Room Air Condition (RAC)

Key Features

• On-board NFC card reader IC: ST25R3911B
• 47 mm x 34 mm, four turns, 13.56 MHz inductive antenna etched on PCB and associated tuning circuit
• Six general purpose LEDs
• ISO 18092 (NFCIP-1) active P2P
• ISO 14443A and ISO14443B
• ISO 15693
• FeliCa™
• VHBR
  • 6.8 Mbit/s AFE and PCD to PICC framing
  • 3.4 Mbit/s PICC to PCD framing
• Up to 1.4 W output power with differential antenna
• Possibility of driving two antennas in single ended configuration
• Inductive and capacitive wake-up
• Automatic antenna tuning system
• Transparent and Stream modes to implement MIFARE™ Classic compliant or other custom protocols
• Equipped with Arduino™ UNO R3 connector
• Free comprehensive development firmware library compatible with STM32Cube and samples for ST25R3911B
• Scalable solution for multiple board cascade
• FCC certified
• RoHS compliant

Show More

Key Features

• Very compact module for motion, audio, environmental sensing and Bluetooth^® low energy connectivity with a complete set of firmware examples
• Mobile connectivity via the STBLESensor app, available for iOS™ and Android™
• Main components:
  • STM32L476JG – 32-bit ultra-low-power MCU with Cortex^® M4F
  • LSM6DSM – iNEMO inertial module: 3D accelerometer and 3D gyroscope
  • LSM303AGR – Ultra-compact high-performance eCompass module: ultra-low power 3D accelerometer and 3D magnetometer
  • LPS22HB – MEMS nano pressure sensor: 260-1260 hPa absolute digital output barometer
  • MP34DT05-A – 64 dB SNR digital MEMS microphone
  • BlueNRG-MS – Bluetooth low energy network processor
  • BALF-NRG-02D3 – 50 Ω balun with integrated harmonic filter
  • LD39115J18R – 150 mA low quiescent current low noise LDO 1.8 V
• 2 V - 5.5 V power supply range
• External interfaces: UART, SPI, SAI (Serial Audio Interface), I²C, DFSDM, USB OTG, ADC, GPIOs
• Solderable only interface (no connector on back side)
• SWD interface for debugging and programming capability
• CE certified
• RoHS and China RoHS compliant
• WEEE compliant
• FCC certified
• IC certified
• TYPE certified

Show More

Key Features

• STM32 Nucleo expansion board based on the ST7580 power line networking system-on-chip
• ST7580 main characteristics:
  • FSK, PSK modem for robust wireline communication up to 28.8 kbps
  • 8-18 V analog supply voltage
  • 3.3 V digital supply
  • Output transmitted signal capability up to 14 V_p-p , 1 A_rms
  • Frequency range 9-250 kHz
• TX and RX filters on board optimized for the CENELEC B (95-125 kHz) frequency band, suitable for IoT / Smart Home / Smart City applications
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connectors
• Example firmware available for point-to-point communication, compatible with STM32Cube firmware
• RoHS compliant

Show More

Key Features

• Contains FCC ID: S9NBCOIN01
• Contains module IC 8976C-BCOIN01 certified with PMN: STEVAL-BCNKT01V1; HVIN: STEVAL-BCNCS01V1; HMN: STEVAL-BCNCR01V1; FVIN: bluenrg_7_2_c_Mode_2-32MHz-XO32K_4M.img
• The development kit package includes:
  • BlueCoin module (STEVAL-BCNCS01V1) with STM32F446, LSM6DSM, LSM303AGR, LPS22HB, 4x MP34DT06J, BlueNRG-MS, BALF-NRG-01D3, STBC03JR
  • CoinStation (STEVAL-BCNST01V1) board
  • BlueCoin Cradle (STEVAL-BCNCR01V1)
  • 130 mAh Li-Po battery
  • Plastic box for housing the BlueCoin cradle and the battery
  • SWD programming cable
• Software libraries and tools:
  • STSW-BCNKT01 firmware package with raw sensor data streaming support via USB, data logging on SDCard, audio acquisition and audio streaming, time-of-flight example and BLE protocol to interface to a Smartphone App
  • FP-AUD-SMARTMIC1: smart audio IN-OUT software expansion for STM32Cube
  • FP-SNS-ALLMEMS1: STM32 ODE function pack for BLE and sensors
  • FP-AUD-BVLINK1: BLE and microphones software expansion for STM32Cube
  • STBLESensor: iOS™ and Android™ demo apps
  • BlueST-SDK: iOS and Android software development kit
  • Compatible with STM32 ecosystem through STM32Cube support

Show More

Key Features

• Input voltage from 7 V to 45 V
• Output current up to 15 A_rms
• Power stage based on STD140N6F7 MOSFETs
• Embedded 3.3 V buck regulator
• Embedded 12 V LDO regulator
• Single shunt current sensing
• Digital Hall sensors and encoder input
• Overcurrent comparator
• Bus voltage sensing
• Fully compatible with STM32 PMSM FOC software development kit
• 6-step sensorless and sensored firmware supported
• Embedded ST-LINK/V2-1
• Easy user interface with buttons and trimmer
• STM32 FW boot loader supported
• RoHS compliant

Show More

Key Features

• Input voltage: from 125 to 400 V_DC
• Nominal power: up to 600 W
• Nominal current: up to 4.8 A_rms
• Input auxiliary voltage: up to 20 V_DC
• Single- or three-shunt resistors for current sensing (with sensing network)
• Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• IGBT intelligent power module:
  • 2^nd series SLLIMM-nano IPM (STGIPQ8C60T-HZ – full molded package)
• Motor control connector (32 pins) interfacing with ST MCU boards
• Universal design for further evaluation with bread board and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Input voltage: from 125 to 400 V_DC
• Nominal power: up to 60 W
• Nominal current: up to 0.35 Arms
• Input auxiliary voltage: up to 20 V_DC
• Single- or three-shunt resistors for current sensing (with sensing network)
• Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Intelligent power module:
  • SLLIMM-nano IPM MOSFET-based (STIPN1M50T-H – full molded package)
• Motor control connector (32 pins) interfacing with ST MCU boards
• Universal design for further evaluation with bread board and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Input voltage: from 125 to 400 V_DC
• Nominal power: up to 100 W
• Nominal current: up to 0.6 A_rms
• Input auxiliary voltage: up to 20 V_DC
• Single- or three-shunt resistors for current sensing (with sensing network)
• Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Intelligent power module:
  • SLLIMM-nano IPM MOSFET-based (STIPN2M50T-H – full molded package)
• Motor control connector (32 pins) interfacing with ST MCU boards
• Universal design for further evaluation with bread board and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Input voltage: from 125 to 400 V_DC
• Nominal power: up to 450 W
• Nominal current: up to 3 A_rms
• Input auxiliary voltage: up to 20 V_DC
• Single- or three-shunt resistors for current sensing (with sensing network)
• Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• IGBT intelligent power module:
  • 2^nd series SLLIMM-nano IPM (STGIPQ5C60T-HZ – full molded package)
• Motor control connector (32 pins) interfacing with ST MCU boards
• Universal design for further evaluation with bread board and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Nominal power: up to 100 W
• Compatible with 3.3 V and 5 V control board
• Single shunt resistor for current reading
• On-board temperature sensor
• Overcurrent protection with boost/disabling capability
• For six-step drives:
  • Current limitation/regulation network
  • BEMF detection network
• MC connector
• Compatible with sinusoidal and trapezoidal control
• RoHS compliant

Show More

Key Features

• Wide-range input voltage (30-270 Vac)
• Maximum power up to 100 W at 230 Vac input
• Based on the STGIPN3H60A SLLIMM™-nano AC motor drive
• Mounts the VIPer06 fixed frequency offline converter from the VIPer™ plus family
• Efficient DC-DC power supply (15 V, 3.3 V)
• DC bus voltage power supply connectors
• External 15 V input
• Dedicated connector for interfacing with the various other ST evaluation boards
• Suitable for sinusoidal FOC drives
• Selectable single or three-shunt current reading topology with fast operational amplifier
• Configurable for direct motor current sampling from shunt resistors
• Hardware overcurrent detecting network
• Temperature sensor
• Hall sensor/quadrature encoder inputs
• RoHS compliant

Show More

Key Features

• Nominal power 1300 W, max. power 1700 W
• Digital PFC section:
  • Single-stage boost converter based on the STGW35HF60W (or STW38N65M5) and STTH15R06D or (STPSC1206D)
  • AC mains current sensing
  • DC bus voltage sensing
  • Hardware overcurrent protection
  • Hardware overvoltage protection
  • AC mains voltage zero crossing detection
  • Rectified AC mains voltage sensing
  • External boost inductor
• Inverter section (motor 1 drive):
  • IGBT intelligent power module STGIPS20C60 in SDIP 25L molded package
  • 3-shunt or DC link motor current sensing
  • Hardware overcurrent protection
  • Heatsink temperature measurement
  • Overcurrent protection disabling network
• Control section:
  • Centralized dual motor control and PFC drive, using the STM32F103RCT6
  • MC connector to drive the second motor power stage (a compatible power board, such as the STEVAL-IHM021V1, STEVAL-IHM024V1, or STEVAL-IHM032V1, can be plugged here)
  • SWD programming and debugging
  • JTAG programming
  • Opto-isolated USART communication
• Other functions:
  • User key, reset, potentiometer, user LED, NTC relay, test points
• Power supply:
  • +15 V, +3.3 V power supply
• RoHS compliant

Show More

Key Features

• 3.3 V output voltage
• 3 A DC output current
• 4.5 V to 60 V input voltage
• 500 kHz switching frequency
• 3.5 ms programmed soft-start
• VBIAS switch-over for improved efficiency at light load
• 180° out of phase synchronization available
• Open drain PGOOD available
• Auto recovery overcurrent and thermal protection
• RoHS compliant

Show More

Key Features

• Ready-to-use printed circuit board (PCB) including:
  • M24SR64-Y Dynamic NFC/RFID tag
  • 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
  • STM32F103RGT6 64LQFP 32-bit microcontroller, with 1Mbytes of Flash memory
  • LCD Color Screen (320*200 pixels)
  • Different color LEDs
  • USB microB connector for board powering
  • JTAG connector for microcontroller firmware upgrade and debug
  • Joystick for menu selection
• M24SR-DISCO-PREM specific features:
  • Bluetooth module with audio outputs connected to Jack 3.5
  • Headset

Show More

Key Features

• Minimum input voltage: 125 VDC or 90 VAC
• Maximum input voltage: 400 VDC or 285 VAC
• Input voltage range with applied input voltage doubler from 65 VAC to 145 VAC
• Voltage range for low-voltage motor control applications from 18 VDC to 35 VDC
• Possibility to use auxiliary +15 V supply voltage
• Maximum output power for motors: up to 1 kW
• Regenerative brake control
• Input inrush limitation with bypass relay
• + 15 V auxiliary power supply based on buck converter with VIPer16
• IGBT power switch STGP10H60DF in a TO- 220 package - compatible with other ST IGBTs or power MOSFETs in the TO-220 package
• Fully populated board design with test points and isolated plastic cover for safety
• Motor control connector for interface with the STM3210B-EVAL board and other ST motor control dedicated kits
• Tachometer input
• Hall/encoder inputs
• Possibility to connect BEMF daughterboard for sensorless six-step control of BLDC motors
• PCB type and size:
  • PCB material: FR-4
  • Double-sided layout
  • Copper thickness: 60 μm
  • Total dimensions of board: 127 mm x 180 mm
• RoHS compliant

Show More

Key Features

• M24SR64-Y Dynamic NFC/RFID tag IC
• NFC antenna: 31 mm x 30 mm 13.56 MHz double layer inductive antenna etched on the PCB (ANT14)
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• Powered through the Arduino UNO R3 connectors
• 3 color LEDs for general purpose

Show More

Key Features

• LSM6DS0: MEMS 3D accelerometer (±2/±4/±8 g) + 3D gyroscope (±245/±500/±2000 dps)
• LIS3MDL: MEMS 3D magnetometer (±4/ ±8/ ±12/ 16 gauss)
• LPS25HB*: MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
• HTS221: capacitive digital relative humidity and temperature
• DIL 24-pin socket available for additional MEMS adapters and other sensors (UV index)
• Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• RoHS compliant

Show More

Key Features

• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• 30 µA I_Q at light load (LCM V_OUT = 3.3 V)
• 5 µA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• Contains the following ST sensors:
  • Pressure sensor LPS25HB
  • Humidity sensor HTS221
  • Accelerometer LIS3DH
  • Microphone MP34DT01
• AFE for processing the MP34DT01 microphone signal based on TSV522 low power, low offset op-amp
• Android app available
• RoHS compliant

Show More

Key Features

• 3-phase driver board for BLDC/PMSM motors
• Nominal operating voltage range from 10 V to 48 V DC
• 15 A_RMS output current
• Operating frequency selectable by firmware
• Overcurrent detection and protection (30 A_peak )
• Thermal monitoring and overheating protection
• Compatible with STM32 Nucleo boards
• Equipped with ST morpho connectors
• 3-Shunt and 1-Shunt configurable jumpers for motor current sensing
• Hall/Encoder motor sensor connector and circuit
• Debug connector for DAC, GPIOs, etc.
• Potentiometer available for speed regulation
• User LED
• RoHS compliant

Show More

Key Features

• Input voltage: 125 - 400 V_DC
• Nominal power: up to 500 W
• Nominal current: up to 3.0 A
• Input auxiliary voltage: up to 20 V DC
• Single or three-shunt resistors for current sensing (with sensing network)
• Two options for current sensing: dedicated op-amps or through MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Uses the STGIF5CH60TS-L IGBT intelligent power module from the 2^nd series of SLLIMM™ IPMs
• 32-pin motor control connector for interfacing with ST MCU boards
• Universal conception for further evaluation with breadboard and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Input voltage: 125 - 400 V_DC
• Nominal power: up to 1000 W
• Nominal power: up to 6 A
• Input auxiliary voltage: up to 20 V DC
• Single- or three- shunt resistors for current sensing (with sensing network)
• Two options for current sensing: dedicated op-amps or through MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Uses the STGIF10CH60TS-L IGBT intelligent power module from the 2^nd series of SLLIMM™ IPMs
• Motor control connector (32-pin) to interface with ST MCU boards
• Universal conception for further evaluation with breadboard and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Input voltage: 125 - 400 V_DC
• Nominal power: up to 1200 W
• Nominal current: up to 7 A
• Input auxiliary voltage: up to 20 V DC
• Single- or three- shunt resistors for current sensing (with sensing network)
• Two options for current sensing: dedicated op-amps or through MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Uses the STGIB10CH60TS-L IGBT intelligent power module from the 2^nd series of SLLIMM™ IPMs
• Motor control connector (32-pin) to interface with ST MCU boards
• Universal conception for further evaluation with breadboard and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Input voltage: 125 - 400 V_DC
• Nominal power: up to 1500 W
• Nominal current: up to 9 A
• Input auxiliary voltage: up to 20 V DC
• Single- or three-shunt resistors for current sensing (with sensing network)
• Two options for current sensing: dedicated op-amps or through MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Uses the STGIB15CH60TS-L IGBT intelligent power module from the 2^nd series of SLLIMM™ IPMs
• Motor control connector (32-pin) to interface with ST MCU boards
• Universal conception for further evaluation with breadboard and testing pins
• Very compact size

Show More

Key Features

• Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
• Up to 4-Kbit memory with NDEF support
• 54 mm diameter, single layer circular antenna
• Compatible with STM32 Nucleo boards
• Equipped with Arduino™ UNO R3 connector
• Self-powered or powered through the Arduino™ UNO R3 connectors
• Three general purpose LEDs
• Scalable solution, capable of cascading multiple boards for larger systems
• Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
• FCC and IC verified
• RoHS compliant

Show More

Key Features

• Input voltage: 125 - 400 V_DC
• Nominal power: up to 700 W
• Nominal current: up to 4.2 A
• Input auxiliary voltage: up to 20 V DC
• Single or three-shunt resistors for current sensing (with sensing network)
• Two options for current sensing: dedicated op-amps or through MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• Uses the STGIF7CH60TS-L IGBT intelligent power module from the SLLIMM™ 2^nd series IPMs
• Motor control connector (32-pin) interfacing with ST MCU boards
• Universal conception for further evaluation with bread board and testing pins
• Very compact size

Show More

Key Features

• Input voltage: from 125 to 400 V_DC
• Nominal power: up to 300 W
• Nominal current: up to 1.8 A
• Input auxiliary voltage: up to 20 V_DC
• Single- or three-shunt resistors for current sensing (with sensing network)
• Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• IGBT intelligent power module:
  • 2^nd series SLLIMM-nano IPM (STGIPQ3H60T-H – full molded package)
• Motor control connector (32 pins) interfacing with ST MCU boards
• Universal design for further evaluation with bread board and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F401VE high-performance ARM Cortex™ - M4 microcontroller
• Software-adjustable power circuitry to set sensor supply voltage from 0 to 3.6 V
• Includes a DIL24 socket for easy MEMS adapter connection
• Adjustable MEMS DIL24 power supply
• DFU-compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Embedded power monitoring circuitry on sensor supply voltage and current
• Debugging connector for SWD/JTAG
• Can be used with PC software like Unico GUI to manage and analyze MEMS sensor data
• RoHS compliant

Show More

Key Features

• Included in the development kit package:
  • SensorTile module (STEVAL-STLCS01V1) with STM32L476JG, LSM6DSM, LSM303AGR, LPS22HB, MP34DT05-A, BlueNRG-MS, BALF-NRG-02D3 and LD39115J18R
  • SensorTile expansion Cradle board equipped with audio DAC, USB port, STM32 Nucleo, Arduino UNO R3 and SWD connector
  • SensorTile Cradle with battery charger, humidity and temperature sensor, SD memory card slot, USB port and breakaway SWD connector
  • 100 mAh Li-Ion battery
  • Plastic box
  • SWD programming cable
• Software libraries and tools
  • STSW-STLKT01: SensorTile firmware package that supports sensors raw data streaming via USB, data logging on SDCard, audio acquisition and audio streaming.
  • FP-SNS-ALLMEMS1 and FP-SNS-MOTENV1: STM32Cube function packs
  • STBLESensor: iOS and Android demo Apps
  • BlueST-SDK: iOS and Android Software Development Kit
• CE certified
• RoHS and China RoHS compliant
• WEEE compliant
• FCC (ID: S9NSTILE01) certified
• IC (IC: 8976C-STILE01) certified with PMN: STEVAL-STLKT01V1; HVIN: STEVAL-STLCS01V1; HMN: STEVAL-STLCX01V1; FVIN: bluenrg_7_1_e_Mode_2-32MHz-XO32K_4M.img
• TYPE certified (006-000482)

Show More

Key Features

• Very compact module for motion, audio, environmental sensing and Bluetooth^® low energy connectivity with a complete set of firmware examples
• Mobile connectivity via the STBLESensor app, available for iOS™ and Android™
• Main components:
  • STM32L476JG – 32-bit ultra-low-power MCU with Cortex^® M4F
  • LSM6DSM – iNEMO inertial module: 3D accelerometer and 3D gyroscope
  • LSM303AGR – Ultra-compact high-performance eCompass module: ultra-low power 3D accelerometer and 3D magnetometer
  • LPS22HB – MEMS nano pressure sensor: 260-1260 hPa absolute digital output barometer
  • MP34DT05-A – 64 dB SNR digital MEMS microphone
  • BlueNRG-MS – Bluetooth low energy network processor
  • BALF-NRG-02D3 – 50 Ω balun with integrated harmonics filter
  • LD39115J18R – 150 mA low quiescent current low noise LDO 1.8 V
• 2 V - 5.5 V power supply range
• External interfaces: UART, SPI, SAI (serial audio interface), I²C, DFSDM, USB OTG, ADC, GPIOs
• Pluggable or solderable interface
• SWD interface for debugging and programming capability
• CE certified
• RoHS and China RoHS compliant
• WEEE compliant
• FCC certified
• IC certified
• TYPE certified

Show More

Key Features

• Input voltage: 125 to 400 V_DC
• Nominal power: up to 800 W
• Nominal current: up to 4.8 A
• Input auxiliary voltage: up to 20 V_DC
• Single- or three- shunt resistors for current sensing (with sensing network)
• Two options for current sensing: dedicated op-amps or through MCU
• Overcurrent hardware protection
• IPM temperature monitoring and protection
• Hall sensor or encoder input
• IGBT intelligent power module:
  • 2nd series of SLLIMM IPM (STGIB8CH60TS-L – DBC package)
• Motor control connector (32 pin) interfacing with ST MCU boards
• Universal design for further evaluation with bread board and testing pins
• Very compact size
• RoHS compliant

Show More

Key Features

• LSM6DSL MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±245/±500/±1000/±2000 dps)
• LSM303AGR MEMS 3D accelerometer (±2/±4/±8/±16 g) and MEMS3D magnetometer (±50 gauss)
• LPS22HB MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
• HTS221: capacitive digital relative humidity and temperature
• DIL24 socket for additional MEMS adapters and other sensors
• Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
• I²C sensor hub features on LSM6DSL available
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• RoHS compliant

Show More

Key Features

• ST25TA02K with a wet inlay 10*17 mm2 copper antenna
• ST25TA02K with a wet inlay aluminum antenna
• ST25TA02K with round- and square-stickers aluminum antennas
• ST25TA64K with a PET card
• ST25TA64K with a water-proof tag

Show More

Key Features

• ST25TA02K NFC seal
• ST25TA02K NFC stickers
• ST25TA02K key fob
• ST25TA02K NFC bracelet
• ST25TA64K NFC cards
• ST25TA02K NFC Secure paper label

Show More

Key Features

• Ready-to-use printed circuit board with
  • ST25TA02KB-P NFC/RFID Tag in UFDFPN5 ECOPACK®2 package
  • 19 mm2 single layer inductive antenna, etched on the PCB
• Contactless interface
  • TruST25™ digital signature
  • NFC Forum Type 4 Tag
  • ISO/IEC 14443 Type A
  • 106 kbps data rate
  • Internal 50 pF tuning capacitance, enabling design of small inductive antennas
• Memory
  • 256 Byte (2 Kbit) EEPROM with NDEF data support
  • 200-year data retention
  • 1 million erase-write cycles endurance
  • 128-bit password data protection
  • 20-bit event counter for read or write access with anti-tearing feature
• Digital pad
  • Configurable general purpose output (GPO) indicating, for example, RF field detection

Show More

Key Features

• Features
  • Input voltage: 230 V_AC 50 Hz / 60 Hz
  • Max. power: up to 2 kW
  • PFC topology: digital control, boost single stage
  • PFC protections: overcurrent, overvoltage, and undervoltage lockout
  • Inrush current limiter based on overvoltage protected AC switch
  • Motor 1 stage:
    • STGIB10CH60TS-L, SLLIMM series IPM 15 A, 600 V, 3-phase IGBT inverter bridge
    • Max. current: up to 10 A, 0-to-peak (current sensing network threshold)
    • 1-, 2-, and 3-shunt resistors for current sensing
    • Protections: overcurrent, overtemperature, undervoltage lockout
  • Motor 2 stage:
    • STGIPQ3H60T-HZ SLLIMM nano series IPM, 3 A, 600 V, 3-phase IGBT inverter bridge
    • Max. power: 60 W (no heatsink)
    • Max. current: up to 1 A, 0-to-peak (current sensor network threshold)
    • 1 shunt resistor for current sensing
    • Protections: overcurrent, overtemperature, undervoltage lockout
  • Centralized driving (motor 1, motor 2, PFC) from single STM32F303RB MCU based on ARM Cortex-M4 core with DSP and FPU
  • WEEE and RoHS compliant

Show More

Key Features

• Wide range input voltage
• Maximum power: up to 100 W at 230 Vac input
• STD5N52U power MOSFET (4.4 A, 520 V)
• Compatible with other power switches in DPAK packages (i.e. the STGD6NC60HD or STGDL6NC60DI)
• 15 V auxiliary power supply connector
• Motor control connector for interfacing with STM32-based control stages
• Three shunt resistor-based motor current sensing network
• Target applications: refrigerator compressors and dishwasher pumps
• RoHS compliant

Show More

Key Features

• Compact size
• Wide-range input voltage
• Maximum power up to 150 W at 230 Vac input
• STGD3HF60HD: 4.5 A, 600 V very fast IGBT
• Compatibility with other power switches in DPAK packages (the STD5N52U and STGD6NC60HD, for example)
• AC or DC bus voltage power supply connectors
• Connector for interfacing with the STM3210xx-EVAL board, STEVAL-IHM022V1, and STEVAL-IHM033V1 with alternate functions (current reference, current limitation/regulation, method selection, current boost)
• Efficient DC/DC power supply (15 V, 3.3 V)
• Suitable both for sinusoidal FOC and trapezoidal BLDC drive
• Single-shunt current reading topology with fast operational amplifier (with offset insertion for bipolar currents)
• Hardware overcurrent protection with boost capabilities
• Temperature sensor
• BEMF-detection network for BLDC drive
• Current regulation/limitation network for BLDC drive
• Hall sensor/quadrature encoder inputs

Show More

Key Features

• 3 A DC output current
• Operating input voltage from 5.5 V to 48 V
• 850 kHz internally fixed switching frequency
• Internal soft-start
• Internal current limiting
• Inhibit for zero current consumption
• 2 mA maximum quiescent current over-temperature range
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• Complete 100 W power inverter solution
• HV supply: 90 to 285 V AC or direct DC at 125 to 400 V DC
• Input inrush limiter based on NTC resistor
• Single shunt resistor current-sensing method
• Overtemperature and overcurrent hardware protection
• Compact and safe design
• Test points available to allow further evaluation
• RoHS compliant

Show More

Key Features

• Suitable for point-to-multipoint 2-way power line communication (PLC) over AC mains
• Flexible 2-board architecture:
  • EVALST7580-1, PLC board based on the ST7580 narrow-band FSK/PSK power line networking system-on-chip
  • EVLALTAIR900-M1, wide-range input voltage, 7.5 W power supply board based on the ALTAIR04-900 quasi-resonant current-mode SMPS controller
• STM32 microcontroller hosted on the EVALST7580-1 board to handle the ST7580 device and build a standalone power line node
• External access through several interface types: USB, SPI, I² C, USART, JTAG
• Opportunity to save and load data to/from an external μ-SD card
• Intuitive graphical user interface (GUI) for the Windows^® environment with fully programmable transceiver parameters
• Suitable for CENELEC EN50065 and FCC part 15 compliant applications

Show More

Key Features

• Extended AC input mains range: 115 or 230 VAC nominal at 50/60 Hz, or DC input voltage between 150 and 350 VDC
• Output current: 0.5 A_RMS to the motor
• Power stage: 3-phase inverter bridge implemented using the STGIPN3H60 SLLIMM-nano intelligent power module
• RoHS compliant

Show More

Key Features

• Maximum input voltage: 265 V AC or 375 V DC
• Minimum input voltage: 90 V AC or 128 V DC
• Output power for applied motor: up to 50 W
• +15 V auxiliary power supply based on the VIPER16 in a non-isolated buck configuration
• Compact design using the SLLIMM™-nano STGIPN3H60 consisting of 600 V IGBTs with gate drivers, op amp for current sensing and comparator
• Passive PFC circuit for power factor correction
• On-board infrared (IR) receiver/demodulator for speed and on/off control using IR remote
• External EEPROM M24C01 for recovery of last speed setting
• Hardware overcurrent protection
• Overtemperature protection with NTC thermistor
• Overvoltage and undervoltage detection
• Based on 32-bit ARM^® Cortex™-M3 core-based microcontroller STM32F100C6T6B
• Firmware based on STM32 PMSM FOC SDK 3.0 motor control firmware library and fully customized for the ceiling fan application
• FOC (field oriented control) sensorless algorithm
• PCB size customized for ceiling fan design
• PCB diameter: 105 mm
• Double-sided layout
• RoHS compliant

Show More