Overview
Solutions
HW Evaluation Tools
Resources
Tools and Software
Key Products
Get Started

A valve regulates the flow of a media –  gases, liquids, granulates or fluidized solids – by opening, closing, or partially obstructing the passageway. Two types of valves are commonly used: shut-off valves allowing only either an open and closed state, and continuously adjustable valves which include proportional and throttle valves.

Size, energy-efficiency and reliability are key factors that must be taken into consideration by developers designing electronic valve control solutions.

We have a range of discrete power switches including MOSFETs, IGBTs and Triacs, intelligent power modules (IPM), monolithic intelligent power switches (IPS) and motor drivers as well as a large selection of 32-bit STM32 microcontrollers and humidity and temperature sensors as well as connectivity solutions for high-efficiency valve designs.

Part Number
Description
STEVAL-IFP010V3 High-side driver based on the VNI2140J Quick view

Key Features

  • Output current: 1 A per channel
  • Shorted-load protection
  • Junction overtemperature protection
  • Case overtemperature protection for thermal independence of the channels
  • Non-simultaneous TCSD (thermal case shutdown) restart for the various channels
  • Protection against loss of ground
  • Current limitation
  • Undervoltage shutdown
  • Open load in off-state and short to VCC detection
  • Open-drain diagnostic outputs
  • 3.3 V CMOS/TTL compatible inputs
  • Fast demagnetization of inductive loads
  • Conforms to IEC 61131-2 supply voltage: +4 V to +36 V
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA095V1 Up to 3 A step-down switching regulator based on the ST1S14 Quick view

Key Features

  • 3 A DC output current
  • Operating input voltage from 5.5 V to 48 V
  • 850 kHz internally fixed switching frequency
  • Internal soft-start
  • Internal current limiting
  • Inhibit for zero current consumption
  • 2 mA maximum quiescent current over-temperature range
  • Thermal shutdown
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP005V2 High side driver demonstration board based on the VN751PT Quick view

Key Features

  • RoHS compliant
  • Transil addition between TRIAC A2-G terminals
  • Overvoltage protection is not implemented on the board but some solder pads are available to implement it in two different ways:
  • Free development area with hole matrix available for application breadboard adaptation
  • 3 independent application programsHand dryer with infrared sensor and T1235H-6T switchBathroom fan with humidity sensor and ACS108 switchMulti-entrance room controller with push button and BTB08-600SW switch
  • Capacitive power supply (680 nF capacitor EPCOS B32923C36845 V ±10%Average output current: 16 mAStandby power losses < 0.3 W @ 230 V
  • Two potentiometers for setting sensor sensitivity and TRIAC turn-off delay
  • ICC connector for software adjustment
  • Varistor addition between mains voltage
  • Program selector (U2)

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IHM036V1 Low power motor control board featuring the SLLIMM™ STGIPN3H60 and MCU STM32F100C6T6B Quick view

Key Features

  • Complete 100 W power inverter solution
  • HV supply: 90 to 285 V AC or direct DC at 125 to 400 V DC
  • Input inrush limiter based on NTC resistor
  • Single shunt resistor current-sensing method
  • Overtemperature and overcurrent hardware protection
  • Compact and safe design
  • Test points available to allow further evaluation
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP020V1 High side driver based on L6370Q Quick view

Key Features

  • Single-channel topology
  • Galvanic isolation
  • 2.5 A output current
  • 9.5 V to 35 V supply voltage range
  • Short-circuit, overload, and thermal protections
  • Loss of ground and VS protections
  • Fast demagnetization of inductive loads
  • Open load, output short to VS detection
  • Two diagnostic outputs
  • Output status LED driver
  • EMC immunity against burst, surge, and ESD
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA099V1 3 A step-down switching demonstration board based on the L7986 in DFN10 package Quick view

Key Features

  • 3 A DC output current
  • From 4.5 V to 38 V range input voltage
  • Output voltage adjustable from 0.6 V
  • 250 kHz switching frequency programmable up to 1 MHz
  • Internal soft-start and enable
  • Low dropout operation: 100% duty cycle
  • Voltage feed-forward
  • Zero load current operation
  • Overcurrent and thermal protection
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IHM040V1 BLDC/PMSM driver demonstration board based on STM32 and the SLLIMM nano™ Quick view

Key Features

  • Extended AC input mains range: 115 or 230 VAC nominal at 50/60 Hz, or DC input voltage between 150 and 350 VDC
  • Output current: 0.5 ARMS to the motor
  • Power stage: 3-phase inverter bridge implemented using the STGIPN3H60 SLLIMM-nano intelligent power module
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM
STEVAL-IFP022V1 Eight-channel high-side driver based on the VNI8200XP Quick view

Key Features

  • Operating voltage: from 10.5 to 33 V
  • Operating current: 0.7 A for each channel
  • Reverse polarity protection
  • High-speed opto-isolation for SPI and parallel communication
  • Low-speed opto-isolation for device fault signaling
  • Step-down converter for 3.3 V or 5 V
  • Digital supply voltage
  • LED matrix for channel status signaling
  • Microcontroller interface
  • Designed to meet EMC standard requirements: IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IHM035V2 3-phase high voltage inverter power board for FOC and scalar motor control based on the STGIPN3H60 (SLLIMM™-nano) Quick view

Key Features

  • Nominal power: up to 100 W
  • Compatible with 3.3 V and 5 V control board
  • Single shunt resistor for current reading
  • On-board temperature sensor
  • Overcurrent protection with boost/disabling capability
  • For six-step drives:
    • Current limitation/regulation network
    • BEMF detection network
  • MC connector
  • Compatible with sinusoidal and trapezoidal control
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP015V2 ISO8200B High Side Driver - 8 Channels evaluation board Quick view

Key Features

  • VCC operating voltage from 10.5 to 33 V
  • 0.7 A for each channel
  • Reverse polarity protection on VCC and VDD supply voltage
  • Digital supply voltage VDD 3.3/5 V
  • Microcontroller interface direct/synchronous mode communication
  • Designed to meet requirements of IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5 standards
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IHM045V1 3-phase high voltage inverter power board for FOC based on the STGIPN3H60A (SLLIMM™-nano) Quick view

Key Features

  • Wide-range input voltage (30-270 Vac)
  • Maximum power up to 100 W at 230 Vac input
  • Based on the STGIPN3H60A SLLIMM™-nano AC motor drive
  • Mounts the VIPer06 fixed frequency offline converter from the VIPer™ plus family
  • Efficient DC-DC power supply (15 V, 3.3 V)
  • DC bus voltage power supply connectors
  • External 15 V input
  • Dedicated connector for interfacing with the various other ST evaluation boards
  • Suitable for sinusoidal FOC drives
  • Selectable single or three-shunt current reading topology with fast operational amplifier
  • Configurable for direct motor current sampling from shunt resistors
  • Hardware overcurrent detecting network
  • Temperature sensor
  • Hall sensor/quadrature encoder inputs
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA152V1 3.3 V/3 A high efficiency step down DC-DC converter (VIN= 4.5 to 60 V) based on the L7987 Quick view

Key Features

  • 3.3 V output voltage
  • 3 A DC output current
  • 4.5 V to 60 V input voltage
  • 500 kHz switching frequency
  • 3.5 ms programmed soft-start
  • VBIAS switch-over for improved efficiency at light load
  • 180° out of phase synchronization available
  • Open drain PGOOD available
  • Auto recovery overcurrent and thermal protection
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-MKI141V2 HTS221 humidity sensor adapter board for standard DIL24 socket (full pinout) Quick view

Key Features

  • Complete HTS221 pinout (SPI & I²C interface) for a standard DIL 24 socket
  • Fully compatible with STEVAL-MKI109V2 motherboard
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA158V1 38 V - 2 A synchronous step-down switching regulator evaluation board based on the A6986 Quick view

Key Features

  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • 30 µA IQ at light load (LCM VOUT = 3.3 V)
  • 5 µA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IHM06A1 Low voltage stepper motor driver expansion board based on the STSPIN220 for STM32 Nucleo Quick view

Key Features

  • Low voltage range: 1.8 to 10 V
  • Microstep adjustment up to the 256th step
  • Phase current: up to 1.3 ARMS
  • Current control with adjustable off-time
  • Full protection overcurrent and short circuit protection
  • Thermal shutdown
  • Compatible with Arduino UNO R3 connector
  • Compatible with STM32 Nucleo boards
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDS01A4 Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo Quick view

Key Features

  • STM32 Nucleo expansion board based on the SPSGRF-868
  • SPGRF-868 characteristics:
    • 868 MHz ETSI-certified module based on low power, low data-rate sub-1 GHz SPIRIT1 transceiver
    • Integrated Balun (BALF-SPI-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • Scalable solution; capable of cascading multiple boards for larger systems
  • Example firmware for point-to-point communication, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDS01A5 Sub-1 GHz RF expansion board based on the SPSGRF-915 module for STM32 Nucleo Quick view

Key Features

  • STM32 Nucleo expansion board based on the SPSGRF-915
  • X-NUCLEO-IDS01A5 contains FCC and IC certified module SPSGRF-915 (FCC ID: S9NSPSGRF and IC: 8976C-SPSGRF)
  • SPGRF-915:
    • 915 MHz FCC and IC certified module based on low-power, low-rate sub-1 GHz SPIRIT1 transceiver
    • Integrated Balun (BALF-SPI-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • Scalable solution; can cascade multiple boards for larger systems
  • Example firmware for point-to-point communication, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
EVAL6491HB Demonstration board for L6491 gate driver with smart shut down feature Quick view

Key Features

  • High voltage rail up to 600 V
  • dV/dt immunity: 50 V/ns in full temperature range
  • Driver current capability: 4 A source/sink
  • Comparator for fault protections
  • Smart shutdown function
  • Integrated bootstrap diode
  • Adjustable deadtime
  • Interlocking function
  • Switching times 15 ns rise/fall with 1 nF load
  • 3.3 V, 5 V TTL/CMOS inputs with hysteresis
  • Compact and simplified layout
  • Bill of material reduction
  • Effective fault protection
  • Flexible, easy and fast design

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDB05A1 Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo Quick view

Key Features

  • STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
  • X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
  • SPBTLE-RF:
    • Bluetooth Low Energy FCC and IC certified module based on Bluetooth® SMART 4.1 network processor BlueNRG-MS
    • Integrated Balun (BALF-NRG-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-OUT01A1 Industrial Digital output expansion board based on ISO8200BQ for STM32 Nucleo Quick view

Key Features

  • Enables industrial programmable logic controller (PLC) capabilities on STM32 Nucleo
  • ISO8200BQ galvanic isolated octal high-side smart power solid state-relay
  • Operating voltage from 10.5 V to 33 V
  • Maximum operating output current per channel IOUT = 700 mA
  • Status LEDs: Fault, Thermal protection
  • Compatible with Arduino® UNO R3 connector
  • Compliance with EMC standards:
    • IEC61000-4-2: 8kV Contact Discharge and 15kV Air discharge
    • IEC61000-4-3: 4kV Discharge on output and supply line
    • IEC61000-4-5: 2kV Discharge on output and supply line
  • Compatible with STM32 Nucleo boards
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP028V1 Single high side driver based on IPS160H Quick view

Key Features

  • Operating voltage from 8 to 60 V
  • Operating current up to 2.5 A
  • Programmable cut-off delay time
  • Reverse polarity protection
  • Galvanic isolation on PCB
  • Input pins compatible with VCC rails
  • Green LED for channel ON/OFF status
  • Red LED for common diagnostics on:
    • Open load in OFF state
    • Cut-off
    • Thermal protection
    • Red LED functionality on DIAG pin guaranteed from VCC = 12 V
  • Microcontroller interface
  • IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5 compliant
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IHM13A1 Low voltage brush DC motor driver expansion board for STM32 Nucleo based on the STSPIN250 Quick view

Key Features

  • Low voltage range from 1.8 V to 10 V
  • Current up to 2.6 A r.m.s.
  • Current control with adjustable off-time
  • Full overcurrent and short circuit protection
  • Thermal shutdown
  • Compatible with Arduino UNO R3 connector
  • Compatible with STM32 Nucleo boards
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP034V1 Single high side driver based on IPS161H Quick view

Key Features

  • Operating voltage range: 8 to 60 V
  • Operating current: 0.5 A max
  • Programmable cut-off delay time
  • Reverse polarity protection
  • Galvanic isolation on PCB
  • Input pins compatible with VCC rails
  • Green LED for channel ON/OFF status
  • Red LED for Common Diagnostics on:
    • open load in OFF state
    • cut-off
    • thermal protection
  • Microcontroller interface
  • Compliant with IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI915V1 Sub-1GHz transceiver development kit based on S2-LP Quick view

Key Features

  • S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
  • STM32 Nucleo-64 development board with STM32L152RE MCU
  • Suitable for wireless M-Bus systems
  • Suitable for SigFox applications
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +27 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
EVALSTDRV600HB8 Demonstration board kit for L638xE and L639x high-voltage gate drivers Quick view

Key Features

  • Half-bridge configuration
  • High voltage rail up to 600 V
  • Includes samples of each compatible gate driver in SO8 package
    • L6385E, L6387E, L6388E, L6389E,
    • L6395, L6398, L6399
  • Compatible with MOSFETs/IGBTs in
    • DPAK, D2PAK, TO-220, TO-220FP
  • dV/dt transient immunity ± 50 V/ns in full temperature range
  • Integrated bootstrap diode
  • Dedicated high- and low-side driving inputs
  • Compact and simplified layout
  • Gate drivers in the kit features different functionalities and characteristics
    • UVLO on both - high-side and low-side
    • Internal deadtime, or no deadtime
    • Interlocking for anti cross-conduction protection
    • Ability to drive asymmetrical half-bridges and switched reluctance motors
    • Active high or active low LIN for single input gate driving

Show More

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IDB007V1M Evaluation platform based on the SPBTLE-1S module Quick view

Key Features

  • Bluetooth® SMART board with the SPBTLE-1S certified module based on the BlueNRG-1 Bluetooth low energy system-on-chip
  • Associated BlueNRG-1 development kit SW package including firmware and documentation
  • Up to +5 dBm available output power
  • Bluetooth® low energy v4.2 compliant, supports master, slave and simultaneous master-and-slave roles
  • Integrated balun which integrates a matching network and harmonics filter
  • SMA connector for antenna or measuring equipment
  • 3 user LEDs
  • 2 user buttons
  • 3D digital accelerometer and 3D digital gyroscope
  • MEMS pressure sensor with embedded temperature sensor
  • Battery holder
  • JTAG debug connector
  • USB to serial bridge for providing I/O channel with the BlueNRG-1 device
  • Jumper for measuring current for BlueNRG-1 only
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IPMNG8Q 600 W motor control power board based on STGIPQ8C60T-HZ SLLIMM™-nano IPM Quick view

Key Features

  • Input voltage: from 125 to 400 VDC
  • Nominal power: up to 600 W
  • Nominal current: up to 4.8 Arms
  • Input auxiliary voltage: up to 20 VDC
  • Single- or three-shunt resistors for current sensing (with sensing network)
  • Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
  • Overcurrent hardware protection
  • IPM temperature monitoring and protection
  • Hall sensor or encoder input
  • IGBT intelligent power module:
    • 2nd series SLLIMM-nano IPM (STGIPQ8C60T-HZ – full molded package)
  • Motor control connector (32 pins) interfacing with ST MCU boards
  • Universal design for further evaluation with bread board and testing pins
  • Very compact size
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IPMNM1N 60 W motor control power board based on STIPN1M50T-H SLLIMM™nano IPM MOSFET Quick view

Key Features

  • Input voltage: from 125 to 400 VDC
  • Nominal power: up to 60 W
  • Nominal current: up to 0.35 Arms
  • Input auxiliary voltage: up to 20 VDC
  • Single- or three-shunt resistors for current sensing (with sensing network)
  • Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
  • Overcurrent hardware protection
  • IPM temperature monitoring and protection
  • Hall sensor or encoder input
  • Intelligent power module:
    • SLLIMM-nano IPM MOSFET-based (STIPN1M50T-H – full molded package)
  • Motor control connector (32 pins) interfacing with ST MCU boards
  • Universal design for further evaluation with bread board and testing pins
  • Very compact size
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IPMNM2N 100 W motor control power board based on STIPN2M50T-H SLLIMM™nano IPM MOSFET Quick view

Key Features

  • Input voltage: from 125 to 400 VDC
  • Nominal power: up to 100 W
  • Nominal current: up to 0.6 Arms
  • Input auxiliary voltage: up to 20 VDC
  • Single- or three-shunt resistors for current sensing (with sensing network)
  • Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
  • Overcurrent hardware protection
  • IPM temperature monitoring and protection
  • Hall sensor or encoder input
  • Intelligent power module:
    • SLLIMM-nano IPM MOSFET-based (STIPN2M50T-H – full molded package)
  • Motor control connector (32 pins) interfacing with ST MCU boards
  • Universal design for further evaluation with bread board and testing pins
  • Very compact size
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IDB008V2 Evaluation platform based on the BlueNRG-2 Quick view

Key Features

  • Bluetooth® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
  • Associated BlueNRG-2 development kit SW package including firmware and documentation
  • Up to +8 dBm available output power (at antenna connector)
  • Excellent receiver sensitivity (-88 dBm)
  • Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
  • Bluetooth® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
  • New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
  • SMA connector for antenna or measuring equipment
  • 3 user LEDs
  • 2 user buttons
  • 3D digital accelerometer and 3D digital gyroscope
  • MEMS pressure sensor with embedded temperature sensor
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IHM17M1 Low voltage three-phase brushless DC motor driver expansion board based on STSPIN233 for STM32 Nucleo Quick view

Key Features

  • Low voltage range from 1.8 V to 10 V
  • Current up to 1.3 Arms
  • Full overcurrent protection and short-circuit protection
  • Thermal shutdown
  • Compatible with STM32 Nucleo boards
  • Equipped with ST morpho connectors
  • Hall/Encoder motor sensor connector and circuit
  • Potentiometer available for speed regulation
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
EVALKITSTKNX Miniature transceiver STKNX evaluation and development kit Quick view

Key Features

  • Full KNX twisted pair device development kit based on the STKNX miniature transceiver
  • Controlled by STM32F103 microcontroller 32-bit Cortex® -M3 - 16 MHz - 128 kB Flash
  • Twisted pair TP1-256 support
  • Compatible with ETS engineering tool software
  • Test firmware already downloaded in the board to demonstrate features
  • Includes originally TAPKO KNX protocol stack KAIstack
  • Supported development environments: AC6 OpenSTM32 (Linux® , Windows® and Mac OS-X) or Atollic TrueSTUDIO® (Linux and Windows)
  • JTAG debug through isolated USB host interface (ST-LINK/V2-1 on-board)
  • Standard serial wire debug (SWD) and JTAG interfaces available on standard HE10 20-pin connector
  • Connectors for extension board compatible with Arduino™ and ST Morpho standards
  • UART through isolated USB host interface for connecting a PC
  • No external supply needed during SW development in “desktop mode” (KNX disconnected), USB supply only
  • Power supply flexibility exploiting whole supplies options offered by STKNX
  • 1 button and 1 LED for KNX programming
  • 4 buttons and 4 LEDs for basic KNX sensors and actuators emulation
  • Optional 32.768 kHz crystal for RTC mode
  • Optional CPU reset control from STKNX
  • STKNX area routed on 2 PCB layers only, for reference layout
  • Compliant with bus family standard EN 50491
  • Complete reference design suitable to implement products compatibles with KNX standards:
    • CENELEC EN 50090 (EU HBES)
    • CEN EN 13321-1/2 (EU BA)
    • ISO/IEC 14543-3 (World HES)
    • GB/T 20965 (Chinese HBC)
    • ANSI/ASHRAE Standard 135 (USA)
  • Includes optional isolation mode for developing SELV product according to EN 61140
  • Operating temperature range -40 °C to +85 °C

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI868V2 Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP Quick view

Key Features

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for Wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX @ +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission, and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI433V2 Sub-1GHz (430-470 MHz) transceiver development kit based on S2-LP Quick view

Key Features

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF module tuned for 430-470 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX at +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-OUT02A1 Industrial digital output expansion board based on ISO8200AQ for STM32 Nucleo Quick view

Key Features

  • Based on the ISO8200AQ whose main characteristics are:
    • Embedded 4kV galvanic isolation
    • Radio frequency communication between the logic and process sides for maximum noise immunity
    • Very low power dissipation (RON(MAX) = 220 mΩ)
    • Fast decay for inductive loads
    • 20 MHz SPI I/F on logic side
    • VCC power good diagnostics
    • Overload and overheating protections with thermal shutdown and diagnostics
    • QFN-32L (9x11x1 mm) package
  • 10.5 to 33 V operating voltage range
  • Green LED (x8) for output on/off status
  • Red LED for process supply power good fault
  • Red LED for overload and overheating
  • Supply reverse polarity protection
  • EMC compliance according to IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino™ UNO R3 connectors
  • CE certified
  • RoHS and China RoHS compliant
  • WEEE compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
Part Number
STEVAL-IFP010V3

High-side driver based on the VNI2140J

Key Features

  • Output current: 1 A per channel
  • Shorted-load protection
  • Junction overtemperature protection
  • Case overtemperature protection for thermal independence of the channels
  • Non-simultaneous TCSD (thermal case shutdown) restart for the various channels
  • Protection against loss of ground
  • Current limitation
  • Undervoltage shutdown
  • Open load in off-state and short to VCC detection
  • Open-drain diagnostic outputs
  • 3.3 V CMOS/TTL compatible inputs
  • Fast demagnetization of inductive loads
  • Conforms to IEC 61131-2 supply voltage: +4 V to +36 V
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA095V1

Up to 3 A step-down switching regulator based on the ST1S14

Key Features

  • 3 A DC output current
  • Operating input voltage from 5.5 V to 48 V
  • 850 kHz internally fixed switching frequency
  • Internal soft-start
  • Internal current limiting
  • Inhibit for zero current consumption
  • 2 mA maximum quiescent current over-temperature range
  • Thermal shutdown
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP005V2

High side driver demonstration board based on the VN751PT

Key Features

  • RoHS compliant
  • Transil addition between TRIAC A2-G terminals
  • Overvoltage protection is not implemented on the board but some solder pads are available to implement it in two different ways:
  • Free development area with hole matrix available for application breadboard adaptation
  • 3 independent application programsHand dryer with infrared sensor and T1235H-6T switchBathroom fan with humidity sensor and ACS108 switchMulti-entrance room controller with push button and BTB08-600SW switch
  • Capacitive power supply (680 nF capacitor EPCOS B32923C36845 V ±10%Average output current: 16 mAStandby power losses < 0.3 W @ 230 V
  • Two potentiometers for setting sensor sensitivity and TRIAC turn-off delay
  • ICC connector for software adjustment
  • Varistor addition between mains voltage
  • Program selector (U2)

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IHM036V1

Low power motor control board featuring the SLLIMM™ STGIPN3H60 and MCU STM32F100C6T6B

Key Features

  • Complete 100 W power inverter solution
  • HV supply: 90 to 285 V AC or direct DC at 125 to 400 V DC
  • Input inrush limiter based on NTC resistor
  • Single shunt resistor current-sensing method
  • Overtemperature and overcurrent hardware protection
  • Compact and safe design
  • Test points available to allow further evaluation
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP020V1

High side driver based on L6370Q

Key Features

  • Single-channel topology
  • Galvanic isolation
  • 2.5 A output current
  • 9.5 V to 35 V supply voltage range
  • Short-circuit, overload, and thermal protections
  • Loss of ground and VS protections
  • Fast demagnetization of inductive loads
  • Open load, output short to VS detection
  • Two diagnostic outputs
  • Output status LED driver
  • EMC immunity against burst, surge, and ESD
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA099V1

3 A step-down switching demonstration board based on the L7986 in DFN10 package

Key Features

  • 3 A DC output current
  • From 4.5 V to 38 V range input voltage
  • Output voltage adjustable from 0.6 V
  • 250 kHz switching frequency programmable up to 1 MHz
  • Internal soft-start and enable
  • Low dropout operation: 100% duty cycle
  • Voltage feed-forward
  • Zero load current operation
  • Overcurrent and thermal protection
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IHM040V1

BLDC/PMSM driver demonstration board based on STM32 and the SLLIMM nano™

Key Features

  • Extended AC input mains range: 115 or 230 VAC nominal at 50/60 Hz, or DC input voltage between 150 and 350 VDC
  • Output current: 0.5 ARMS to the motor
  • Power stage: 3-phase inverter bridge implemented using the STGIPN3H60 SLLIMM-nano intelligent power module
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM
STEVAL-IFP022V1

Eight-channel high-side driver based on the VNI8200XP

Key Features

  • Operating voltage: from 10.5 to 33 V
  • Operating current: 0.7 A for each channel
  • Reverse polarity protection
  • High-speed opto-isolation for SPI and parallel communication
  • Low-speed opto-isolation for device fault signaling
  • Step-down converter for 3.3 V or 5 V
  • Digital supply voltage
  • LED matrix for channel status signaling
  • Microcontroller interface
  • Designed to meet EMC standard requirements: IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IHM035V2

3-phase high voltage inverter power board for FOC and scalar motor control based on the STGIPN3H60 (SLLIMM™-nano)

Key Features

  • Nominal power: up to 100 W
  • Compatible with 3.3 V and 5 V control board
  • Single shunt resistor for current reading
  • On-board temperature sensor
  • Overcurrent protection with boost/disabling capability
  • For six-step drives:
    • Current limitation/regulation network
    • BEMF detection network
  • MC connector
  • Compatible with sinusoidal and trapezoidal control
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP015V2

ISO8200B High Side Driver - 8 Channels evaluation board

Key Features

  • VCC operating voltage from 10.5 to 33 V
  • 0.7 A for each channel
  • Reverse polarity protection on VCC and VDD supply voltage
  • Digital supply voltage VDD 3.3/5 V
  • Microcontroller interface direct/synchronous mode communication
  • Designed to meet requirements of IEC 61000-4-2, IEC 61000-4-4, IEC 61000-4-5 standards
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IHM045V1

3-phase high voltage inverter power board for FOC based on the STGIPN3H60A (SLLIMM™-nano)

Key Features

  • Wide-range input voltage (30-270 Vac)
  • Maximum power up to 100 W at 230 Vac input
  • Based on the STGIPN3H60A SLLIMM™-nano AC motor drive
  • Mounts the VIPer06 fixed frequency offline converter from the VIPer™ plus family
  • Efficient DC-DC power supply (15 V, 3.3 V)
  • DC bus voltage power supply connectors
  • External 15 V input
  • Dedicated connector for interfacing with the various other ST evaluation boards
  • Suitable for sinusoidal FOC drives
  • Selectable single or three-shunt current reading topology with fast operational amplifier
  • Configurable for direct motor current sampling from shunt resistors
  • Hardware overcurrent detecting network
  • Temperature sensor
  • Hall sensor/quadrature encoder inputs
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA152V1

3.3 V/3 A high efficiency step down DC-DC converter (VIN= 4.5 to 60 V) based on the L7987

Key Features

  • 3.3 V output voltage
  • 3 A DC output current
  • 4.5 V to 60 V input voltage
  • 500 kHz switching frequency
  • 3.5 ms programmed soft-start
  • VBIAS switch-over for improved efficiency at light load
  • 180° out of phase synchronization available
  • Open drain PGOOD available
  • Auto recovery overcurrent and thermal protection
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-MKI141V2

HTS221 humidity sensor adapter board for standard DIL24 socket (full pinout)

Key Features

  • Complete HTS221 pinout (SPI & I²C interface) for a standard DIL 24 socket
  • Fully compatible with STEVAL-MKI109V2 motherboard
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-ISA158V1

38 V - 2 A synchronous step-down switching regulator evaluation board based on the A6986

Key Features

  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • 30 µA IQ at light load (LCM VOUT = 3.3 V)
  • 5 µA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IHM06A1

Low voltage stepper motor driver expansion board based on the STSPIN220 for STM32 Nucleo

Key Features

  • Low voltage range: 1.8 to 10 V
  • Microstep adjustment up to the 256th step
  • Phase current: up to 1.3 ARMS
  • Current control with adjustable off-time
  • Full protection overcurrent and short circuit protection
  • Thermal shutdown
  • Compatible with Arduino UNO R3 connector
  • Compatible with STM32 Nucleo boards
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDS01A4

Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo

Key Features

  • STM32 Nucleo expansion board based on the SPSGRF-868
  • SPGRF-868 characteristics:
    • 868 MHz ETSI-certified module based on low power, low data-rate sub-1 GHz SPIRIT1 transceiver
    • Integrated Balun (BALF-SPI-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • Scalable solution; capable of cascading multiple boards for larger systems
  • Example firmware for point-to-point communication, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDS01A5

Sub-1 GHz RF expansion board based on the SPSGRF-915 module for STM32 Nucleo

Key Features

  • STM32 Nucleo expansion board based on the SPSGRF-915
  • X-NUCLEO-IDS01A5 contains FCC and IC certified module SPSGRF-915 (FCC ID: S9NSPSGRF and IC: 8976C-SPSGRF)
  • SPGRF-915:
    • 915 MHz FCC and IC certified module based on low-power, low-rate sub-1 GHz SPIRIT1 transceiver
    • Integrated Balun (BALF-SPI-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connectors
  • Scalable solution; can cascade multiple boards for larger systems
  • Example firmware for point-to-point communication, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
EVAL6491HB

Demonstration board for L6491 gate driver with smart shut down feature

Key Features

  • High voltage rail up to 600 V
  • dV/dt immunity: 50 V/ns in full temperature range
  • Driver current capability: 4 A source/sink
  • Comparator for fault protections
  • Smart shutdown function
  • Integrated bootstrap diode
  • Adjustable deadtime
  • Interlocking function
  • Switching times 15 ns rise/fall with 1 nF load
  • 3.3 V, 5 V TTL/CMOS inputs with hysteresis
  • Compact and simplified layout
  • Bill of material reduction
  • Effective fault protection
  • Flexible, easy and fast design

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IDB05A1

Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo

Key Features

  • STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
  • X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
  • SPBTLE-RF:
    • Bluetooth Low Energy FCC and IC certified module based on Bluetooth® SMART 4.1 network processor BlueNRG-MS
    • Integrated Balun (BALF-NRG-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-OUT01A1

Industrial Digital output expansion board based on ISO8200BQ for STM32 Nucleo

Key Features

  • Enables industrial programmable logic controller (PLC) capabilities on STM32 Nucleo
  • ISO8200BQ galvanic isolated octal high-side smart power solid state-relay
  • Operating voltage from 10.5 V to 33 V
  • Maximum operating output current per channel IOUT = 700 mA
  • Status LEDs: Fault, Thermal protection
  • Compatible with Arduino® UNO R3 connector
  • Compliance with EMC standards:
    • IEC61000-4-2: 8kV Contact Discharge and 15kV Air discharge
    • IEC61000-4-3: 4kV Discharge on output and supply line
    • IEC61000-4-5: 2kV Discharge on output and supply line
  • Compatible with STM32 Nucleo boards
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP028V1

Single high side driver based on IPS160H

Key Features

  • Operating voltage from 8 to 60 V
  • Operating current up to 2.5 A
  • Programmable cut-off delay time
  • Reverse polarity protection
  • Galvanic isolation on PCB
  • Input pins compatible with VCC rails
  • Green LED for channel ON/OFF status
  • Red LED for common diagnostics on:
    • Open load in OFF state
    • Cut-off
    • Thermal protection
    • Red LED functionality on DIAG pin guaranteed from VCC = 12 V
  • Microcontroller interface
  • IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5 compliant
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IHM13A1

Low voltage brush DC motor driver expansion board for STM32 Nucleo based on the STSPIN250

Key Features

  • Low voltage range from 1.8 V to 10 V
  • Current up to 2.6 A r.m.s.
  • Current control with adjustable off-time
  • Full overcurrent and short circuit protection
  • Thermal shutdown
  • Compatible with Arduino UNO R3 connector
  • Compatible with STM32 Nucleo boards
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IFP034V1

Single high side driver based on IPS161H

Key Features

  • Operating voltage range: 8 to 60 V
  • Operating current: 0.5 A max
  • Programmable cut-off delay time
  • Reverse polarity protection
  • Galvanic isolation on PCB
  • Input pins compatible with VCC rails
  • Green LED for channel ON/OFF status
  • Red LED for Common Diagnostics on:
    • open load in OFF state
    • cut-off
    • thermal protection
  • Microcontroller interface
  • Compliant with IEC 61000-4-2, IEC61000-4-4 and IEC 61000-4-5
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI915V1

Sub-1GHz transceiver development kit based on S2-LP

Key Features

  • S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
  • STM32 Nucleo-64 development board with STM32L152RE MCU
  • Suitable for wireless M-Bus systems
  • Suitable for SigFox applications
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +27 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
EVALSTDRV600HB8

Demonstration board kit for L638xE and L639x high-voltage gate drivers

Key Features

  • Half-bridge configuration
  • High voltage rail up to 600 V
  • Includes samples of each compatible gate driver in SO8 package
    • L6385E, L6387E, L6388E, L6389E,
    • L6395, L6398, L6399
  • Compatible with MOSFETs/IGBTs in
    • DPAK, D2PAK, TO-220, TO-220FP
  • dV/dt transient immunity ± 50 V/ns in full temperature range
  • Integrated bootstrap diode
  • Dedicated high- and low-side driving inputs
  • Compact and simplified layout
  • Gate drivers in the kit features different functionalities and characteristics
    • UVLO on both - high-side and low-side
    • Internal deadtime, or no deadtime
    • Interlocking for anti cross-conduction protection
    • Ability to drive asymmetrical half-bridges and switched reluctance motors
    • Active high or active low LIN for single input gate driving

Show More

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IDB007V1M

Evaluation platform based on the SPBTLE-1S module

Key Features

  • Bluetooth® SMART board with the SPBTLE-1S certified module based on the BlueNRG-1 Bluetooth low energy system-on-chip
  • Associated BlueNRG-1 development kit SW package including firmware and documentation
  • Up to +5 dBm available output power
  • Bluetooth® low energy v4.2 compliant, supports master, slave and simultaneous master-and-slave roles
  • Integrated balun which integrates a matching network and harmonics filter
  • SMA connector for antenna or measuring equipment
  • 3 user LEDs
  • 2 user buttons
  • 3D digital accelerometer and 3D digital gyroscope
  • MEMS pressure sensor with embedded temperature sensor
  • Battery holder
  • JTAG debug connector
  • USB to serial bridge for providing I/O channel with the BlueNRG-1 device
  • Jumper for measuring current for BlueNRG-1 only
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IPMNG8Q

600 W motor control power board based on STGIPQ8C60T-HZ SLLIMM™-nano IPM

Key Features

  • Input voltage: from 125 to 400 VDC
  • Nominal power: up to 600 W
  • Nominal current: up to 4.8 Arms
  • Input auxiliary voltage: up to 20 VDC
  • Single- or three-shunt resistors for current sensing (with sensing network)
  • Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
  • Overcurrent hardware protection
  • IPM temperature monitoring and protection
  • Hall sensor or encoder input
  • IGBT intelligent power module:
    • 2nd series SLLIMM-nano IPM (STGIPQ8C60T-HZ – full molded package)
  • Motor control connector (32 pins) interfacing with ST MCU boards
  • Universal design for further evaluation with bread board and testing pins
  • Very compact size
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IPMNM1N

60 W motor control power board based on STIPN1M50T-H SLLIMM™nano IPM MOSFET

Key Features

  • Input voltage: from 125 to 400 VDC
  • Nominal power: up to 60 W
  • Nominal current: up to 0.35 Arms
  • Input auxiliary voltage: up to 20 VDC
  • Single- or three-shunt resistors for current sensing (with sensing network)
  • Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
  • Overcurrent hardware protection
  • IPM temperature monitoring and protection
  • Hall sensor or encoder input
  • Intelligent power module:
    • SLLIMM-nano IPM MOSFET-based (STIPN1M50T-H – full molded package)
  • Motor control connector (32 pins) interfacing with ST MCU boards
  • Universal design for further evaluation with bread board and testing pins
  • Very compact size
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IPMNM2N

100 W motor control power board based on STIPN2M50T-H SLLIMM™nano IPM MOSFET

Key Features

  • Input voltage: from 125 to 400 VDC
  • Nominal power: up to 100 W
  • Nominal current: up to 0.6 Arms
  • Input auxiliary voltage: up to 20 VDC
  • Single- or three-shunt resistors for current sensing (with sensing network)
  • Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU
  • Overcurrent hardware protection
  • IPM temperature monitoring and protection
  • Hall sensor or encoder input
  • Intelligent power module:
    • SLLIMM-nano IPM MOSFET-based (STIPN2M50T-H – full molded package)
  • Motor control connector (32 pins) interfacing with ST MCU boards
  • Universal design for further evaluation with bread board and testing pins
  • Very compact size
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-IDB008V2

Evaluation platform based on the BlueNRG-2

Key Features

  • Bluetooth® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
  • Associated BlueNRG-2 development kit SW package including firmware and documentation
  • Up to +8 dBm available output power (at antenna connector)
  • Excellent receiver sensitivity (-88 dBm)
  • Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
  • Bluetooth® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
  • New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
  • SMA connector for antenna or measuring equipment
  • 3 user LEDs
  • 2 user buttons
  • 3D digital accelerometer and 3D digital gyroscope
  • MEMS pressure sensor with embedded temperature sensor
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-IHM17M1

Low voltage three-phase brushless DC motor driver expansion board based on STSPIN233 for STM32 Nucleo

Key Features

  • Low voltage range from 1.8 V to 10 V
  • Current up to 1.3 Arms
  • Full overcurrent protection and short-circuit protection
  • Thermal shutdown
  • Compatible with STM32 Nucleo boards
  • Equipped with ST morpho connectors
  • Hall/Encoder motor sensor connector and circuit
  • Potentiometer available for speed regulation
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
EVALKITSTKNX

Miniature transceiver STKNX evaluation and development kit

Key Features

  • Full KNX twisted pair device development kit based on the STKNX miniature transceiver
  • Controlled by STM32F103 microcontroller 32-bit Cortex® -M3 - 16 MHz - 128 kB Flash
  • Twisted pair TP1-256 support
  • Compatible with ETS engineering tool software
  • Test firmware already downloaded in the board to demonstrate features
  • Includes originally TAPKO KNX protocol stack KAIstack
  • Supported development environments: AC6 OpenSTM32 (Linux® , Windows® and Mac OS-X) or Atollic TrueSTUDIO® (Linux and Windows)
  • JTAG debug through isolated USB host interface (ST-LINK/V2-1 on-board)
  • Standard serial wire debug (SWD) and JTAG interfaces available on standard HE10 20-pin connector
  • Connectors for extension board compatible with Arduino™ and ST Morpho standards
  • UART through isolated USB host interface for connecting a PC
  • No external supply needed during SW development in “desktop mode” (KNX disconnected), USB supply only
  • Power supply flexibility exploiting whole supplies options offered by STKNX
  • 1 button and 1 LED for KNX programming
  • 4 buttons and 4 LEDs for basic KNX sensors and actuators emulation
  • Optional 32.768 kHz crystal for RTC mode
  • Optional CPU reset control from STKNX
  • STKNX area routed on 2 PCB layers only, for reference layout
  • Compliant with bus family standard EN 50491
  • Complete reference design suitable to implement products compatibles with KNX standards:
    • CENELEC EN 50090 (EU HBES)
    • CEN EN 13321-1/2 (EU BA)
    • ISO/IEC 14543-3 (World HES)
    • GB/T 20965 (Chinese HBC)
    • ANSI/ASHRAE Standard 135 (USA)
  • Includes optional isolation mode for developing SELV product according to EN 61140
  • Operating temperature range -40 °C to +85 °C

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI868V2

Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP

Key Features

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for Wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX @ +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission, and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
STEVAL-FKI433V2

Sub-1GHz (430-470 MHz) transceiver development kit based on S2-LP

Key Features

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF module tuned for 430-470 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX at +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
X-NUCLEO-OUT02A1

Industrial digital output expansion board based on ISO8200AQ for STM32 Nucleo

Key Features

  • Based on the ISO8200AQ whose main characteristics are:
    • Embedded 4kV galvanic isolation
    • Radio frequency communication between the logic and process sides for maximum noise immunity
    • Very low power dissipation (RON(MAX) = 220 mΩ)
    • Fast decay for inductive loads
    • 20 MHz SPI I/F on logic side
    • VCC power good diagnostics
    • Overload and overheating protections with thermal shutdown and diagnostics
    • QFN-32L (9x11x1 mm) package
  • 10.5 to 33 V operating voltage range
  • Green LED (x8) for output on/off status
  • Red LED for process supply power good fault
  • Red LED for overload and overheating
  • Supply reverse polarity protection
  • EMC compliance according to IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino™ UNO R3 connectors
  • CE certified
  • RoHS and China RoHS compliant
  • WEEE compliant

Show More

IMAGE

Image
Image

FEATURED RESOURCES

Schematics BOM Gerber
00 Files selected for download

Technical Documentation

    • Description Version Size Action
      AN4607
      Basics on the thyristor (SCR) structure and its application
      2.0
      317.41 KB
      PDF
      AN4966
      Design guidelines for the shutdown function in the SLLIMM-nano series
      1.0
      1.54 MB
      PDF
      AN4373
      Galvanically-isolated 8 channel high-side driver based on the ISO8200B and ISO8200BQ
      2.0
      2.02 MB
      PDF
      AN4030
      Gate to cathode capacitor, impact on Triac immunity and reliability
      1.0
      223.75 KB
      PDF
      AN4722
      HTS221 digital humidity sensor: hardware guidelines for system integration
      1.0
      844.49 KB
      PDF
      AN4363
      How to select the Triac, ACS, or ACST that fits your application
      2.1
      361.44 KB
      PDF
      AN4608
      How to select the right thyristor (SCR) for your application
      1.0
      895.7 KB
      PDF
      AN4544
      IGBT datasheet tutorial
      1.1
      2.4 MB
      PDF
      AN2648
      Increasing the resolution of analog temperature sensors
      1.4
      161.7 KB
      PDF
      AN441
      Inductive load control with AC switches
      3.2
      712.21 KB
      PDF
      AN4909
      Intelligent power switches for 48 V battery applications
      1.0
      1.07 MB
      PDF
      AN4564
      Is a positive power supply mandatory for my application, or could a negative output work also?
      1.0
      384.04 KB
      PDF
      AN994
      L638xE application guide
      7.1
      560.1 KB
      PDF
      AN1299
      L638xE tricks and tips
      3.0
      718.2 KB
      PDF
      AN4193
      Low duty cycle operation with the SPIRIT1 transceiver
      2.0
      225.38 KB
      PDF
      AN4242
      New generation of 650 V SiC diodes
      2.0
      4.75 MB
      PDF
      AN3168
      Non-insulated SCR / Triac control circuits
      1.2
      315.8 KB
      PDF
      AN4642
      Overview of the BLE Profiles application for X-CUBE-BLE1, expansion for STM32Cube
      3.0
      2.31 MB
      PDF
      AN2703
      Parameter list for SCRs, TRIACs, AC switches, and DIACS
      2.6
      98.99 KB
      PDF
      AN5046
      Printed circuit board assembly recommendations for STMicroelectronics PowerFLAT packages
      4.0
      4.82 MB
      PDF
      AN440
      QII and QIII TRIAC triggering with positive power supply
      3.4
      97.11 KB
      PDF
      AN437
      RC snubber circuit design for TRIACs
      2.6
      587.73 KB
      PDF
      AN533
      SCRs, TRIACs, and AC switches, thermal management precautions for handling and mounting
      3.6
      217.19 KB
      PDF
      AN4840
      SLLIMM™-nano 2nd series small low-loss intelligent molded module
      1.0
      3.63 MB
      PDF
      AN4043
      SLLIMM™-nano small low-loss intelligent molded module
      2.1
      4.83 MB
      PDF
      AN4198
      SPIRIT1: increasing the output power
      1.0
      387.86 KB
      PDF
      AN2684
      STEVAL-IFP006V1: designing with VNI4140K quad high-side smart power solid-state relay ICs
      1.2
      763.53 KB
      PDF
      AN4781
      STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H
      2.0
      3.82 MB
      PDF
      AN4998
      STEVAL-IFP034V1 evaluation board for the IPS161H single high side driver
      2.0
      6.08 MB
      PDF
      AN4923
      STSPIN220: step-mode selection and on-the-fly switching to full-step
      1.0
      404.43 KB
      PDF
      AN4999
      STSPIN32F0 overcurrent protection
      1.1
      741.22 KB
      PDF
      AN439
      Snubberless™ and logic level TRIAC behavior at turn-off
      3.4
      458.5 KB
      PDF
      AN308
      TRIAC analog control circuits for inductive loads
      4.2
      141.89 KB
      PDF
      AN442
      TRIACS AND MICROCONTROLLERS - THE EASY CONNECTION
      2.1
      55.99 KB
      PDF
      AN3169
      Technology performance comparison of Triacs subjected to fast transient voltages
      1.1
      169.53 KB
      PDF
      AN302
      Thyristors and TRIACs: holding current - an important parameter
      3.5
      138.63 KB
      PDF
      AN303
      Thyristors and TRIACs: latching current
      3.4
      164.96 KB
      PDF
      AN4772
      wM-Bus (2013) firmware stack overview
      1.0
      786.08 KB
      PDF
      AN4607

      Basics on the thyristor (SCR) structure and its application

      AN4966

      Design guidelines for the shutdown function in the SLLIMM-nano series

      AN4373

      Galvanically-isolated 8 channel high-side driver based on the ISO8200B and ISO8200BQ

      AN4030

      Gate to cathode capacitor, impact on Triac immunity and reliability

      AN4722

      HTS221 digital humidity sensor: hardware guidelines for system integration

      AN4363

      How to select the Triac, ACS, or ACST that fits your application

      AN4608

      How to select the right thyristor (SCR) for your application

      AN4544

      IGBT datasheet tutorial

      AN2648

      Increasing the resolution of analog temperature sensors

      AN441

      Inductive load control with AC switches

      AN4909

      Intelligent power switches for 48 V battery applications

      AN4564

      Is a positive power supply mandatory for my application, or could a negative output work also?

      AN994

      L638xE application guide

      AN1299

      L638xE tricks and tips

      AN4193

      Low duty cycle operation with the SPIRIT1 transceiver

      AN4242

      New generation of 650 V SiC diodes

      AN3168

      Non-insulated SCR / Triac control circuits

      AN4642

      Overview of the BLE Profiles application for X-CUBE-BLE1, expansion for STM32Cube

      AN2703

      Parameter list for SCRs, TRIACs, AC switches, and DIACS

      AN5046

      Printed circuit board assembly recommendations for STMicroelectronics PowerFLAT packages

      AN440

      QII and QIII TRIAC triggering with positive power supply

      AN437

      RC snubber circuit design for TRIACs

      AN533

      SCRs, TRIACs, and AC switches, thermal management precautions for handling and mounting

      AN4840

      SLLIMM™-nano 2nd series small low-loss intelligent molded module

      AN4043

      SLLIMM™-nano small low-loss intelligent molded module

      AN4198

      SPIRIT1: increasing the output power

      AN2684

      STEVAL-IFP006V1: designing with VNI4140K quad high-side smart power solid-state relay ICs

      AN4781

      STEVAL-IFP028V1 evaluation board for single high-side driver IPS160H

      AN4998

      STEVAL-IFP034V1 evaluation board for the IPS161H single high side driver

      AN4923

      STSPIN220: step-mode selection and on-the-fly switching to full-step

      AN4999

      STSPIN32F0 overcurrent protection

      AN439

      Snubberless™ and logic level TRIAC behavior at turn-off

      AN308

      TRIAC analog control circuits for inductive loads

      AN442

      TRIACS AND MICROCONTROLLERS - THE EASY CONNECTION

      AN3169

      Technology performance comparison of Triacs subjected to fast transient voltages

      AN302

      Thyristors and TRIACs: holding current - an important parameter

      AN303

      Thyristors and TRIACs: latching current

      AN4772

      wM-Bus (2013) firmware stack overview

    • Description Version Size Action
      TN1219
      HTS221 digital humidity sensor: reference design implementation
      2.0
      367.08 KB
      PDF
      TN1218
      Interpreting humidity and temperature readings in the HTS221 digital humidity sensor
      4.0
      3.67 MB
      PDF
      TN1221
      Mounting instruction for SLLIMM™ -nano 2nd series (N2DIP-26L)
      1.0
      542.38 KB
      PDF
      TN1037
      SLLIMM™-nano mounting instructions and heatsink
      3.0
      1.21 MB
      PDF
      TN1198
      Surface mount guidelines for MEMS sensors in HLGA packages
      1.0
      128.17 KB
      PDF
      TN1219

      HTS221 digital humidity sensor: reference design implementation

      TN1218

      Interpreting humidity and temperature readings in the HTS221 digital humidity sensor

      TN1221

      Mounting instruction for SLLIMM™ -nano 2nd series (N2DIP-26L)

      TN1037

      SLLIMM™-nano mounting instructions and heatsink

      TN1198

      Surface mount guidelines for MEMS sensors in HLGA packages

    • Description Version Size Action
      UM1483
      Low power motor control board STEVAL-IHM036V1 featuring SLLIMM™ STGIPN3H60 and MCU STM32F100C6T6B
      1.1
      591.59 KB
      PDF
      UM2325
      ST PowerStudio dynamic electrothermal simulation software for power devices
      2.0
      2.93 MB
      PDF
      UM1483

      Low power motor control board STEVAL-IHM036V1 featuring SLLIMM™ STGIPN3H60 and MCU STM32F100C6T6B

      UM2325

      ST PowerStudio dynamic electrothermal simulation software for power devices

    • Description Version Size Action
      PM0237
      BlueNRG, BlueNRG-MS stacks programming guidelines
      7.0
      1.78 MB
      PDF
      PM0257
      BlueNRG-1, BlueNRG-2 BLE stack v2.x programming guidelines
      4.0
      1.06 MB
      PDF
      PM0237

      BlueNRG, BlueNRG-MS stacks programming guidelines

      PM0257

      BlueNRG-1, BlueNRG-2 BLE stack v2.x programming guidelines

Presentations & Training Material

    • Description Version Size Action
      An introduction to electric motors 1.0
      2.23 MB
      PDF
      X-NUCLEO-IDB05A1 Quick start guide 1.6
      1.42 MB
      PDF

      An introduction to electric motors

      X-NUCLEO-IDB05A1 Quick start guide

Publications and Collaterals

    • Description Version Size Action
      1200V SiC diodes, 2 to 40 A in surface-mount and through-hole packages 1.0
      748.77 KB
      PDF
      800-1050V MDmesh™ K5 ST’s first super-junction VHV MOSFET Series 1.0
      516.44 KB
      PDF
      BlueNRG-1 Ultra-low-power Bluetooth® Low Energy System-on-Chip 1
      714.73 KB
      PDF
      BlueNRG-2 The IoT Ready Bluetooth® low energy System-on-Chip 4.0
      403.31 KB
      PDF
      DC-DC converters
      557.92 KB
      PDF
      Field-Effect Rectifier Diodes Advantageously replace Schottky (60V and 100V) 1.0
      1.29 MB
      PDF
      IPS160H/IPS161H - Ready for tomorrow’s factory automation 08.2017
      341.83 KB
      PDF
      ISO8200BQ - Leading innovation for industrial automation 08.2017
      363.54 KB
      PDF
      Industrial-grade SiC diodes - 650V and low VF - to boost the performance of power converters 2.0
      958.23 KB
      PDF
      L6984, L6986 Energy saving synchronous DC-DC converters for industrial
      1.24 MB
      PDF
      S2-LP:Ultra-low-power, high-performance, sub-1GHz RF transceiver 4.0
      1.47 MB
      PDF
      SOD123Flat power Schottky diodes for improved cost and space-savings 1.0
      2.03 MB
      PDF
      SOD128Flat power Schottky diodes for improved cost and space-savings 1.0
      2.18 MB
      PDF
      ST Diodes Finder : the new app for Android and iOS 2.0
      1.46 MB
      PDF
      ST Thyristor Finder: SCRs and Triacs on Android and iOS 1.0
      854.07 KB
      PDF
      STSPIN motor drivers - The best things come in small packages 02.2018
      952.6 KB
      PDF

      1200V SiC diodes, 2 to 40 A in surface-mount and through-hole packages

      800-1050V MDmesh™ K5 ST’s first super-junction VHV MOSFET Series

      BlueNRG-1 Ultra-low-power Bluetooth® Low Energy System-on-Chip

      BlueNRG-2 The IoT Ready Bluetooth® low energy System-on-Chip

      DC-DC converters

      Field-Effect Rectifier Diodes Advantageously replace Schottky (60V and 100V)

      IPS160H/IPS161H - Ready for tomorrow’s factory automation

      ISO8200BQ - Leading innovation for industrial automation

      Industrial-grade SiC diodes - 650V and low VF - to boost the performance of power converters

      L6984, L6986 Energy saving synchronous DC-DC converters for industrial

      S2-LP:Ultra-low-power, high-performance, sub-1GHz RF transceiver

      SOD123Flat power Schottky diodes for improved cost and space-savings

      SOD128Flat power Schottky diodes for improved cost and space-savings

      ST Diodes Finder : the new app for Android and iOS

      ST Thyristor Finder: SCRs and Triacs on Android and iOS

      STSPIN motor drivers - The best things come in small packages

    • Description Version Size Action
      Linear and Switching Voltage Regulators Selection Guide 3.0
      370.88 KB
      PDF
      STSPIN motor drivers 11.2017
      1.6 MB
      PDF
      Thyristors, Triacs, AC switches and A.S.D™ selection guide 2.0
      1.51 MB
      PDF
      X-NUCLEO expansion boards motor control - Selection guide 1.2
      263.59 KB
      PDF

      Linear and Switching Voltage Regulators Selection Guide

      STSPIN motor drivers

      Thyristors, Triacs, AC switches and A.S.D™ selection guide

      X-NUCLEO expansion boards motor control - Selection guide

    • Description Version Size Action
      Intelligent power switches (IPS) 04.2018
      4.21 MB
      PDF
      Motor Control Reference Guide 15.10
      2.61 MB
      PDF
      Products and solutions for Smart industry 3.0
      2.99 MB
      PDF

      Intelligent power switches (IPS)

      Motor Control Reference Guide

      Products and solutions for Smart industry

    • Description Version Size Action
      STSPIN Motor Control: Design Considerations for Brushless Direct Current Motor Control 1.0
      5.54 MB
      PDF

      STSPIN Motor Control: Design Considerations for Brushless Direct Current Motor Control

Embedded Software

    • Part Number

      Bluetooth Low Energy software expansion for STM32Cube

      Low voltage brush DC motor driver software expansion for STM32Cube

      Low voltage three-phase brushless DC motor driver software expansion for STM32Cube

      Low voltage stepper motor driver software expansion for STM32Cube

      Sub-1 GHz RF communication software expansion for STM32Cube

    • Part Number

      Standard C platform-independent drivers for MEMS motion and environmental sensors

    • Part Number

      STSW-BNRG-S2LP evaluation software package based on BlueNRG-1 and S2-LP

      BlueNRG current consumption estimation tool

eDesignSuite

Converter

Input

V This option is required. And must be less than or equal to Volt. Max [V]
V This option is required. And must be greater than or equal to Volt. Min [V]

Output Power

V This option is required and must be a number.
A This option is required and must be a number.

Diodes and Rectifiers

Part number Description
STPSC12065 650 V power Schottky silicon carbide diode
STPSC20065 650 V power Schottky silicon carbide diode
STPSC20H12 1200 V, 20 A High surge Silicon Carbide Power Schottky Diode
Part number
650 V power Schottky silicon carbide diode
650 V power Schottky silicon carbide diode
1200 V, 20 A High surge Silicon Carbide Power Schottky Diode

EMI Filtering and Signal Conditioning

Part number Description
BALF-NRG-02D3 50Ω / conjugate match balun to BlueNRG transceiver, with integrated harmonic filter
BALF-SPI-01D3 50Ω nominal input / conjugate match balun to SPIRIT1, with integrated harmonic filter
Part number
50Ω / conjugate match balun to BlueNRG transceiver, with integrated harmonic filter
50Ω nominal input / conjugate match balun to SPIRIT1, with integrated harmonic filter

Interfaces and Transceivers

Part number Description
STKNX Miniature KNX transceiver with voltage regulators
Part number
Miniature KNX transceiver with voltage regulators

MEMS and Sensors

Part number Description
HTS221 Capacitive digital sensor for relative humidity and temperature
STLM20 Analog temperature sensor, ultra-low current 2.4 V, high precision
STTS751 2.25 V low-voltage local digital temperature sensor
Part number
Capacitive digital sensor for relative humidity and temperature
Analog temperature sensor, ultra-low current 2.4 V, high precision
2.25 V low-voltage local digital temperature sensor

Motor Drivers

Part number Description
STSPIN220 Low voltage stepper motor driver
STSPIN233 Low voltage three phase and three sense motor driver
STSPIN250 Low voltage brush DC motor driver
Part number
Low voltage stepper motor driver
Low voltage three phase and three sense motor driver
Low voltage brush DC motor driver

Power Management

Part number Description
IPS160H Single high-side switch for safety integrity level (SIL2 and SIL3) compliant systems
IPS161H Single high-side switch for safety integrity level (SIL2 and SIL3) compliant systems
ISO8200B Galvanic isolated octal high side smart power solid state relay
ISO8200BQ Galvanic isolated octal high-side smart power solid state-relay
L6370Q 2.5 A single high-side smart power switch
L6491 High voltage high and low-side 4 A gate driver
L6985F 38 V 500 mA synchronous step-down switching regulator with 30 uA quiescent current
L6986 38 V 2 A synchronous step-down switching regulator with 30 uA quiescent current
L6986F 38 V 1.5 A synchronous step-down switching regulator with 30 uA quiescent current
L7985 2A step-down switching regulator
L7986 3A step-down switching regulator
L7987 61 V 3 A asynchronous step-down switching regulator with adjustable current limitation
L7987L 61 V 2 A asynchronous step-down switching regulator with adjustable current limitation
LD39130S 300 mA very low quiescent current Linear regulator IC with automatic Green mode
LDF 1A Very low drop voltage regulator IC
LDFM 500 mA very low drop voltage regulator
LDK120 200 mA low quiescent current very low noise LDO
LDK130 300 mA low quiescent current very low noise LDO
LDK220 200 mA low quiescent current and low noise LDO
LDK320 200 mA low quiescent current and high PSRR voltage regulator
LDL212 1.2A Low Drop Linear Regulator IC
ST1S12XX Synchronous rectification with inhibit, 0.7 A, 1.7 MHz adjustable, step-down switching regulator
ST1S14 Up to 3 A step down switching regulator
VN751PT High side driver
VNI2140J Dual high side smart power solid state relay
VNI4140K Quad high-side smart power solid-state relay
VNI8200XP Octal high side smart power solid state relay with serial/parallel selectable interface on chip
Part number
Single high-side switch for safety integrity level (SIL2 and SIL3) compliant systems
Single high-side switch for safety integrity level (SIL2 and SIL3) compliant systems
Galvanic isolated octal high side smart power solid state relay
Galvanic isolated octal high-side smart power solid state-relay
2.5 A single high-side smart power switch
High voltage high and low-side 4 A gate driver
38 V 500 mA synchronous step-down switching regulator with 30 uA quiescent current
38 V 2 A synchronous step-down switching regulator with 30 uA quiescent current
38 V 1.5 A synchronous step-down switching regulator with 30 uA quiescent current
2A step-down switching regulator
3A step-down switching regulator
61 V 3 A asynchronous step-down switching regulator with adjustable current limitation
61 V 2 A asynchronous step-down switching regulator with adjustable current limitation
300 mA very low quiescent current Linear regulator IC with automatic Green mode
1A Very low drop voltage regulator IC
500 mA very low drop voltage regulator
200 mA low quiescent current very low noise LDO
300 mA low quiescent current very low noise LDO
200 mA low quiescent current and low noise LDO
200 mA low quiescent current and high PSRR voltage regulator
1.2A Low Drop Linear Regulator IC
Synchronous rectification with inhibit, 0.7 A, 1.7 MHz adjustable, step-down switching regulator
Up to 3 A step down switching regulator
High side driver
Dual high side smart power solid state relay
Quad high-side smart power solid-state relay
Octal high side smart power solid state relay with serial/parallel selectable interface on chip

Power Transistors

Part number Description
STF18N65M5 N-channel 650 V, 0.198 Ohm typ., 15 A MDmesh M5 Power MOSFET in TO-220FP package
STF24N60M2 N-channel 600 V, 0.168 Ohm typ., 18 A MDmesh M2 Power MOSFET in TO-220FP package
STF33N60M2 N-channel 600 V, 0.108 Ohm typ., 26 A MDmesh M2 Power MOSFETs in TO-220FP package
STF34N65M5 N-channel 650 V, 0.09 Ohm typ., 28 A MDmesh M5 Power MOSFET in TO-220FP package
STF7N105K5 N-channel 1050 V, 1.4 Ohm typ., 4 A MDmesh K5 Power MOSFETs in TO-220FP package
STF7N90K5 N-channel 900 V, 0.72 Ohm typ., 7 A MDmesh K5 Power MOSFET in a TO-220FP package
STF8N90K5 N-channel 900 V, 0.60 Ohm typ., 8 A MDmesh K5 Power MOSFET in a TO-220FP package
STL150N3LLH6 N-channel 30 V, 0.0016 Ohm typ., 33 A STripFET(TM) VI DeepGATE(TM) Power MOSFET in PowerFLAT(TM) 5x6 package
STL19N60M2 N-channel 600 V, 0.278 Ohm typ., 11 A MDmesh M2 Power MOSFET in a PowerFLAT 8x8 HV package
STL20N6F7 N-channel 60 V, 0.0046 Ohm typ., 20 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package
STL50N6F7 N-channel 60 V, 9 mOhm typ., 60 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
STW12N150K5 N-channel 1500 V, 1.6 Ohm typ., 7 A MDmesh K5 Power MOSFET in a TO-247 package
STW69N65M5 N-channel 650 V, 0.037 Ohm typ., 58 A MDmesh M5 Power MOSFET in TO-247 package
Part number
N-channel 650 V, 0.198 Ohm typ., 15 A MDmesh M5 Power MOSFET in TO-220FP package
N-channel 600 V, 0.168 Ohm typ., 18 A MDmesh M2 Power MOSFET in TO-220FP package
N-channel 600 V, 0.108 Ohm typ., 26 A MDmesh M2 Power MOSFETs in TO-220FP package
N-channel 650 V, 0.09 Ohm typ., 28 A MDmesh M5 Power MOSFET in TO-220FP package
N-channel 1050 V, 1.4 Ohm typ., 4 A MDmesh K5 Power MOSFETs in TO-220FP package
N-channel 900 V, 0.72 Ohm typ., 7 A MDmesh K5 Power MOSFET in a TO-220FP package
N-channel 900 V, 0.60 Ohm typ., 8 A MDmesh K5 Power MOSFET in a TO-220FP package
N-channel 30 V, 0.0016 Ohm typ., 33 A STripFET(TM) VI DeepGATE(TM) Power MOSFET in PowerFLAT(TM) 5x6 package
N-channel 600 V, 0.278 Ohm typ., 11 A MDmesh M2 Power MOSFET in a PowerFLAT 8x8 HV package
N-channel 60 V, 0.0046 Ohm typ., 20 A STripFET F7 Power MOSFET in a PowerFLAT 3.3x3.3 package
N-channel 60 V, 9 mOhm typ., 60 A STripFET F7 Power MOSFET in a PowerFLAT 5x6 package
N-channel 1500 V, 1.6 Ohm typ., 7 A MDmesh K5 Power MOSFET in a TO-247 package
N-channel 650 V, 0.037 Ohm typ., 58 A MDmesh M5 Power MOSFET in TO-247 package

Wireless Transceivers, MCUs and Modules

Part number Description
BlueNRG-2 Bluetooth® low energy wireless system-on-chip
BlueNRG-MS Bluetooth Low Energy Network Processor supporting Bluetooth 4.2 core specification
S2-LP Ultra-low power, high performance, sub-1GHz transceiver
SPBTLE-1S Very low power application module for Bluetooth® Smart v4.2
SPBTLE-RF Very low power module for Bluetooth Smart v4.1
SPIRIT1 Low data rate, low power Sub 1GHz transceiver
SPSGRF Sub-GHz (868 or 915 MHz) low power programmable RF transceiver modules
STS1TX Low data rate, low power sub-1GHz transmitter
Part number
Bluetooth® low energy wireless system-on-chip
Bluetooth Low Energy Network Processor supporting Bluetooth 4.2 core specification
Ultra-low power, high performance, sub-1GHz transceiver
Very low power application module for Bluetooth® Smart v4.2
Very low power module for Bluetooth Smart v4.1
Low data rate, low power Sub 1GHz transceiver
Sub-GHz (868 or 915 MHz) low power programmable RF transceiver modules
Low data rate, low power sub-1GHz transmitter