Overview
Solutions
HW Evaluation Tools
Resources
Tools and Software
Key Products
Get Started

With the aim of reducing CO2 emissions, turbocharger systems  are evolving from exhaust gas driven to electric driven forms for use in  Mild Hybrid Electric Vehicles (MHEV). The superchargers improve the response of the engines at low revolutions and also enhance performance. An electric supercharger  responds instantaneously, removes lag and improves the vehicle’s acceleration. ST is enabling the electric supercharger application with its extensive product portfolio including an integrated solution for electric motors using the 48 V 3-phase driver  L9907 and an 32-bit automotive MCU; the offer is completed by LDO voltage regulators, protections and very low on-state resistance  N-channel Power MOSFETs.

    • Combining the SPC56P-Discovery board and EVAL-L9907 (up to 20A) or EVAL-L9907H (up to 120A) evaluation board with related Graphical User Interface (GUI) STSW-L9907 or STSW-L9907-H, you can easily evaluate your brushless motor control applications.
      Solution Components
      Part Number Description Status Core Products Price (US$)*
      Order / Download
      L9907

      Key features

      • AEC-Q100 qualified
      • Supply voltage from 4.2V to 54 V for working in single (12 V systems), double (24 V systems) and 48 V battery applications
      • The device can withstand -7 V to 90 V at the FET high-side Driver pins
      • Low standby current consumption
      • 3.3 V internal regulator supplied by Vcc pin
      • Boost regulator for full Rdson down to 6 V and over voltage protection
      • 3 low-side + 3 high-side drivers
        • PWM operation up to 20 kHz
        • Gate driver current adjustable via SPI in 4 steps. Range set via external resistor. Maximum gate controlled current 600 mA
        • Source connection to each MOSFET
      • Input pin for each gate driver
      • 2-differential current sense amplifiers:
        • Output offset selectable via SPI (0.2*Vcc offset for ground shunt resistors connection, 0.5*Vcc offset for phase shunt resistors connection)
        • All the amplifier gain factors are programmable (10, 30, 50, 100)
      • 8 MHz, 16-bit SPI
        • Full diagnostic
        • Programmable parameters:
          • Cross conduction dead time with a fixed minimum value
          • 4 current steps driving the PowerMOS gates (25%, 50%, 75%, 100%)
          • Phase or ground selection of current sense amplifier
          • Gain values for the current sense amplifiers
          • Zero current output voltage (offset) for the current sense amplifiers
          • Over voltage threshold selection for single or double battery operation
          • Short circuit detection thresholds for the low-side and the high-side MOSFETs (drain to source voltage monitor).
      • Protection and diagnostic
        • FET driver:
          • FET driver supply Undervoltage (UV) diagnostic;
          • Gate to source output voltage limit;
          • Gate to source passive switch off.
        • Power supply pins VB and VCC :
          • Overvoltage (OV), Undervoltage (UV) diagnostic and protection
        • All logic pins withstand 35 V
        • Power MOSFET drain to source voltage drop measurement for overcurrent protection
        • Over-temperature diagnostic and shutdown
        • Fault status flag output

      Show more

      3 phase gate driver for 6step or FOC controlled Brushless Motors compatible with 48V NET
      Active
      8.98 Buy now
      EVAL-L9907-H

      Key features

      • Supply voltage range (VBatt): 6 V÷54 V
      • Load Current Capability up to 120 A
      • Device control and diagnostic via SPI
      • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
      • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
      • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
      • Total accessibility to all pins by test points
      • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
      • Possibility to connect external USB adapter for the SPI communication
      • Possibility to use external Boost components by removing jumpers

      Show more

      FEATURED RESOURCES

      schematics gerber
      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V - high Current version (120Amps)
      Active
      L9907 269.50 Buy now
      EVAL-L9907

      Key features

      • Supply voltage range (VBatt): 6 V÷54 V
      • Load Current Capability up to 20 A
      • Device control and diagnostic via SPI
      • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
      • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
      • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
      • Total accessibility to all pins by test points
      • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
      • Possibility to connect external USB adapter for the SPI communication
      • Possibility to use external Boost components by removing jumpers

      Show more

      IMAGE

      EVAL-L9907
      EVAL-L9907

      FEATURED RESOURCES

      schematics gerber
      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V
      Active
      L9907 245.00 Buy now
      SPC56P-Discovery

      Key features

      • SPC560P50L5 32-bit 64MHz e200z0h CPU;32-bit Power Architecture® Technology CPU, 576 KB Flash in an LQFP144 package.
      • Shield Connectors (Arduinocompatible).
      • On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers (2 x 7 male 100mil connector).
      • Free 128 Kbyte code size limited debugging
      • Board power supply: from the USB bus (5 V supply voltage) or through external +12 V PSU.
      • All GPIOs and DSPI/USB signals accessible by a 4x37 100mil pin grid array allowing connection of an additional boards for dedicated applications.
      • CAN, K-LINE, LIN, FlexRay interfaces.
      • Main power switch.
      • Reset push button.
      • 2 potentiometers for ADC evaluation
      • 12 MHz crystal.
      • Board size 152 x 103 mm

      Show more

      IMAGE

      SPC56P-Discovery
      SPC56P-Discovery

      FEATURED RESOURCES

      gerber
      Discovery Kit for SPC56 P line - with SPC560P50L5 MCU
      Active
      98.00 Buy now
      STSW-L9907-H

      Key features

      • Complete Graphical User Interface (GUI) for EVAL-L9907H evaluation board.

      Show more

      EVAL-L9907-H Graphical User Interface
      Active
      -
      Software
      Part Number Software Version Marketing Status Supplier Download
      STSW-L9907-H 3.0.0 Active ST
      STSW-L9907

      Key features

      • Complete Graphical User Interface (GUI) for EVAL-L9907 evaluation board.

      Show more

      EVAL-L9907 Graphical User Interface
      Active
      -
      Software
      Part Number Software Version Marketing Status Supplier Download
      STSW-L9907 3.0.0 Active ST
      L9907

      Description:

      3 phase gate driver for 6step or FOC controlled Brushless Motors compatible with 48V NET

      Price (US$)*

      8.98

      Key features

      • AEC-Q100 qualified
      • Supply voltage from 4.2V to 54 V for working in single (12 V systems), double (24 V systems) and 48 V battery applications
      • The device can withstand -7 V to 90 V at the FET high-side Driver pins
      • Low standby current consumption
      • 3.3 V internal regulator supplied by Vcc pin
      • Boost regulator for full Rdson down to 6 V and over voltage protection
      • 3 low-side + 3 high-side drivers
        • PWM operation up to 20 kHz
        • Gate driver current adjustable via SPI in 4 steps. Range set via external resistor. Maximum gate controlled current 600 mA
        • Source connection to each MOSFET
      • Input pin for each gate driver
      • 2-differential current sense amplifiers:
        • Output offset selectable via SPI (0.2*Vcc offset for ground shunt resistors connection, 0.5*Vcc offset for phase shunt resistors connection)
        • All the amplifier gain factors are programmable (10, 30, 50, 100)
      • 8 MHz, 16-bit SPI
        • Full diagnostic
        • Programmable parameters:
          • Cross conduction dead time with a fixed minimum value
          • 4 current steps driving the PowerMOS gates (25%, 50%, 75%, 100%)
          • Phase or ground selection of current sense amplifier
          • Gain values for the current sense amplifiers
          • Zero current output voltage (offset) for the current sense amplifiers
          • Over voltage threshold selection for single or double battery operation
          • Short circuit detection thresholds for the low-side and the high-side MOSFETs (drain to source voltage monitor).
      • Protection and diagnostic
        • FET driver:
          • FET driver supply Undervoltage (UV) diagnostic;
          • Gate to source output voltage limit;
          • Gate to source passive switch off.
        • Power supply pins VB and VCC :
          • Overvoltage (OV), Undervoltage (UV) diagnostic and protection
        • All logic pins withstand 35 V
        • Power MOSFET drain to source voltage drop measurement for overcurrent protection
        • Over-temperature diagnostic and shutdown
        • Fault status flag output

      Show more

      EVAL-L9907-H

      Description:

      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V - high Current version (120Amps)

      Price (US$)*

      269.50

      Key features

      • Supply voltage range (VBatt): 6 V÷54 V
      • Load Current Capability up to 120 A
      • Device control and diagnostic via SPI
      • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
      • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
      • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
      • Total accessibility to all pins by test points
      • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
      • Possibility to connect external USB adapter for the SPI communication
      • Possibility to use external Boost components by removing jumpers

      Show more

      FEATURED RESOURCES

      schematics gerber
      EVAL-L9907

      Description:

      Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V

      Price (US$)*

      245.00

      Key features

      • Supply voltage range (VBatt): 6 V÷54 V
      • Load Current Capability up to 20 A
      • Device control and diagnostic via SPI
      • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
      • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
      • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
      • Total accessibility to all pins by test points
      • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
      • Possibility to connect external USB adapter for the SPI communication
      • Possibility to use external Boost components by removing jumpers

      Show more

      IMAGE

      EVAL-L9907
      EVAL-L9907

      FEATURED RESOURCES

      schematics gerber
      SPC56P-Discovery

      Description:

      Discovery Kit for SPC56 P line - with SPC560P50L5 MCU

      Price (US$)*

      98.00

      Key features

      • SPC560P50L5 32-bit 64MHz e200z0h CPU;32-bit Power Architecture® Technology CPU, 576 KB Flash in an LQFP144 package.
      • Shield Connectors (Arduinocompatible).
      • On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers (2 x 7 male 100mil connector).
      • Free 128 Kbyte code size limited debugging
      • Board power supply: from the USB bus (5 V supply voltage) or through external +12 V PSU.
      • All GPIOs and DSPI/USB signals accessible by a 4x37 100mil pin grid array allowing connection of an additional boards for dedicated applications.
      • CAN, K-LINE, LIN, FlexRay interfaces.
      • Main power switch.
      • Reset push button.
      • 2 potentiometers for ADC evaluation
      • 12 MHz crystal.
      • Board size 152 x 103 mm

      Show more

      IMAGE

      SPC56P-Discovery
      SPC56P-Discovery

      FEATURED RESOURCES

      gerber
      STSW-L9907-H

      Description:

      EVAL-L9907-H Graphical User Interface

      Price (US$)*

      -
      Software

      Key features

      • Complete Graphical User Interface (GUI) for EVAL-L9907H evaluation board.

      Show more

      Part Number Software Version Marketing Status Supplier Download
      STSW-L9907-H 3.0.0 Active ST
      STSW-L9907

      Description:

      EVAL-L9907 Graphical User Interface

      Price (US$)*

      -
      Software

      Key features

      • Complete Graphical User Interface (GUI) for EVAL-L9907 evaluation board.

      Show more

      Part Number Software Version Marketing Status Supplier Download
      STSW-L9907 3.0.0 Active ST

Part Number
Description
EVAL-L9907 Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V Quick view

Key Features

  • Supply voltage range (VBatt): 6 V÷54 V
  • Load Current Capability up to 20 A
  • Device control and diagnostic via SPI
  • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
  • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
  • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
  • Total accessibility to all pins by test points
  • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
  • Possibility to connect external USB adapter for the SPI communication
  • Possibility to use external Boost components by removing jumpers

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics Gerber
SPC56P-Discovery Discovery Kit for SPC56 P line - with SPC560P50L5 MCU Quick view

Key Features

  • SPC560P50L5 32-bit 64MHz e200z0h CPU;32-bit Power Architecture® Technology CPU, 576 KB Flash in an LQFP144 package.
  • Shield Connectors (Arduinocompatible).
  • On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers (2 x 7 male 100mil connector).
  • Free 128 Kbyte code size limited debugging
  • Board power supply: from the USB bus (5 V supply voltage) or through external +12 V PSU.
  • All GPIOs and DSPI/USB signals accessible by a 4x37 100mil pin grid array allowing connection of an additional boards for dedicated applications.
  • CAN, K-LINE, LIN, FlexRay interfaces.
  • Main power switch.
  • Reset push button.
  • 2 potentiometers for ADC evaluation
  • 12 MHz crystal.
  • Board size 152 x 103 mm

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Gerber
SPC5-UDEDEBG PLS JTAG debugger software full license or license renewal Quick view

Key Features

  • Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board.
  • Supports SPC5x MCUs
  • Supports Multicore, eTPU and GTM debugging
  • Includes FLASH programming capability
  • Support service provided through STMicroelectronics

Show More

EVAL-L9907-H Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V - high Current version (120Amps) Quick view

Key Features

  • Supply voltage range (VBatt): 6 V÷54 V
  • Load Current Capability up to 120 A
  • Device control and diagnostic via SPI
  • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
  • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
  • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
  • Total accessibility to all pins by test points
  • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
  • Possibility to connect external USB adapter for the SPI communication
  • Possibility to use external Boost components by removing jumpers

Show More

FEATURED RESOURCES

Schematics Gerber
Part Number
EVAL-L9907

Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V

Key Features

  • Supply voltage range (VBatt): 6 V÷54 V
  • Load Current Capability up to 20 A
  • Device control and diagnostic via SPI
  • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
  • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
  • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
  • Total accessibility to all pins by test points
  • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
  • Possibility to connect external USB adapter for the SPI communication
  • Possibility to use external Boost components by removing jumpers

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics Gerber
SPC56P-Discovery

Discovery Kit for SPC56 P line - with SPC560P50L5 MCU

Key Features

  • SPC560P50L5 32-bit 64MHz e200z0h CPU;32-bit Power Architecture® Technology CPU, 576 KB Flash in an LQFP144 package.
  • Shield Connectors (Arduinocompatible).
  • On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers (2 x 7 male 100mil connector).
  • Free 128 Kbyte code size limited debugging
  • Board power supply: from the USB bus (5 V supply voltage) or through external +12 V PSU.
  • All GPIOs and DSPI/USB signals accessible by a 4x37 100mil pin grid array allowing connection of an additional boards for dedicated applications.
  • CAN, K-LINE, LIN, FlexRay interfaces.
  • Main power switch.
  • Reset push button.
  • 2 potentiometers for ADC evaluation
  • 12 MHz crystal.
  • Board size 152 x 103 mm

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Gerber
SPC5-UDEDEBG

PLS JTAG debugger software full license or license renewal

Key Features

  • Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board.
  • Supports SPC5x MCUs
  • Supports Multicore, eTPU and GTM debugging
  • Includes FLASH programming capability
  • Support service provided through STMicroelectronics

Show More

EVAL-L9907-H

Evaluation board for L9907 highly integrated 3-phase BLDC motors pre-driver with integrated rail-to-rail operational ampliers and Inductive booster for system operation from 6V up to 54V - high Current version (120Amps)

Key Features

  • Supply voltage range (VBatt): 6 V÷54 V
  • Load Current Capability up to 120 A
  • Device control and diagnostic via SPI
  • Flexible shunt configuration (Phase U+PhaseV or PhaseU+Total Phase)
  • 4 LEDs for monitoring VBatt, Vcc, EN1 and EN2 signal
  • Input signal connector compatible with SPC56 Discovery boards. A different microcontroller board can be connected by a simple adaptor or wire
  • Total accessibility to all pins by test points
  • Modular PCBs design to easily change the external Power MOS both SMD and throughhole Power MOS
  • Possibility to connect external USB adapter for the SPI communication
  • Possibility to use external Boost components by removing jumpers

Show More

FEATURED RESOURCES

Schematics Gerber
00 Files selected for download

Technical Documentation

    • Description Version Size Action
      AN4789
      Monolithic Schottky diode in ST F7 LV MOSFET technology: improving application performance
      1.1
      1,006.7 KB
      PDF
      AN2689
      Protection of automotive electronics from electrical hazards, guidelines for design and component selection
      3.1
      797.51 KB
      PDF
      AN5124
      Supply voltage configuration of 3-phase BLDC automotive MOSFET driver L9907
      1.0
      2.64 MB
      PDF
      AN4789

      Monolithic Schottky diode in ST F7 LV MOSFET technology: improving application performance

      AN2689

      Protection of automotive electronics from electrical hazards, guidelines for design and component selection

      AN5124

      Supply voltage configuration of 3-phase BLDC automotive MOSFET driver L9907

Publications and Collaterals

    • Description Version Size Action
      ST Protection Finder - The new app for Android and iOS 1.0
      1.52 MB
      PDF
      eDesignSuite-The smart way to design your application 1.0
      842.88 KB
      PDF

      ST Protection Finder - The new app for Android and iOS

      eDesignSuite-The smart way to design your application

Design Tools

    • Part Number

      Transient voltage suppressor smart selection tool

      Smart Selector for Micro 32bit Power Architecture products

Development Tools

    • Part Number

      Code Generator, Quick resources configurator and Eclipse development environment for SPC5 MCUs

      SPC5-UDESTK Debugging Software for Windows

      Protection product finder application for Android and iOS

      Diode product finder application for Android and iOS

Embedded Software

    • Part Number

      EVAL-L9907 Graphical User Interface

      EVAL-L9907-H Graphical User Interface

      SPC5-EV-ADIS Graphical User Interface for M0-7 High Side Drivers

Automotive Analog and Power

Part number Description
L5300AH7 5V Low drop voltage regulator
L5300EPT 5 V low dropout voltage regulator
L5300GJ Standard Functions, Voltage Regulators
L5300RPT 5 V low dropout voltage regulator
L9777 Low power voltage regulator
L9907 3 phase gate driver for 6step or FOC controlled Brushless Motors compatible with 48V NET
Part number
5V Low drop voltage regulator
5 V low dropout voltage regulator
Standard Functions, Voltage Regulators
5 V low dropout voltage regulator
Low power voltage regulator
3 phase gate driver for 6step or FOC controlled Brushless Motors compatible with 48V NET

Automotive Microcontrollers

Part number Description
SPC560P50L5 32-bit Power Architecture MCU for Automotive Chassis and Safety Applications
Part number
32-bit Power Architecture MCU for Automotive Chassis and Safety Applications

Power Transistors

Part number Description
STD105N10F7AG Automotive-grade N-channel 100 V, 6.8 mOhm typ., 80 A STripFET F7 Power MOSFET in a DPAK package
STH275N8F7-6AG Automotive-grade N-channel 80 V, 1.7 mOhm typ., 180 A STripFET F7 Power MOSFET in H2PAK-6 package
STH315N10F7-6 Automotive-grade N-channel 100 V, 2.1 mOhm typ., 180 A STripFET F7 Power MOSFET in H2PAK-6 package
STL135N8F7AG Automotive-grade N-channel 80 V, 3.15 mOhm typ., 130 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
Part number
Automotive-grade N-channel 100 V, 6.8 mOhm typ., 80 A STripFET F7 Power MOSFET in a DPAK package
Automotive-grade N-channel 80 V, 1.7 mOhm typ., 180 A STripFET F7 Power MOSFET in H2PAK-6 package
Automotive-grade N-channel 100 V, 2.1 mOhm typ., 180 A STripFET F7 Power MOSFET in H2PAK-6 package
Automotive-grade N-channel 80 V, 3.15 mOhm typ., 130 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package

Protection Devices

Part number Description
SM30TY Automotive 3000 W TVS in SMC
SM6TY Automotive 600 W TVS in SMB
Part number
Automotive 3000 W TVS in SMC
Automotive 600 W TVS in SMB