Control and Sensing

Key Features

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F103RET6 high-performance ARM Cortex^™ -M3 microcontroller
• Includes a DIL24 socket for easy MEMS adapter connection
• 3 V on-board linear voltage regulator
• DFU compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Debugging connector for SWD/JTAG
• RoHS compliant

Show More

Key Features

• First startup at Vin = 500 mV
• Input voltage working range: 150 mV ≤ Vin ≤ V_EOC
• End of charge battery voltage: V_EOC = 4.25 V
• Battery undervoltage protection: V_UVP = 3.7 V

Show More

Key Features

• Common features
  • STM32 microcontroller in LQFP64 package
  • 1 user LED shared with Arduino™
  • 1 user and 1 reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External SMPS to generate V_core logic supply
  • 24 MHz HSE
  • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI^® debug connector
  • Arm^® Mbed Enabled™ compliant

Show More

Key Features

• Contains the following ST sensors:
  • Pressure sensor LPS25HB
  • Humidity sensor HTS221
  • Accelerometer LIS3DH
  • Microphone MP34DT01
• AFE for processing the MP34DT01 microphone signal based on TSV522 low power, low offset op-amp
• Android app available
• RoHS compliant

Show More

Key Features

• AECQ100 qualification
• 1.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 45 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 5 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• AECQ100 qualification
• 0.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_{Q -SHTDWN}
• Adjustable f _SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 3.3 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 360 mΩ ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• AECQ100 qualification
• 0.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 45 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 5 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 360 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• AECQ100 qualification
• 0.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 μA I_Q at light load (LCM V_IN = 12 V and V_OUT =3.3 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 360 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• AECQ100 qualification
• 1.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 3.3 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• STM32F439IIH6 High Performance MCU ARM® Cortex™-M4F @ 180 MHz with 256 KB of embedded SRAM
• 8 MB external SRAM
• IMU 9 axes inertial sensor: LSM9DS1
• Environmental sensors: Pressure (LPS25HB), Humidity and Temperature (HTS221), UV index (UVIS25M).
• Proximity and ambient light sensors (2x VL6180X)
• Digital MEMS microphone array (4x MP34DT01)
• USB connector
• Micro SD card expansion
• GPIO expansion for pin control and connection to the STM32Nucleo board thanks to the adapter board included in the package

Show More

Key Features

• AECQ100 qualification
• 1.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 µA I_Q at light load (LCM V_IN = 12 V and V_OUT = 3.3 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

Key Features

• LSM6DSL MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±245/±500/±1000/±2000 dps)
• LSM303AGR MEMS 3D accelerometer (±2/±4/±8/±16 g) and MEMS3D magnetometer (±50 gauss)
• LPS22HB MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
• HTS221: capacitive digital relative humidity and temperature
• DIL24 socket for additional MEMS adapters and other sensors
• Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
• I²C sensor hub features on LSM6DSL available
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• RoHS compliant

Show More

Key Features

• Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
• Key features:
  • Low operating input voltage (from 1.4 V to 5.5 V)
  • Current capability from 200 mA to 300 mA
  • Low dropout (down to 160 mV typ.)
  • Ultra-low quiescent current (down to 500 nA typ.)
  • Low noise (down to 6.5 μVRMS typ.)
  • High PSSR (up to 80 dB)
  • Logic controlled electronic shutdown (enable)
  • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
• RoHS compliant

Show More

Key Features

• ST25DV64K dynamic NFC tag solution based on 64K-bit (8K-Byte) EEPROM and with I²C interface, Fast Transfer Mode and Energy Harvesting features
• STM32L031K6 ultra-low-power ARM Cortex-M0+ MCU running at 32 MHz with 32-Kbytes Flash and 8-Kbytes RAM
• LIS2DW12 ultra-low-power high-performance three-axis linear accelerometer
• LPS22HB ultra-compact piezo-resistive absolute pressure sensor which functions as a digital output barometer: 260-1260 hPa
• HTS221 capacitive digital sensor for relative humidity and temperature
• STLQ015 low drop linear regulator power management
• CR2032 Battery powered (not included)
• STM32Cube function pack (FP-SNS-SMARTAG1)
• Android (Google Play) and iOS demo apps (ST SmarTag)
• Suitable for the following applications:
  • Internet of Things
  • Supply Chain and Cold-Chain Management
  • Smart building, home and city
  • Retail and apparel
  • Smart packaging
  • Medical and pharmaceutical
  • Batteryless sensing
  • Smart agriculture (soil control, animal tracking, etc.)

Show More

Key Features

• First startup at Vin = 2.6 V
• Input voltage working range: 150 mV ≤ Vin ≤ 18 V
• End of charge battery voltage: V_EOC = 4.25 V
• Battery undervoltage protection: V_UVP = 3.7 V

Show More

Key Features

• SPV1050 based harvesting dongle board
• PV module soldered on the back
• Lithium coin cell battery
• PV module electrical characteristics at 200 lux:
  • VOC_TYP = 9.8 V, ISC_TYP = 20 μA
  • VMP_TYP = 8 V, IMP_TYP = 18 μA
• Li-Ion battery:
  • Capacity_NOM = 120 mAh
  • V_NOMINAL = 3.6 V
  • V_CHARGE = 4.2 V
  • V_{END-OF-DISCHARGE} = 2.75 V
• Interface to power monitoring board
• PV module voltage and battery monitoring
• Ambient light sensor for irradiance level measurement
• Supported by SW GUI to show MPPT accuracy and conversion efficiency

Show More

Key Features

• Common features
  • STM32 microcontroller in LQFP64 package
  • 1 user LED shared with Arduino™
  • 1 user and 1 reset push-buttons
  • 32.768 kHz crystal oscillator
  • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
  • Flexible power-supply options: ST-LINK, USB V_BUS or external sources
  • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs
• Board-specific features
  • External SMPS to generate V_core logic supply
  • 24 MHz HSE
  • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI^® debug connector
  • Arm^® Mbed Enabled™ compliant

Show More

Key Features

• Complete HTS221 pinout (SPI & I²C interface) for a standard DIL 24 socket
• Fully compatible with STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

Key Features

• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• 30 μA IQ at light load (LCM V_OUT = 3.3 V)
• 5 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_{DS(on) HS} = 180 mΩ, R_{DS(on) LS} = 110 mΩ
• Thermal shutdown

Show More

Key Features

• STM32L073VZI6 ultra-low-power Arm^® Cortex^® core-based microcontroller featuring 192 Kbytes of Flash memory and 20 Kbytes of RAM in LQFP100 package
• Four 5 V power supply options: power jack, ST-LINK USB connector, user USB FS connector, or daughterboard
• Selectable MCU voltage: 3.3 V or adjustable from 1.71 V to 3.6 V
• 2.8-inch color LCD-TFT with resistive touchscreen
• LCD glass 40 x 8 segments
• On-board current measurement
• IrDA transceiver
• Pressure sensor
• LC sensor metering
• Touch sensing linear sensor
• User and reset push-buttons
• 4-direction joystick with selection button
• Board connectors:
  • 2 RS-232 with DB9
  • USB with Micro-B
  • microSD™ card
• Board expansion connectors:
  • RF-EEPROM daughter board
  • Extension connector for daughter board or wrapping board
• On-board ST-LINK/V2-1 debugger/ programmer with USB re-enumeration capability: mass storage, virtual COM port and debug port
• Comprehensive free software libraries and examples available with the STM32Cube package.
• Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil^® and GCC-based IDEs

Show More

Key Features

• LSM6DS0: MEMS 3D accelerometer (±2/±4/±8 g) + 3D gyroscope (±245/±500/±2000 dps)
• LIS3MDL: MEMS 3D magnetometer (±4/ ±8/ ±12/ 16 gauss)
• LPS25HB*: MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
• HTS221: capacitive digital relative humidity and temperature
• DIL 24-pin socket available for additional MEMS adapters and other sensors (UV index)
• Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
• Compatible with STM32 Nucleo boards
• Equipped with Arduino UNO R3 connector
• RoHS compliant

Show More