal high-side smart power solid state-relay
L6370Q	2.5 A single high-side smart power switch
L6491	High voltage high and low-side 4 A gate driver
L6985F	38 V 500 mA synchronous step-down switching regulator with 30 uA quiescent current
L6986	38 V 2 A synchronous step-down switching regulator with 30 uA quiescent current
L6986F	38 V 1.5 A synchronous step-down switching regulator with 30 uA quiescent current
L7985	2A step-down switching regulator
L7986	3A step-down switching regulator
L7987	61 V 3 A asynchronous step-down switching regulator with adjustable current limitation
L7987L	61 V 2 A asynchronous step-down switching regulator with adjustable current limitation
LD39130S	300 mA very low quiescent current Linear regulator IC with automatic Green mode
LDF	1A Very low drop voltage regulator IC
LDFM	500 mA very low drop voltage regulator
LDK120	200 mA low quiescent current very low noise LDO
LDK130	300 mA low quiescent current very low noise LDO
LDK220	200 mA low quiescent current and low noise LDO
LDK320	200 mA low quiescent current and high PSRR voltage regulator
LDL212	1.2A Low Drop Linear Regulator IC
ST1S12XX	Synchronous rectification with inhibit, 0.7 A, 1.7 MHz adjustable, step-down switching regulator
ST1S14	Up to 3 A step down switching regulator
VN751PT	High side driver
VNI2140J	Dual high side smart power solid state relay
VNI4140K	Quad high-side smart power solid-state relay
VNI8200XP	Octal high side smart power solid state relay with serial/parallel selectable interface on chip

品名	概要
STF18N65M5	N-channel 650 V, 0.198 Ohm typ., 15 A MDmesh M5 Power MOSFET in TO-220FP package
STF24N60M2	N-channel 600 V, 0.168 Ohm typ., 18 A MDmesh M2 Power MOSFET in TO-220FP package
STF33N60M2	N-channel 600 V, 0.108 Ohm typ., 26 A MDmesh M2 Power MOSFETs in TO-220FP package
STF34N65M5	N-channel 650 V, 0.09 Ohm typ., 28 A MDmesh M5 Power MOSFET in TO-220FP package
STF7N105K5	N-channel 1050 V, 1.4 Ohm typ., 4 A MDmesh K5 Power MOSFETs in TO-220FP package
STF7N90K5	N-channel 900 V, 0.72 Ohm typ., 7 A MDmesh K5 Power MOSFET in a TO-220FP package
STF8N90K5	N-channel 900 V, 0.60 Ohm typ., 8 A MDmesh K5 Power MOSFET in a TO-220FP package
STL150N3LLH6	N-channel 30 V, 0.0016 Ohm typ., 33 A STripFET(TM) VI DeepGATE(TM) Power MOSFET in PowerFLAT(TM) 5x6 package
STL19N60M2	N-channel 600 V, 0.278 Ohm typ., 11 A MDmesh M2 Power MOSFET in a PowerFLAT 8x8 HV package
STL20N6F7	N-channel 60 V, 0.0046 Ohm typ., 20 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package
STL50N6F7	N-channel 60 V, 9 mOhm typ., 60 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
STW12N150K5	N-channel 1500 V, 1.6 Ohm typ., 7 A MDmesh K5 Power MOSFET in a TO-247 package
STW69N65M5	N-channel 650 V, 0.037 Ohm typ., 58 A MDmesh M5 Power MOSFET in TO-247 package

品名	概要
BlueNRG-2	Bluetooth® low energy wireless system-on-chip
BlueNRG-MS	Bluetooth Low Energy Network Processor supporting Bluetooth 4.2 core specification
S2-LP	Ultra-low power, high performance, sub-1GHz transceiver
SPBTLE-1S	Very low power application module for Bluetooth® Smart v4.2
SPBTLE-RF	Very low power module for Bluetooth Smart v4.1
SPIRIT1	Low data rate, low power Sub 1GHz transceiver
SPSGRF	Sub-GHz (868 or 915 MHz) low power programmable RF transceiver modules
STS1TX	Low data rate, low power sub-1GHz transmitter

概要	バージョン	サイズ	アクション
Intelligent power switches (IPS)	04.2018	627.09 KB	PDF
モータ制御リファレンスガイド	15.11	2.67 MB	PDF
スマート･インダストリ向け製品 & ソリューションガイド	3.1	3.41 MB	PDF

品名	製造元	概要
STSW-BLUENRG-DK	ST	Setup for BlueNRG Kits
STSW-BLUENRG1-DK	ST	BlueNRG-1, BlueNRG-2 DK SW package
STSW-CONNECT009	ST	Setup for SPIRIT1 design kit
STSW-IFP001	--	IPS Evaluation Tool
STSW-IFP015	--	STSW-IFP015 application software setup
STSW-IFP022	--	STSW-IFP022 application software setup
STSW-IFP029GUI	ST	Graphical user interface for the STEVAL-IFP029V1 evaluation board
STSW-POWERSTUDIO	ST	ST PowerStudio dynamic electrothermal simulation software for power devices
STSW-S2LP-SFX-DK	ST	Evaluation SW package based on S2-LP

検索履歴

ブックマーク

ビデオ

技術文書

プレゼンテーション & トレーニング資料

関連資料

ソフトウェア製品

eDesignSuite

Diodes and Rectifiers

EMI Filtering and Signal Conditioning

Interfaces and Transceivers

MEMS and Sensors

Motor Drivers

パワー･マネージメント

Power Transistors

ワイヤレス･トランシーバ / マイコン / モジュール