Portable Media Players

Key Features

• Bluetooth^® SMART small form factor board based on the SPBTLE-1S module, Bluetooth v4.2 compliant
• On-board SPBTLE-1S module, based on BlueNRG-1, Bluetooth low energy application processor system on chip embedding:
  • an ultra-low power ARM^® Cortex^® -M0 32-bit core architecture
  • programmable embedded 160 KB Flash
  • 24 KB embedded RAM with data retention
• On-board MP34DT05-A (or MP34DT04-C1 in the first generation board) digital MEMS microphone
• On-board LSM6DSL: MEMS 3D accelerometer (±2 / ±4 / ±8 / ±16 g) plus 3D gyroscope (±125 / ±245 / ±500 / ±1000 / ±2000 dps)
• Voltage supply: 1V8 or 3V3
• Battery or USB powered
• 100 mAh Li-Ion battery
• On-board STBC08 linear Li-Ion battery charger
• SWD connector
• Included in the development kit package:
  • STEVAL-BLUEMIC-1
  • Plastic box for housing STEVAL-BLUEMIC-1
  • 100 mAh Li-Ion battery
  • SWD programming cable
• SW development kit for audio and inertial MEMS data streaming over BLE
• ST BlueMS: Android and iOS demo App available in the respective stores
• CE certified
• RoHS and China RoHS compliant
• Contains Transmitter Module FCC (ID: S9NSPBTLE1S) certified
• Contains Transmitter Module IC (IC: 8976C-SPBTLE1S) certified

Show More

Key Features

• Bluetooth^® SMART board with the SPBTLE-1S certified module based on the BlueNRG-1 Bluetooth low energy system-on-chip
• Associated BlueNRG-1 development kit SW package including firmware and documentation
• Up to +5 dBm available output power
• Bluetooth^® low energy v4.2 compliant, supports master, slave and simultaneous master-and-slave roles
• Integrated balun which integrates a matching network and harmonics filter
• SMA connector for antenna or measuring equipment
• 3 user LEDs
• 2 user buttons
• 3D digital accelerometer and 3D digital gyroscope
• MEMS pressure sensor with embedded temperature sensor
• Battery holder
• JTAG debug connector
• USB to serial bridge for providing I/O channel with the BlueNRG-1 device
• Jumper for measuring current for BlueNRG-1 only
• RoHS compliant

Show More

Key Features

• STWLC33 evaluation board with Würth Elektronik dual mode coil (760308102207)
• Qi 1.2 compliant, supporting extended power profile: up to 15 W/10 V maximum output power
• Backward compatible with Qi baseline power profile: up to 5 W/5 V maximum output power
• PMA-SR1 (AirFuel inductive) compliant: 5 W/5.6 V maximum output power
• Transmitter function based on Qi protocol to charge wearable devices using the same Rx coil (up to 3 W power)
• Total system efficiency up to 80%
• Configurable GPIOs for status indication
• I²C interface for communication with the host system
• Foreign object detection (FOD)
• Complete kit (IC, firmware)
• RoHS compliant

Show More

Key Features

• Bluetooth^® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
• Associated BlueNRG-2 development kit SW package including firmware and documentation
• Up to +8 dBm available output power (at antenna connector)
• Excellent receiver sensitivity (-88 dBm)
• Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
• Bluetooth^® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
• New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
• SMA connector for antenna or measuring equipment
• 3 user LEDs
• 2 user buttons
• 3D digital accelerometer and 3D digital gyroscope
• MEMS pressure sensor with embedded temperature sensor
• RoHS compliant

Show More

Key Features

• STWBC-EP digital controller
• 15 W output power
• Qi MP-A10 reference design
• WPC Qi1.2.3 standard compliant
• Robust demodulation algorithm, with triple path (V, I, f)
• Foreign object detection (FOD)
• Accurate power control
• Active presence detection
• UART protocol to control and monitor the system
• Complete reference design (evaluation board, IC, firmware and tools)
• 2-layer PCB for easy design
• Flash memory-based
• RoHS compliant

Show More

Key Features

• STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
• X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
• SPBTLE-RF:
  • Bluetooth Low Energy FCC and IC certified module based on Bluetooth^® SMART 4.1 network processor BlueNRG-MS
  • Integrated Balun (BALF-NRG-01D3)
  • Chip antenna
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• Scalable solution, capable of cascading multiple boards for larger systems
• Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
• RoHS compliant

Show More

Key Features

• Included in the development kit package:
  • SensorTile module (STEVAL-STLCS01V1) with STM32L476JG, LSM6DSM, LSM303AGR, LPS22HB, MP34DT05-A, BlueNRG-MS, BALF-NRG-02D3 and LD39115J18R
  • SensorTile expansion Cradle board equipped with audio DAC, USB port, STM32 Nucleo, Arduino UNO R3 and SWD connector
  • SensorTile Cradle with battery charger, humidity and temperature sensor, SD memory card slot, USB port and breakaway SWD connector
  • 100 mAh Li-Ion battery
  • Plastic box
  • SWD programming cable
• Software libraries and tools
  • STSW-STLKT01: SensorTile firmware package that supports sensors raw data streaming via USB, data logging on SDCard, audio acquisition and audio streaming.
  • FP-SNS-ALLMEMS1 and FP-SNS-MOTENV1: STM32Cube function packs
  • STBLESensor: iOS and Android demo Apps
  • BlueST-SDK: iOS and Android Software Development Kit
• CE certified
• RoHS and China RoHS compliant
• WEEE compliant
• FCC (ID: S9NSTILE01) certified
• IC (IC: 8976C-STILE01) certified with PMN: STEVAL-STLKT01V1; HVIN: STEVAL-STLCS01V1; HMN: STEVAL-STLCX01V1; FVIN: bluenrg_7_1_e_Mode_2-32MHz-XO32K_4M.img
• TYPE certified (006-000482)

Show More

Key Features

• Contains FCC ID: S9NBCOIN01
• Contains module IC 8976C-BCOIN01 certified with PMN: STEVAL-BCNKT01V1; HVIN: STEVAL-BCNCS01V1; HMN: STEVAL-BCNCR01V1; FVIN: bluenrg_7_2_c_Mode_2-32MHz-XO32K_4M.img
• The development kit package includes:
  • BlueCoin module (STEVAL-BCNCS01V1) with STM32F446, LSM6DSM, LSM303AGR, LPS22HB, 4x MP34DT06J, BlueNRG-MS, BALF-NRG-01D3, STBC03JR
  • CoinStation (STEVAL-BCNST01V1) board
  • BlueCoin Cradle (STEVAL-BCNCR01V1)
  • 130 mAh Li-Po battery
  • Plastic box for housing the BlueCoin cradle and the battery
  • SWD programming cable
• Software libraries and tools:
  • STSW-BCNKT01 firmware package with raw sensor data streaming support via USB, data logging on SDCard, audio acquisition and audio streaming, time-of-flight example and BLE protocol to interface to a Smartphone App
  • FP-AUD-SMARTMIC1: smart audio IN-OUT software expansion for STM32Cube
  • FP-SNS-ALLMEMS1: STM32 ODE function pack for BLE and sensors
  • FP-AUD-BVLINK1: BLE and microphones software expansion for STM32Cube
  • STBLESensor: iOS™ and Android™ demo apps
  • BlueST-SDK: iOS and Android software development kit
  • Compatible with STM32 ecosystem through STM32Cube support

Show More

Key Features

• Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
• Key features:
  • Low operating input voltage (from 1.4 V to 5.5 V)
  • Current capability from 200 mA to 300 mA
  • Low dropout (down to 160 mV typ.)
  • Ultra-low quiescent current (down to 500 nA typ.)
  • Low noise (down to 6.5 μVRMS typ.)
  • High PSSR (up to 80 dB)
  • Logic controlled electronic shutdown (enable)
  • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
• RoHS compliant

Show More