EVAL6498L Evaluation board for the L6498L gate driver Quick view
主な特徴
Driver current capability: 2 A source, 2.5 A sink Integrated bootstrap diode Interlocking function 3.3 V, 5 V TTL/CMOS inputs with hysteresis UVLO on both high-side and low-side sections dV/dt immunity: 50 V/ns in full temperature range Compact and simplified layout Bill of material reduction Flexible, easy and fast design さらに表示
画像
STEVAL-FKI868V2 Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP Quick view
主な特徴
S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands STM32 Nucleo-64 development board with STM32L0 MCU Suitable for Wireless M-Bus systems Associated S2-LP development kit including, documentation, firmware for STM32L and GUI Programmable RF output power up to +16 dBm Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK Air data rate from 0.3 to 500 kbps Ultra-low power consumption: 6.7 mA RX 10 mA TX @ +10 dBm Excellent performance of receiver sensitivity (up to -130 dBm) Low duty cycle RX/TX operation mode Automatic acknowledgement, retransmission, and timeout protocol engine SPI interface for microcontroller USB interface RoHS compliant さらに表示
画像
STEVAL-ISA152V1 3.3 V/3 A high efficiency step down DC-DC converter (VIN= 4.5 to 60 V) based on the L7987 Quick view
主な特徴
3.3 V output voltage 3 A DC output current 4.5 V to 60 V input voltage 500 kHz switching frequency 3.5 ms programmed soft-start VBIAS switch-over for improved efficiency at light load 180° out of phase synchronization available Open drain PGOOD available Auto recovery overcurrent and thermal protection RoHS compliant さらに表示
画像
STEVAL-IHM028V2 2 kW 3-phase motor control evaluation board featuring the STGIPS20C60 IGBT intelligent power module Quick view
主な特徴
Complete solution for a 2 kW power inverter HV supply mode: voltage 90 VAC to 285 VAC or direct DC line 125 V DC to 400 V DC Input voltage range extended to +400 V, for PFC compliance Input inrush limiter with bypassing relay Brake feature with overvoltage comparator Single- or three-shunt resistor current sensing method Hall sensor or encoder input Tachometer input Overtemperature and overcurrent hardware protection Active fan with automatic overtemperature switching Compact and safe design Universal conception for further evaluation with bread board and testing pins RoHS compliant さらに表示
画像
STEVAL-MKI141V2 HTS221 humidity sensor adapter board for standard DIL24 socket (full pinout) Quick view
主な特徴
Complete HTS221 pinout (SPI & I²C interface) for a standard DIL 24 socket Fully compatible with STEVAL-MKI109V2 motherboard RoHS compliant さらに表示
画像
STEVAL-IHM023V3 1 kW 3-phase motor control evaluation board featuring L6390 drivers and STGP10H60DF IGBT Quick view
主な特徴
Minimum input voltage: 125 VDC or 90 VAC Maximum input voltage: 400 VDC or 285 VAC Input voltage range with applied input voltage doubler from 65 VAC to 145 VAC Voltage range for low-voltage motor control applications from 18 VDC to 35 VDC Possibility to use auxiliary +15 V supply voltage Maximum output power for motors: up to 1 kW Regenerative brake control Input inrush limitation with bypass relay + 15 V auxiliary power supply based on buck converter with VIPer16 IGBT power switch STGP10H60DF in a TO- 220 package - compatible with other ST IGBTs or power MOSFETs in the TO-220 package Fully populated board design with test points and isolated plastic cover for safety Motor control connector for interface with the STM3210B-EVAL board and other ST motor control dedicated kits Tachometer input Hall/encoder inputs Possibility to connect BEMF daughterboard for sensorless six-step control of BLDC motors PCB type and size: PCB material: FR-4 Double-sided layout Copper thickness: 60 μm Total dimensions of board: 127 mm x 180 mm RoHS compliant さらに表示
画像
EVLPOWERSTEP01 System-in-package integrating microstepping controller and 10 A power MOSFETs evaluation board Quick view
主な特徴
Voltage range from 10.5 V to 85 V 10 Ar.m.s. maximum output current Up to 1/128 microstep Programmable speed profile and advanced commands Adjustable output slew rate SPI with daisy chain feature FLAG and BUSY LED indicators Flexible supply voltage management Suitable to be used in combination with STEVAL-PCC009V2 さらに表示
STEVAL-ISA158V1 38 V - 2 A synchronous step-down switching regulator evaluation board based on the A6986 Quick view
主な特徴
4 V to 38 V operating input voltage Low consumption mode or low noise mode 30 µA IQ at light load (LCM VOUT = 3.3 V) 5 µA IQ-SHTDWN Adjustable fSW (250 kHz - 2 MHz) Output voltage adjustable from 0.85 V to VIN Embedded output voltage supervisor Synchronization Adjustable soft-start time Internal current limiting Overvoltage protection Output voltage sequencing Peak current mode architecture RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ Thermal shutdown RoHS compliant さらに表示
画像
X-NUCLEO-IHM08M1 Low-Voltage BLDC motor driver expansion board based on STL220N6F7 for STM32 Nucleo Quick view
主な特徴
3-phase driver board for BLDC/PMSM motors Nominal operating voltage range from 10 V to 48 V DC 15 ARMS output current Operating frequency selectable by firmware Overcurrent detection and protection (30 Apeak ) Thermal monitoring and overheating protection Compatible with STM32 Nucleo boards Equipped with ST morpho connectors 3-Shunt and 1-Shunt configurable jumpers for motor current sensing Hall/Encoder motor sensor connector and circuit Debug connector for DAC, GPIOs, etc. Potentiometer available for speed regulation User LED RoHS compliant さらに表示
画像
X-NUCLEO-IDS01A4 Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo Quick view
主な特徴
STM32 Nucleo expansion board based on the SPSGRF-868 SPGRF-868 characteristics: 868 MHz ETSI-certified module based on low power, low data-rate sub-1 GHz SPIRIT1 transceiver Integrated Balun (BALF-SPI-01D3) Chip antenna Compatible with STM32 Nucleo boards Equipped with Arduino UNO R3 connectors Scalable solution; capable of cascading multiple boards for larger systems Example firmware for point-to-point communication, compatible with STM32Cube firmware RoHS compliant さらに表示
画像
X-NUCLEO-IDS01A5 Sub-1 GHz RF expansion board based on the SPSGRF-915 module for STM32 Nucleo Quick view
主な特徴
STM32 Nucleo expansion board based on the SPSGRF-915 X-NUCLEO-IDS01A5 contains FCC and IC certified module SPSGRF-915 (FCC ID: S9NSPSGRF and IC: 8976C-SPSGRF) SPGRF-915: 915 MHz FCC and IC certified module based on low-power, low-rate sub-1 GHz SPIRIT1 transceiver Integrated Balun (BALF-SPI-01D3) Chip antenna Compatible with STM32 Nucleo boards Equipped with Arduino UNO R3 connectors Scalable solution; can cascade multiple boards for larger systems Example firmware for point-to-point communication, compatible with STM32Cube firmware RoHS compliant さらに表示
画像
EVAL6491HB Demonstration board for L6491 gate driver with smart shut down feature Quick view
主な特徴
High voltage rail up to 600 V dV/dt immunity: 50 V/ns in full temperature range Driver current capability: 4 A source/sink Comparator for fault protections Smart shutdown function Integrated bootstrap diode Adjustable deadtime Interlocking function Switching times 15 ns rise/fall with 1 nF load 3.3 V, 5 V TTL/CMOS inputs with hysteresis Compact and simplified layout Bill of material reduction Effective fault protection Flexible, easy and fast design さらに表示
画像
X-NUCLEO-IDB05A1 Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo Quick view
主な特徴
STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF) SPBTLE-RF: Bluetooth Low Energy FCC and IC certified module based on Bluetooth® SMART 4.1 network processor BlueNRG-MS Integrated Balun (BALF-NRG-01D3) Chip antenna Compatible with STM32 Nucleo boards Equipped with Arduino UNO R3 connector Scalable solution, capable of cascading multiple boards for larger systems Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware RoHS compliant さらに表示
画像
STEVAL-IPM05F 500 W motor control power board based on STGIF5CH60TS-L SLLIMM™ 2nd series IPM Quick view
主な特徴
Input voltage: 125 - 400 VDC Nominal power: up to 500 W Nominal current: up to 3.0 A Input auxiliary voltage: up to 20 V DC Single or three-shunt resistors for current sensing (with sensing network) Two options for current sensing: dedicated op-amps or through MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input Uses the STGIF5CH60TS-L IGBT intelligent power module from the 2nd series of SLLIMM™ IPMs 32-pin motor control connector for interfacing with ST MCU boards Universal conception for further evaluation with breadboard and testing pins Very compact size RoHS compliant さらに表示
画像
STEVAL-IPM10F 1000 W motor control power board based on STGIF10CH60TS-L SLLIMM™ 2nd series IPM Quick view
主な特徴
Input voltage: 125 - 400 VDC Nominal power: up to 1000 W Nominal power: up to 6 A Input auxiliary voltage: up to 20 V DC Single- or three- shunt resistors for current sensing (with sensing network) Two options for current sensing: dedicated op-amps or through MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input Uses the STGIF10CH60TS-L IGBT intelligent power module from the 2nd series of SLLIMM™ IPMs Motor control connector (32-pin) to interface with ST MCU boards Universal conception for further evaluation with breadboard and testing pins Very compact size RoHS compliant さらに表示
画像
STEVAL-IPM10B 1200 W motor control power board based on STGIB10CH60TS-L SLLIMM™ 2nd series IPM Quick view
主な特徴
Input voltage: 125 - 400 VDC Nominal power: up to 1200 W Nominal current: up to 7 A Input auxiliary voltage: up to 20 V DC Single- or three- shunt resistors for current sensing (with sensing network) Two options for current sensing: dedicated op-amps or through MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input Uses the STGIB10CH60TS-L IGBT intelligent power module from the 2nd series of SLLIMM™ IPMs Motor control connector (32-pin) to interface with ST MCU boards Universal conception for further evaluation with breadboard and testing pins Very compact size RoHS compliant さらに表示
画像
STEVAL-IPM15B 1500 W motor control power board based on STGIB15CH60TS-L SLLIMM™ 2nd series IPM Quick view
主な特徴
Input voltage: 125 - 400 VDC Nominal power: up to 1500 W Nominal current: up to 9 A Input auxiliary voltage: up to 20 V DC Single- or three-shunt resistors for current sensing (with sensing network) Two options for current sensing: dedicated op-amps or through MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input Uses the STGIB15CH60TS-L IGBT intelligent power module from the 2nd series of SLLIMM™ IPMs Motor control connector (32-pin) to interface with ST MCU boards Universal conception for further evaluation with breadboard and testing pins Very compact size さらに表示
画像
STEVAL-IPM07F 700 W motor control power board based on STGIF7CH60TS-L SLLIMM™ 2nd series IPM Quick view
主な特徴
Input voltage: 125 - 400 VDC Nominal power: up to 700 W Nominal current: up to 4.2 A Input auxiliary voltage: up to 20 V DC Single or three-shunt resistors for current sensing (with sensing network) Two options for current sensing: dedicated op-amps or through MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input Uses the STGIF7CH60TS-L IGBT intelligent power module from the SLLIMM™ 2nd series IPMs Motor control connector (32-pin) interfacing with ST MCU boards Universal conception for further evaluation with bread board and testing pins Very compact size さらに表示
画像
X-NUCLEO-LED16A1 16 channel LED driver expansion board based on LED1642GW for STM32 Nucleo Quick view
主な特徴
16 constant current output channels Output current: from 3 mA to 40 mA 20 V current generator rated voltage Provision for cascading multiple expansion boards Current adjustment: 7-bit global current gain adjustment in two ranges Current programmable through external resistor 12/16-bit PWM grayscale brightness control Selectable LED Bus voltage supply Error detection Thermal shutdown Compatible with STM32 Nucleo board Equipped with Arduino™ UNO R3 connector RoHS compliant さらに表示
画像
STEVAL-IPM08B 800 W motor control power board based on STGIB8CH60TS-L SLLIMM™ 2nd series IPM Quick view
主な特徴
Input voltage: 125 to 400 VDC Nominal power: up to 800 W Nominal current: up to 4.8 A Input auxiliary voltage: up to 20 VDC Single- or three- shunt resistors for current sensing (with sensing network) Two options for current sensing: dedicated op-amps or through MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input IGBT intelligent power module: 2nd series of SLLIMM IPM (STGIB8CH60TS-L – DBC package) Motor control connector (32 pin) interfacing with ST MCU boards Universal design for further evaluation with bread board and testing pins Very compact size RoHS compliant さらに表示
画像
STEVAL-FKI915V1 Sub-1GHz transceiver development kit based on S2-LP Quick view
主な特徴
S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier STM32 Nucleo-64 development board with STM32L152RE MCU Suitable for wireless M-Bus systems Suitable for SigFox applications Associated S2-LP development kit including, documentation, firmware for STM32L and GUI Programmable RF output power up to +27 dBm Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK Air data rate from 0.3 to 500 kbps Excellent performance of receiver sensitivity (up to -130 dBm) Low duty cycle RX/TX operation mode Automatic acknowledgement, retransmission and timeout protocol engine SPI interface for microcontroller USB interface RoHS compliant さらに表示
画像
EVALSTDRV600HB8 Demonstration board kit for L638xE and L639x high-voltage gate drivers Quick view
主な特徴
Half-bridge configuration High voltage rail up to 600 V Includes samples of each compatible gate driver in SO8 package L6385E, L6387E, L6388E, L6389E, L6395, L6398, L6399 Compatible with MOSFETs/IGBTs in DPAK, D2PAK, TO-220, TO-220FP dV/dt transient immunity ± 50 V/ns in full temperature range Integrated bootstrap diode Dedicated high- and low-side driving inputs Compact and simplified layout Gate drivers in the kit features different functionalities and characteristics UVLO on both - high-side and low-side Internal deadtime, or no deadtime Interlocking for anti cross-conduction protection Ability to drive asymmetrical half-bridges and switched reluctance motors Active high or active low LIN for single input gate driving さらに表示
STEVAL-IDB007V1M Evaluation platform based on the SPBTLE-1S module Quick view
主な特徴
Bluetooth® SMART board with the SPBTLE-1S certified module based on the BlueNRG-1 Bluetooth low energy system-on-chip Associated BlueNRG-1 development kit SW package including firmware and documentation Up to +5 dBm available output power Bluetooth® low energy v4.2 compliant, supports master, slave and simultaneous master-and-slave roles Integrated balun which integrates a matching network and harmonics filter SMA connector for antenna or measuring equipment 3 user LEDs 2 user buttons 3D digital accelerometer and 3D digital gyroscope MEMS pressure sensor with embedded temperature sensor Battery holder JTAG debug connector USB to serial bridge for providing I/O channel with the BlueNRG-1 device Jumper for measuring current for BlueNRG-1 only RoHS compliant さらに表示
画像
STEVAL-IDB008V2 Evaluation platform based on the BlueNRG-2 Quick view
主な特徴
Bluetooth® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip Associated BlueNRG-2 development kit SW package including firmware and documentation Up to +8 dBm available output power (at antenna connector) Excellent receiver sensitivity (-88 dBm) Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm Bluetooth® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter SMA connector for antenna or measuring equipment 3 user LEDs 2 user buttons 3D digital accelerometer and 3D digital gyroscope MEMS pressure sensor with embedded temperature sensor RoHS compliant さらに表示
画像
STEVAL-ILL021V1 LCD panels backlight demonstration board based on the LED7707 Quick view
主な特徴
Features boost section4.5 V to 36 V input voltage rangeinternal power MOSFETinternal +5 V LDO for device supplyup to 36 V output voltageconstant frequency peak current-mode control250 kHz to 1 MHz adjustable switching frequencyexternal sync for multi-device applicationpulse-skip power saving mode at light loadprogrammable soft-startprogrammable OVP protectionsingle ceramic output capacitornon-latched thermal shutdown RoHS compliant Features backlight driver sectionsix rows with 85 mA maximum current capability (adjustable)up to 10 white LEDs per rowrows disable optionless than 10 μs minimum dimming time±2.0% current matching between rowsLED failure (open and short circuit) detection さらに表示
画像
STEVAL-ISA095V1 Up to 3 A step-down switching regulator based on the ST1S14 Quick view
主な特徴
3 A DC output current Operating input voltage from 5.5 V to 48 V 850 kHz internally fixed switching frequency Internal soft-start Internal current limiting Inhibit for zero current consumption 2 mA maximum quiescent current over-temperature range Thermal shutdown RoHS compliant さらに表示
画像
EVAL6470PD Fully integrated stepper motor driver mounting the L6470 in a high power PowerSO package Quick view
主な特徴
Voltage range from 8 V to 45 V Phase current up to 3 Ar.m.s. Dual SPI connector (daisy chain configuration suitable) SW input FLAG and BUSY LED indicators Adjustable supply voltage compensation High thermal performance (Rthj-a 12 °C/W typical) Suitable for use in combination with the STEVAL-PCC009V2 さらに表示
画像
STEVAL-ISA099V1 3 A step-down switching demonstration board based on the L7986 in DFN10 package Quick view
主な特徴
3 A DC output current From 4.5 V to 38 V range input voltage Output voltage adjustable from 0.6 V 250 kHz switching frequency programmable up to 1 MHz Internal soft-start and enable Low dropout operation: 100% duty cycle Voltage feed-forward Zero load current operation Overcurrent and thermal protection RoHS compliant さらに表示
画像
EVAL6472PD Fully integrated stepper motor driver mounting the L6472 in a high power PowerSO package Quick view
主な特徴
Voltage range from 8 V to 45 V Phase current up to 3 Ar.m.s. Dual SPI connector (with daisy chain configuration suitable) SW input FLAG and BUSY LED indicators High thermal performance (Rthj-a 12 °C/W typical) Suitable for use in combination with the STEVAL-PCC009V2 さらに表示
画像
EVAL6480H Fully integrated microstepping motor controller with motion engine and SPI evaluation board Quick view
主な特徴
Voltage range from 10.5 V to 85 V Low Rds(ON) MOSFETs in DPAK package SPI with daisy chain feature FLAG and BUSY LED indicators Adjustable supply voltage compensation Flexible supply voltage management Suitable for use in combination with the STEVAL-PCC009V2 さらに表示
画像
EVAL6482H High power microstepping motor driver with the L6482H Quick view
主な特徴
Voltage range from 10.5 V to 85 V Low Rds(ON) MOSFETs in DPAK package SPI with daisy chain feature FLAG and BUSY LED indicators Flexible supply voltage management Suitable for use in combination with the STEVAL-PCC009V2 さらに表示
画像