-
This family of 32-bit system-on-chip (SoC) microcontrollers is the latest achievement in integrated automotive application controllers. It belongs to an expanding family of automotive-focused products designed to address the next wave of body electronics applications within the vehicle.
The advanced and cost-efficient e200z0h host processor core of this automotive controller family complies with the Power Architecture technology and only implements the VLE (variable-length encoding) APU (Auxiliary Processor Unit), providing improved code density. It operates at speeds of up to 64 MHz and offers high performance processing optimized for low power consumption. It capitalizes on the available development infrastructure of current Power Architecture devices and is supported with software drivers, operating systems and configuration code to assist with users implementations.
Key Features
- High performance 64 MHz e200z0h CPU
- 32-bit Power Architecture®technology CPU
- Up to 60 DMIPs operation
- Variable length encoding (VLE)
- Memory
- Up to 1.5 MB on-chip Code Flash with ECC
- 64 KB on-chip Data Flash with ECC
- Up to 96 KB on-chip SRAM with ECC
- 8-entry MPU
- Interrupts
- 16 priority levels
- Non-maskable interrupt (NMI)
- Up to 51 external interrupts lines including 27 wake-up lines
- 16-channel eDMA (linked to PITs, DSPI, ADCs, eMIOS, LINFlex and I2C)
- GPIOs: 77 (LQFP100), 121 (LQFP144) and 149 (LQFP176)
- Timer units
- 8-channel 32-bit periodic interrupt timer
- 4-channel 32-bit system timer
- System watchdog timer
- Real-time clock timer
- eMIOS, 16-bit counter timed I/O units
- Up to 64 channels with PWM/MC/IC/OC
- Up to 10 counter basis
- ADC diagnostic trigger via CTU
- One 10-bit and one 12-bit ADC with up to 53 channels
- Extendable to 81 channels
- Individual conversion registers
- Cross triggering unit (CTU)
- Dedicated diagnostic module for lighting
- Advanced PWM generation
- Time-triggered diagnostics
- PWM-synchronized ADC measurements
- On-chip CAN/UART bootstrap loader
- Communications interfaces
- Up to 6 FlexCAN (2.0B active) with 64 message buffers each
- Up to 10 LINFlex/UART channels
- Up to 6 buffered DSPI channels
- I2C interface
- Clock generation
- 4 to 16 MHz fast external crystal oscillator
- 32 kHz slow external crystal oscillator
- 16 MHz fast internal RC oscillator
- 128 kHz slow internal RC oscillator for low-power modes
- Software-controlled FMPLL
- Clock monitoring unit
- Low-power capabilities
- Several low-power mode configurations
- Ultra-low-power standby with RTC and communication
- Fast wakeup schemes
- Exhaustive debugging capability
- Nexus 2+ interface on LBGA208 package
- Nexus 1 on all packages
- Voltage supply
- Single 5 V or 3.3 V supply
- On-chip voltage regulator
- External ballast resistor support
- LQFP100, LQFP144, and LQFP176 packages; LBGA208 package for Nexus2+
- Operating temperature range -40 to 125 °C
- High performance 64 MHz e200z0h CPU
Sample & Buy
| Part Number | Marketing Status | Packing Type | CPU Clock Frequency (MHz) (max) | Flash Size (kB) (Data) | Features set | Temperature (°C) | Budgetary Price (US$)* | Quantity | ECCN (US) | Country of Origin | More info | Order from Distributors | Order from ST | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| min | max | |||||||||||||
| SPC560B64L3B6E0X |
Active
|
Tape And Reel | 64 | 64 | - | -40 | 105 | 5.4 | 1000 | 3A991A2 | MALTA | No availability of distributors reported, please contact our sales office | ||
SPC560B64L3B6E0X
Marketing Status
ActivePacking Type
Tape And ReelUnit Price (US$)
5.4*(*) Suggested Resale Price per unit (USD) for BUDGETARY USE ONLY. For quotes, prices in local currency, please contact your local ST Sales Office  or our Distributors
Featured Videos
First Automotive MCUs introducing Phase Change Memory (PCM)
Design Tools
-
-
Picture Part number Manufacturer Description SEL-SPC5 -- Smart Selector for Micro 32bit Power Architecture products Part NumberSmart Selector for Micro 32bit Power Architecture products
-
Development Tools
-
-
Picture Part number Manufacturer Description CYCLONE P&E Microcomputer Systems Automated, Stand-Alone Production Programmer, Debug & Test. CYCLONE FX P&E Microcomputer Systems Automated, Stand-Alone Production Programmer, Debug & Test. DCI-GSI2 dSPACE dSPACE DCI-GSI2 is a low latency and high bandwidth on-chip debug interface for bypassing, calibration, measurement and flash programming. Multilink Universal P&E Microcomputer Systems Debug Probe for ARM and other devices. Multilink Universal FX for SPC5 P&E Microcomputer Systems High-Speed Debug Probe for ARM and other devices. PowerDebug JTAG Debugger Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. 
SPC5-CONNECT ST Programmable interface for PC communication to automotive target systems. 
SPC5-UDESTK ST USB/JTAG debugger for SPC5 MCUs with software license included (by PLS) TRACE32 PowerTools Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. UDE/UAD2next for SPC5 PLS UDE/UAD2next for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. UDE/UAD2pro for SPC5 PLS UDE/UAD2pro for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. UDE/UAD3+ for SPC5 PLS UDE/UAD3+ for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families. XETK calibration interface ETAS The Ethernet-based ETK, FETK and XETK interfaces provide direct access to the control variables and parameters of an ECU via the parallel data and address bus, or via a serial microcontroller testing or debugging interface. iC5000 On-chip Analyzer iSYSTEM iC5000 belongs to iSYSTEM's premium embedded development tool family for single and multi-core development and testing. iC5700 On-chip Analyzer iSYSTEM iC5700 is iSYSTEM's premium embedded development tool for complex single and multi-core development. iC6000 On-chip Analyzer with Aurora protocol support iSYSTEM iC6000 is iSYSTEM's premium embedded development solution supporting microcontrollers featuring the Aurora physical interface. Part NumberAutomated, Stand-Alone Production Programmer, Debug & Test.
Automated, Stand-Alone Production Programmer, Debug & Test.
dSPACE DCI-GSI2 is a low latency and high bandwidth on-chip debug interface for bypassing, calibration, measurement and flash programming.
Debug Probe for ARM and other devices.
High-Speed Debug Probe for ARM and other devices.
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
Programmable interface for PC communication to automotive target systems.
USB/JTAG debugger for SPC5 MCUs with software license included (by PLS)
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
UDE/UAD2next for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
UDE/UAD2pro for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
UDE/UAD3+ for SPC5 is a powerful and flexible debug, test and trace platform supporting multi-core microcontrollers of SPC57x/58x Power Architecture® device families.
The Ethernet-based ETK, FETK and XETK interfaces provide direct access to the control variables and parameters of an ECU via the parallel data and address bus, or via a serial microcontroller testing or debugging interface.
iC5000 belongs to iSYSTEM's premium embedded development tool family for single and multi-core development and testing.
iC5700 is iSYSTEM's premium embedded development tool for complex single and multi-core development.
iC6000 is iSYSTEM's premium embedded development solution supporting microcontrollers featuring the Aurora physical interface.
-
-
-
Picture Part number Manufacturer Description ASH/ETEC Ash Ware ETEC C Compiler Toolkit ASH/ETPU Ash Ware ETPU/ETPU2 Development Kit Arctic Studio - Development Tools ARCCORE AUTOSAR and embedded SW configuration. BYTE/eTPU Byte Craft eTPU_C Code Development System Diab Compiler Wind River The Proven Development Tool for Automotive Safety. EB tresos Studio - Development Tools Elektrobit AUTOSAR and embedded SW configuration. ECU Interface Software dSPACE dSPACE ECU Interface Software prepares ECUs, RCP Hardware and HIL Simulators for ECU Interfacing like bypassing, calibration, measurement and testing. ICDPPCNEXUS P&E Microcomputer Systems In-circuit debug software for SPC5 and similar devices. MULTI Integrated Development Environment Green Hills Software MULTI Integrated Development Environment MULTISPC56 Green Hills Software MULTI IDE PROGPPCNEXUS P&E Microcomputer Systems Flash programming software for SPC5 and similar devices. PowerView Debugger IDE Lauterbach Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc. SPC5-STUDIO ST Code Generator, Quick resources configurator and Eclipse development environment for SPC5 MCUs SPC5-UDEDEBG ST PLS JTAG debugger software full license or license renewal TargetLink dSPACE The production code generator dSPACE TargetLink generates highly efficient C code straight from MATLAB®/Simulink®/Stateflow®. UNITPPCNEXUS P&E Microcomputer Systems Interface library for SPC5-compatible PEmicro interfaces. WIND-WORKBENCH Wind River Wind River Workbench WinIDEASPC56 iSYSTEM winIDEA IDE isystem.connect iSYSTEM Automate your testing or other embedded debugging activitites with iSYSTEM's SDK. testIDEA iSYSTEM iSYSTEM's testing tools supporting original binary code testing on target together with their BlueBox™ On-Chip Analysers and iTAG Debuggers. winIDEA Open iSYSTEM iSYSTEM's integrated development environment (IDE) supporting its range of iTAG Debuggers for Cortex-M microcontrollers. Part NumberETEC C Compiler Toolkit
ETPU/ETPU2 Development Kit
AUTOSAR and embedded SW configuration.
eTPU_C Code Development System
The Proven Development Tool for Automotive Safety.
AUTOSAR and embedded SW configuration.
dSPACE ECU Interface Software prepares ECUs, RCP Hardware and HIL Simulators for ECU Interfacing like bypassing, calibration, measurement and testing.
In-circuit debug software for SPC5 and similar devices.
MULTI Integrated Development Environment
MULTI IDE
Flash programming software for SPC5 and similar devices.
Our product line TRACE32® supports technologies like JTAG, SWD, NEXUS or ETM with embedded debuggers, software and hardware trace and logic analyzer systems for over 3500 cores and CPUs within 250 families like ARM® Cortex®-A/-M/-R, PowerArchitecture, etc.
Code Generator, Quick resources configurator and Eclipse development environment for SPC5 MCUs
PLS JTAG debugger software full license or license renewal
The production code generator dSPACE TargetLink generates highly efficient C code straight from MATLAB®/Simulink®/Stateflow®.
Interface library for SPC5-compatible PEmicro interfaces.
Wind River Workbench
winIDEA IDE
Automate your testing or other embedded debugging activitites with iSYSTEM's SDK.
iSYSTEM's testing tools supporting original binary code testing on target together with their BlueBoxâ„¢ On-Chip Analysers and iTAG Debuggers.
iSYSTEM's integrated development environment (IDE) supporting its range of iTAG Debuggers for Cortex-M microcontrollers.
-
Embedded Software
-
-
Picture Part number Manufacturer Description CycurHSM ESCRYPT Powerful security software for your ECU. EB tresos Autocore SW Elektrobit AUTOSAR BSW components to be integrated with ST MCAL. K-SAR - AUTOSAR SUITE KPIT AUTOSAR and embedded SW configuration. ORIENTAIS - AUTOSAR SUITE ISOFT Infrastructure Software AUTOSAR and embedded SW configuration. RTA Solution ETAS AUTOSAR solutions for SPC5 32-bit Power Architecture Automotive MCU SPC5-CRYP-LIB -- Software Cryptography Library for SPC5 MCUs SPC56xMBP-FLASH ST Flash drivers for SPC56 M, B, C, D and P lines STSW-SPC56002FW ST LIN Drivers Libraries for SPC56 Microcontrollers Part NumberPowerful security software for your ECU.
AUTOSAR BSW components to be integrated with ST MCAL.
AUTOSAR and embedded SW configuration.
AUTOSAR and embedded SW configuration.
AUTOSAR solutions for SPC5 32-bit Power Architecture Automotive MCU
Software Cryptography Library for SPC5 MCUs
Flash drivers for SPC56 M, B, C, D and P lines
LIN Drivers Libraries for SPC56 Microcontrollers
-
Evaluation Tools
-
-
Picture Part number Manufacturer Description 
SPC56B-Discovery ST Discovery Kit for SPC56 B line - with SPC560B54L5 MCU Part NumberDiscovery Kit for SPC56 B line - with SPC560B54L5 MCU
-
Support and Applications
-
-
Picture Part number Manufacturer Description Design consultancy + Training Intecs Design consultancy and/or training on Automotive application with particular reference to AUTOSAR environment. Part NumberDesign consultancy and/or training on Automotive application with particular reference to AUTOSAR environment.
-
-
-
Picture Part number Manufacturer Description SPC56XX 32-Bit Single-Core Power Architecture Training MicroConsult Technical training and consulting for SPC560/SPC570/SPC580 Part NumberTechnical training and consulting for SPC560/SPC570/SPC580
-
| Part Number | Marketing Status | Package | Grade | RoHS Compliance Grade | Material Declaration** |
|---|---|---|---|---|---|
| SPC560B64L3B6E0X |
Active
|
LQFP 100 14x14x1.4 | Automotive | Ecopack2 |
|
SPC560B64L3B6E0X
Package:
LQFP 100 14x14x1.4Material Declaration**:
(**) The Material Declaration forms available on st.com may be generic documents based on the most commonly used package within a package family. For this reason, they may not be 100% accurate for a specific device. Please contact our sales support for information on specific devices.
