Window and Roller Shutters

Key Features

• Compact size
• Wide-range input voltage
• Maximum power up to 150 W at 230 Vac input
• STGD3HF60HD: 4.5 A, 600 V very fast IGBT
• Compatibility with other power switches in DPAK packages (the STD5N52U and STGD6NC60HD, for example)
• AC or DC bus voltage power supply connectors
• Connector for interfacing with the STM3210xx-EVAL board, STEVAL-IHM022V1, and STEVAL-IHM033V1 with alternate functions (current reference, current limitation/regulation, method selection, current boost)
• Efficient DC/DC power supply (15 V, 3.3 V)
• Suitable both for sinusoidal FOC and trapezoidal BLDC drive
• Single-shunt current reading topology with fast operational amplifier (with offset insertion for bipolar currents)
• Hardware overcurrent protection with boost capabilities
• Temperature sensor
• BEMF-detection network for BLDC drive
• Current regulation/limitation network for BLDC drive
• Hall sensor/quadrature encoder inputs

Show More

Key Features

• Extended AC input mains range: 115 or 230 VAC nominal at 50/60 Hz, or DC input voltage between 150 and 350 VDC
• Output current: 0.5 A_RMS to the motor
• Power stage: 3-phase inverter bridge implemented using the STGIPN3H60 SLLIMM-nano intelligent power module
• RoHS compliant

Show More

Key Features

• Input voltage: from 125 to 400 V_DC
• Nominal power: up to 60 W
• Nominal current: up to 0.35 Arms
• Input auxiliary voltage: up to 20 V_DC
• Single- or three-shunt resistors for current sensing (with sensing network)
• Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Intelligent power module:
  • SLLIMM-nano IPM MOSFET-based (STIPN1M50T-H – full molded package)
• Motor control connector (32 pins) interfacing with ST MCU boards
• Universal design for further evaluation with bread board and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Nominal power: up to 100 W
• Compatible with 3.3 V and 5 V control board
• Single shunt resistor for current reading
• On-board temperature sensor
• Overcurrent protection with boost/disabling capability
• For six-step drives:
  • Current limitation/regulation network
  • BEMF detection network
• MC connector
• Compatible with sinusoidal and trapezoidal control
• RoHS compliant

Show More

Key Features

• Complete 100 W power inverter solution
• HV supply: 90 to 285 V AC or direct DC at 125 to 400 V DC
• Input inrush limiter based on NTC resistor
• Single shunt resistor current-sensing method
• Overtemperature and overcurrent hardware protection
• Compact and safe design
• Test points available to allow further evaluation
• RoHS compliant

Show More

Key Features

• Wide range input voltage
• Maximum power: up to 100 W at 230 Vac input
• STD5N52U power MOSFET (4.4 A, 520 V)
• Compatible with other power switches in DPAK packages (i.e. the STGD6NC60HD or STGDL6NC60DI)
• 15 V auxiliary power supply connector
• Motor control connector for interfacing with STM32-based control stages
• Three shunt resistor-based motor current sensing network
• Target applications: refrigerator compressors and dishwasher pumps
• RoHS compliant

Show More

Key Features

• Input voltage: from 125 to 400 V_DC
• Nominal power: up to 100 W
• Nominal current: up to 0.6 A_rms
• Input auxiliary voltage: up to 20 V_DC
• Single- or three-shunt resistors for current sensing (with sensing network)
• Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Intelligent power module:
  • SLLIMM-nano IPM MOSFET-based (STIPN2M50T-H – full molded package)
• Motor control connector (32 pins) interfacing with ST MCU boards
• Universal design for further evaluation with bread board and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Wide-range input voltage (30-270 Vac)
• Maximum power up to 100 W at 230 Vac input
• Based on the STGIPN3H60A SLLIMM™-nano AC motor drive
• Mounts the VIPer06 fixed frequency offline converter from the VIPer™ plus family
• Efficient DC-DC power supply (15 V, 3.3 V)
• DC bus voltage power supply connectors
• External 15 V input
• Dedicated connector for interfacing with the various other ST evaluation boards
• Suitable for sinusoidal FOC drives
• Selectable single or three-shunt current reading topology with fast operational amplifier
• Configurable for direct motor current sampling from shunt resistors
• Hardware overcurrent detecting network
• Temperature sensor
• Hall sensor/quadrature encoder inputs
• RoHS compliant

Show More

Key Features

• 3.3 V output voltage
• 3 A DC output current
• 4.5 V to 60 V input voltage
• 500 kHz switching frequency
• 3.5 ms programmed soft-start
• VBIAS switch-over for improved efficiency at light load
• 180° out of phase synchronization available
• Open drain PGOOD available
• Auto recovery overcurrent and thermal protection
• RoHS compliant

Show More

Key Features

• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• 30 µA I_Q at light load (LCM V_OUT = 3.3 V)
• 5 µA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• 3 A DC output current
• From 4.5 V to 38 V range input voltage
• Output voltage adjustable from 0.6 V
• 250 kHz switching frequency programmable up to 1 MHz
• Internal soft-start and enable
• Low dropout operation: 100% duty cycle
• Voltage feed-forward
• Zero load current operation
• Overcurrent and thermal protection
• RoHS compliant

Show More

Key Features

• Features of the PM8805 PoE-PD interface:
  • System in package integrating a double active bridge, a hot-swap MOSFET and a PoE-PD
  • Supports legacy high power, 4-pair applications
  • 100 V N-ch MOSFETs with 0.2 Ω total path resistance for each active bridge
  • Identifies which kind of PSE (standard or legacy) is connected to, and provides successful IEEE802.3 af /at /bt classification indication as combination of the T0, T1 and T2 signals (open drain)
  • Smart operational mode selection through the STBY, FAUX and RAUX control signals
  • QFN 56 8x8mm package with 43 pins and 6 exposed pads
• Features of the PM8804 PWM controller:
  • PWM peak current mode controller
  • Input operating voltage up to 75 V
  • Internal high voltage start up regulator with 20 mA capability
  • Programmable fixed frequency up to 1 Mhz
  • Soft start up with adjustable time
  • Soft turn off (optionally disabled)
  • Dual 1 A_PK , low side complementary gate drivers
  • GATE2 optionally turned off for reduced consumption
  • 80% maximum duty cycle with internal slope compensation
  • QFN 16 3x3mm package with exposed pad

Show More

Key Features

• Buck topology
• Input power consumption:
  • 20 mW at 230 V_AC in no load condition
  • 400 mW at 230 V_AC in 250 mW load
• Input voltage: 60 to 300 V_AC
• Output voltage: 5 V
• Output current: 100 mA
• Switching frequency: 60 kHz with jittering
• Max ambient. temperature: 60 °C
• Automatic restart protections: OLP, short-circuit, VCC clamp, max duty cycle counter, thermal shutdown
• Pulse-skip protection to prevent flux-runaway
• Dimensions: 27 mm x 24 mm
• Meets IEC55022 Class B conducted EMI even with reduced EMI filter, thanks to the frequency jittering feature
• VIPer013B 800V avalanche rugged technology and embedded protections ensure enhanced system reliability
• RoHS compliant

Show More

Key Features

• 3 A DC output current
• Operating input voltage from 5.5 V to 48 V
• 850 kHz internally fixed switching frequency
• Internal soft-start
• Internal current limiting
• Inhibit for zero current consumption
• 2 mA maximum quiescent current over-temperature range
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• ST25TA02K NFC seal
• ST25TA02K NFC stickers
• ST25TA02K key fob
• ST25TA02K NFC bracelet
• ST25TA64K NFC cards
• ST25TA02K NFC Secure paper label

Show More

Key Features

• Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
• Up to 4-Kbit memory with NDEF support
• 54 mm diameter, single layer circular antenna
• Compatible with STM32 Nucleo boards
• Equipped with Arduino™ UNO R3 connector
• Self-powered or powered through the Arduino™ UNO R3 connectors
• Three general purpose LEDs
• Scalable solution, capable of cascading multiple boards for larger systems
• Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
• FCC and IC verified
• RoHS compliant

Show More

Key Features

• M24SR64-Y Dynamic NFC/RFID tag IC
• NFC antenna: 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• Powered through the Arduino UNO R3 connectors
• 3 color LEDs for general purpose

Show More